| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Fri, 13 Oct 2006 13:26:03 +0400
From: Andrey Panin <pazke@...pac.ru>
To: Burman Yan <yan_952@...mail.com>
Cc: linux-kernel@...r.kernel.org
Subject: Re: [PATCH] HP mobile data protection system driver
On 286, 10 13, 2006 at 10:47:15 +0200, Burman Yan wrote:
> Hi, all.
>
> I'm new to the list so forgive me in advance for any netiquette mistakes I
> make.
>
> I wrote a driver for the accelerometer chip on HP nc6400 laptop (I think
> the same chip is present on
> other NCxxxx models). This driver uses ACPI interface present in the bios
> and behaves pretty much like
> hdaps. This is a fully functional version - tested on 2.6.17 and 2.6.18
> (not 2.6.19-rc1 since I have a
> problem with that kernel on my laptop). It applies on 2.6.19-rc1 as well
> though. I would like your
> remarks and suggestions on this. Also, should I mail this patch to a kernel
> maintainer? I could not find a maintainer that looks like the address for
> this patch. The closest one is the lm_sensors maintainer, but
> that's probably wrong.
Some comments:
1. Use hard tabs instead of 8 spaces;
2. C++ comments are tolerated, but not welcomed;
3. You missed Signed-off-by: line.
diff -Nrubp linux-2.6.18.orig/drivers/hwmon/Kconfig linux-2.6.18.mdps/drivers/hwmon/Kconfig
--- linux-2.6.18.orig/drivers/hwmon/Kconfig 2006-10-11 14:20:08.000000000 +0200
+++ linux-2.6.18.mdps/drivers/hwmon/Kconfig 2006-10-13 08:52:42.000000000 +0200
@@ -507,6 +507,22 @@ config SENSORS_HDAPS
Say Y here if you have an applicable laptop and want to experience
the awesome power of hdaps.
+config SENSORS_MDPS
+ tristate "HP Mobile Data Protection System 3D (mdps)"
+ depends on ACPI && HWMON && INPUT && X86
+ default n
+ help
+ This driver provides support for the HP Mobile Data Protection
+ System 3D (mdps), which is an accelerometer. Only HP nc6400 is supported
+ right now, but it may work on other models as well. The
+ accelerometer data is readable via /proc/drivers/mdps.
+
+ This driver also provides an absolute input class device, allowing
+ the laptop to act as a pinball machine-esque joystick.
+
+ This driver can also be built as a module. If so, the module
+ will be called mdps.
+
config HWMON_DEBUG_CHIP
bool "Hardware Monitoring Chip debugging messages"
depends on HWMON
diff -Nrubp linux-2.6.18.orig/drivers/hwmon/Makefile linux-2.6.18.mdps/drivers/hwmon/Makefile
--- linux-2.6.18.orig/drivers/hwmon/Makefile 2006-10-11 14:20:08.000000000 +0200
+++ linux-2.6.18.mdps/drivers/hwmon/Makefile 2006-10-13 10:14:10.000000000 +0200
@@ -26,6 +26,7 @@ obj-$(CONFIG_SENSORS_FSCPOS) += fscpos.o
obj-$(CONFIG_SENSORS_GL518SM) += gl518sm.o
obj-$(CONFIG_SENSORS_GL520SM) += gl520sm.o
obj-$(CONFIG_SENSORS_HDAPS) += hdaps.o
+obj-$(CONFIG_SENSORS_MDPS) += mdps.o
obj-$(CONFIG_SENSORS_IT87) += it87.o
obj-$(CONFIG_SENSORS_LM63) += lm63.o
obj-$(CONFIG_SENSORS_LM70) += lm70.o
diff -Nrubp linux-2.6.18.orig/drivers/hwmon/mdps.c linux-2.6.18.mdps/drivers/hwmon/mdps.c
--- linux-2.6.18.orig/drivers/hwmon/mdps.c 1970-01-01 02:00:00.000000000 +0200
+++ linux-2.6.18.mdps/drivers/hwmon/mdps.c 2006-10-13 10:13:49.000000000 +0200
@@ -0,0 +1,700 @@
+/*
+ * mdps.c - HP Mobile Data Protection System 3D ACPI driver
+ *
+ * Copyright (C) 2006 Yan Burman
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
+#include <linux/input.h>
+#include <linux/kthread.h>
+#include <linux/delay.h>
+
+#include <acpi/acpi_drivers.h>
+#include <acpi/acnamesp.h>
+
+#include <asm/uaccess.h>
+
+#define VERSION "0.1"
+
+MODULE_DESCRIPTION("HP three-axis digital accelerometer ACPI driver");
+MODULE_AUTHOR("Yan Burman (yan_952@...mail.com)");
+MODULE_VERSION(VERSION);
+MODULE_LICENSE("GPL");
+
+#define DRIVER_NAME "mdps"
+#define ACPI_MDPS_CLASS "accelerometer"
+#define ACPI_MDPS_ID "HPQ0004"
+
+#define MDPS_PROC_ROOT "driver/mdps"
+
+// The actual chip is STMicroelectronics LIS3LV02DL or LIS3LV02DQ
+
+#define MDPS_WHO_AM_I 0x0F //r 00111010
+#define MDPS_OFFSET_X 0x16 //rw
+#define MDPS_OFFSET_Y 0x17 //rw
+#define MDPS_OFFSET_Z 0x18 //rw
+#define MDPS_GAIN_X 0x19 //rw
+#define MDPS_GAIN_Y 0x1A //rw
+#define MDPS_GAIN_Z 0x1B //rw
+#define MDPS_CTRL_REG1 0x20 //rw 00000111
+#define MDPS_CTRL_REG2 0x21 //rw 00000000
+#define MDPS_CTRL_REG3 0x22 //rw 00001000
+#define MDPS_HP_FILTER RESET 0x23 //r
+#define MDPS_STATUS_REG 0x27 //rw 00000000
+#define MDPS_OUTX_L 0x28 //r
+#define MDPS_OUTX_H 0x29 //r
+#define MDPS_OUTY_L 0x2A //r
+#define MDPS_OUTY_H 0x2B //r
+#define MDPS_OUTZ_L 0x2C //r
+#define MDPS_OUTZ_H 0x2D //r
+#define MDPS_FF_WU_CFG 0x30 //rw 00000000
+#define MDPS_FF_WU_SRC 0x31 //rw 00000000
+#define MDPS_FF_WU_ACK 0x32 //r
+#define MDPS_FF_WU_THS_L 0x34 //rw 00000000
+#define MDPS_FF_WU_THS_H 0x35 //rw 00000000
+#define MDPS_FF_WU_DURATION 0x36 //rw 00000000
+#define MDPS_DD_CFG 0x38 //rw 00000000
+#define MDPS_DD_SRC 0x39 //rw 00000000
+#define MDPS_DD_ACK 0x3A //r
+#define MDPS_DD_THSI_L 0x3C //rw 00000000
+#define MDPS_DD_THSI_H 0x3D //rw 00000000
+#define MDPS_DD_THSE_L 0x3E //rw 00000000
+#define MDPS_DD_THSE_H 0x3F //rw 00000000
+
+#define MDPS_ID 0x3A
+
+// mouse device poll interval in milliseconds
+#define MDPS_POLL_INTERVAL 30
+
+static unsigned int mouse;
+module_param(mouse, bool, 0);
+MODULE_PARM_DESC(mouse, "Enable the input class device on module load");
+
+#ifdef CONFIG_PROC_FS
+static unsigned int power_off;
+module_param(power_off, bool, 0);
+MODULE_PARM_DESC(power_off, "Turn off device on module load");
+#endif
+
+struct acpi_mdps
+{
+ struct acpi_device* device; /* The ACPI device */
+ u32 irq; /* IRQ number */
+ struct input_dev* idev; /* input device */
+ struct task_struct* kthread; /* kthread for input */
+ int xcalib; /* calibrated null value for x */
+ int ycalib; /* calibrated null value for y */
+ int is_on; /* whether the device is on or off */
+#ifdef CONFIG_PROC_FS
+ struct proc_dir_entry *dir;
+#endif
+};
+
+static struct acpi_mdps mdps;
+
+static int mdps_add(struct acpi_device *device);
+static int mdps_remove(struct acpi_device *device, int type);
+static int mdps_suspend(struct acpi_device * device, int state);
+static int mdps_resume(struct acpi_device * device, int state);
+static int mdps_remove_fs(void);
+static int mdps_add_fs(struct acpi_device *device);
+static void mdps_mouse_enable(void);
+static void mdps_mouse_disable(void);
+
+static struct acpi_driver mdps_driver =
+{
+ .name = DRIVER_NAME,
+ .class = ACPI_MDPS_CLASS,
+ .ids = ACPI_MDPS_ID,
+ .ops = {
+ .add = mdps_add,
+ .remove = mdps_remove,
+ .suspend = mdps_suspend,
+ .resume = mdps_resume
+ }
Strange indentation.
+};
+
+/** Create a single value from 2 bytes received from the accelerometer
+ * @param hi the high byte
+ * @param lo the low byte
+ * @return the resulting value
+ */
Hmm, kernel doesn't use doxygen...
+static inline s16 mdps_glue_bytes(unsigned long hi, unsigned long lo)
+{
+ // In "12 bit right justified" mode, bit 6, bit 7, bit 8 = bit 5
+ if (hi & 0x10)
+ hi |= 0xE0;
+ return (s16)(lo | ((hi << 8)));
+}
+
+static acpi_status read_acpi_int_param(acpi_handle handle, acpi_string method,
+ int val, unsigned long* ret)
+{
+ union acpi_object arg0 = { ACPI_TYPE_INTEGER };
+ struct acpi_object_list args = { 1, &arg0 };
+
+ arg0.integer.value = val;
+
+ return acpi_evaluate_integer(handle, method, &args, ret);
+}
+
+/** ACPI _STA method: get device status
+ * @param handle the handle of the device
+ * @param[out] ret result of the operation
+ * @return AE_OK on success
+ */
+static inline acpi_status mdps__STA(acpi_handle handle, unsigned long* ret)
+{
+ return acpi_evaluate_integer(handle, METHOD_NAME__STA, NULL, ret);
+}
+
+/** ACPI ALRD method: read a register
+ * @param handle the handle of the device
+ * @param reg the register to read
+ * @param[out] ret result of the operation
+ * @return AE_OK on success
+ */
+static inline acpi_status mdps_ALRD(acpi_handle handle, int reg,
+ unsigned long* ret)
+{
+ return read_acpi_int_param(handle, "ALRD", reg, ret);
+}
+
+/** ACPI _INI method: initialize the device.
+ * @param handle the handle of the device
+ * @return 0 on success
+ */
+static inline acpi_status mdps__INI(acpi_handle handle)
+{
+ return acpi_evaluate_object(handle, METHOD_NAME__INI, NULL, NULL);
+}
+
+/** ACPI ALWR method: write to a register
+ * @param handle the handle of the device
+ * @param reg the register to write to
+ * @param val the value to write
+ * @param[out] ret result of the operation
+ * @return AE_OK on success
+ */
+static acpi_status mdps_ALWR(acpi_handle handle, int reg, int val,
+ unsigned long* ret)
+{
+ union acpi_object in_obj[2];
+ struct acpi_object_list args;
+
+ args.count = 2;
+ args.pointer = in_obj;
+ in_obj[0].type = ACPI_TYPE_INTEGER;
+ in_obj[0].integer.value = reg;
+ in_obj[1].type = ACPI_TYPE_INTEGER;
+ in_obj[1].integer.value = val;
+
+ return acpi_evaluate_integer(handle, "ALWR", &args, ret);
+}
+
+static int mdps_get_xy(acpi_handle handle, int* x, int* y)
+{
+ unsigned long x_lo, x_hi, y_lo, y_hi;
+
+ mdps_ALRD(mdps.device->handle, MDPS_OUTX_L, &x_lo);
+ mdps_ALRD(mdps.device->handle, MDPS_OUTX_H, &x_hi);
+ mdps_ALRD(mdps.device->handle, MDPS_OUTY_L, &y_lo);
+ mdps_ALRD(mdps.device->handle, MDPS_OUTY_H, &y_hi);
+
+ *x = mdps_glue_bytes(x_hi, x_lo);
+ *y = mdps_glue_bytes(y_hi, y_lo);
+
+ return 0;
+}
+
+static int mdps_mouse_kthread(void *data)
+{
+ int x, y;
+
+ while (!kthread_should_stop()) {
+ mdps_get_xy(mdps.device->handle, &x, &y);
+
+ // need to invert the X axis for this to look natural
+ input_report_abs(mdps.idev, ABS_X, -(x - mdps.xcalib));
+ input_report_abs(mdps.idev, ABS_Y, y - mdps.ycalib);
+
+ input_sync(mdps.idev);
+
+ msleep_interruptible(MDPS_POLL_INTERVAL);
+ }
+
+ return 0;
+}
+
+static inline int mdps_poweroff(acpi_handle handle)
+{
+ unsigned long ret;
+ mdps.is_on = 0;
+ return (mdps_ALWR(handle, MDPS_CTRL_REG1, 0x00, &ret) == AE_OK);
+}
+
+static inline int mdps_poweron(acpi_handle handle)
+{
+ mdps.is_on = 1;
+ return (mdps__INI(handle) == AE_OK);
+}
+
+int mdps_suspend(struct acpi_device * device, int state)
This function was declared static earlier.
+{
+ mdps_poweroff(mdps.device->handle);
+
+ mdps_mouse_disable();
+
+ return 0;
+}
+
+int mdps_resume(struct acpi_device * device, int state)
Missing static again.
+{
+ mdps_poweron(mdps.device->handle);
+
+ if (mouse)
+ mdps_mouse_enable();
+
+ return 0;
+}
+
+static acpi_status
+mdps_get_resource(struct acpi_resource *resource, void *context)
+{
+ if (resource->type == ACPI_RESOURCE_TYPE_EXTENDED_IRQ) {
+ struct acpi_resource_extended_irq* irq;
+ u32* device_irq = context;
+
+ irq = &resource->data.extended_irq;
+ *device_irq = irq->interrupts[0];
+ }
+
+ return AE_OK;
+}
+
+static void mdps_enum_resources(struct acpi_device * device)
+{
+ acpi_status status;
+
+ status = acpi_walk_resources(device->handle, METHOD_NAME__CRS,
+ mdps_get_resource, &mdps.irq);
+ if (ACPI_FAILURE(status))
+ printk(KERN_DEBUG "mdps: Error getting resources\n");
+}
+
+int mdps_add(struct acpi_device *device)
And again. And some more below, please check.
+{
+ unsigned long val;
+
+ if (!device)
+ return -EINVAL;
+
+ mdps.device = device;
+ strcpy(acpi_device_name(device), "mdps");
+ strcpy(acpi_device_class(device), ACPI_MDPS_CLASS);
+ acpi_driver_data(device) = &mdps;
+
+ mdps_ALRD(device->handle, MDPS_WHO_AM_I, &val);
+ if (val != MDPS_ID) {
+ printk(KERN_INFO "mdps: Accelerometer chip not LIS3LV02D{L,Q}\n");
+ return -ENODEV;
+ }
+
+ mdps_enum_resources(device);
+ mdps_add_fs(device);
+ mdps_resume(device, 3);
+
+#ifdef CONFIG_PROC_FS
+ if (power_off)
+ mdps_poweroff(mdps.device->handle);
+#endif
+
+ return 0;
+}
+
+int mdps_remove(struct acpi_device *device, int type)
+{
+ if (!device)
+ return -EINVAL;
+
+ if (mouse)
+ mdps_mouse_disable();
+
+ return mdps_remove_fs();
+}
+
+static inline void mdps_calibrate_mouse(void)
+{
+ int x, y;
+ mdps_get_xy(mdps.device->handle, &x, &y);
+
+ mdps.xcalib = x;
+ mdps.ycalib = y;
+}
+
+#ifdef CONFIG_PROC_FS
+static int mdps_proc_position_show(struct seq_file *seq, void *v)
+{
+ unsigned long z_lo, z_hi;
+ int x, y, z;
+
+ mdps_get_xy(mdps.device->handle, &x, &y);
+
+ mdps_ALRD(mdps.device->handle, MDPS_OUTZ_L, &z_lo);
+ mdps_ALRD(mdps.device->handle, MDPS_OUTZ_H, &z_hi);
+
+ z = mdps_glue_bytes(z_hi, z_lo);
+
+ seq_printf(seq, "(%d, %d, %d)\n", x, y, z);
+
+ return 0;
+}
+
+static int mdps_proc_state_show(struct seq_file *seq, void *v)
+{
+ seq_puts(seq, (mdps.is_on ? "on\n" : "off\n"));
+
+ return 0;
+}
+
+static int mdps_proc_calibrate_mouse_show(struct seq_file *seq, void *v)
+{
+ return 0;
+}
+
+static int mdps_proc_mouse_show(struct seq_file *seq, void *v)
+{
+ seq_puts(seq, (mouse ? "enabled\n" : "disabled\n"));
+
+ return 0;
+}
+
+static ssize_t
+mdps_write_calibrate_mouse(struct file *file, const char __user * buffer,
+ size_t count, loff_t * ppos)
+{
+ mdps_calibrate_mouse();
+
+ return count;
+}
+
+static int mdps_proc_rate_show(struct seq_file *seq, void *v)
+{
+ unsigned long ctrl;
+ int rate = 0;
+
+ mdps_ALRD(mdps.device->handle, MDPS_CTRL_REG1, &ctrl);
+
+ switch (ctrl & 0x30)
+ {
+ case 0x00:
+ rate = 40;
+ break;
+
+ case 0x10:
+ rate = 160;
+ break;
+
+ case 0x20:
+ rate = 640;
+ break;
+
+ case 0x30:
+ rate = 2560;
+ break;
+ }
+
+ seq_printf(seq, "sampling rate:\t%dHz\n", rate);
+
+ return 0;
+}
+
+static ssize_t
+mdps_write_state(struct file *file, const char __user * buffer,
+ size_t count, loff_t * ppos)
+{
+ char state_string[12] = { '\0' };
+
+ if ((count > sizeof(state_string) - 1))
+ return -EINVAL;
+
+ if (copy_from_user(state_string, buffer, count))
+ return -EFAULT;
+
+ state_string[count] = '\0';
+
+ mdps.is_on = simple_strtoul(state_string, NULL, 0);
+
+ if (mdps.is_on)
+ mdps_poweron(mdps.device->handle);
+ else
+ mdps_poweroff(mdps.device->handle);
+
+ return count;
+}
+
+static ssize_t mdps_write_mouse(struct file *file, const char __user * buffer,
+ size_t count, loff_t * ppos)
+{
+ char state_string[12] = { '\0' };
+
+ if ((count > sizeof(state_string) - 1))
+ return -EINVAL;
+
+ if (copy_from_user(state_string, buffer, count))
+ return -EFAULT;
+
+ state_string[count] = '\0';
+
+ mouse = simple_strtoul(state_string, NULL, 0);
+
+ if (mouse)
+ mdps_mouse_enable();
+ else
+ mdps_mouse_disable();
+
+ return count;
+}
+
+static int mdps_proc_position_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, mdps_proc_position_show, NULL);
+}
+
+static int mdps_proc_state_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, mdps_proc_state_show, NULL);
+}
+
+static int mdps_proc_rate_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, mdps_proc_rate_show, NULL);
+}
+
+static int mdps_proc_mouse_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, mdps_proc_mouse_show, NULL);
+}
+
+static int mdps_proc_calibrate_mouse_open(struct inode *inode,
+ struct file *file)
+{
+ return single_open(file, mdps_proc_calibrate_mouse_show, NULL);
+}
+
+static const struct file_operations mdps_proc_position_fops =
+{
+ .owner = THIS_MODULE,
+ .open = mdps_proc_position_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static const struct file_operations mdps_proc_state_fops =
+{
+ .owner = THIS_MODULE,
+ .open = mdps_proc_state_open,
+ .read = seq_read,
+ .write = mdps_write_state,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static const struct file_operations mdps_proc_mouse_fops =
+{
+ .owner = THIS_MODULE,
+ .open = mdps_proc_mouse_open,
+ .read = seq_read,
+ .write = mdps_write_mouse,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static const struct file_operations mdps_proc_calibrate_mouse_fops =
+{
+ .owner = THIS_MODULE,
+ .open = mdps_proc_calibrate_mouse_open,
+ .write = mdps_write_calibrate_mouse,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static const struct file_operations mdps_proc_rate_fops =
+{
+ .owner = THIS_MODULE,
+ .open = mdps_proc_rate_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+#endif // CONFIG_PROCFS
+
+void mdps_mouse_enable(void)
+{
+ if (mdps.idev)
+ return;
+
+ mdps.idev = input_allocate_device();
+ if (!mdps.idev)
+ return;
+
+ mdps_calibrate_mouse();
+
+ mdps.idev->name = "HP Mobile Data Protection System";
+ mdps.idev->id.bustype = BUS_I2C;
+ mdps.idev->id.vendor = 0;
+
+ input_set_abs_params(mdps.idev, ABS_X, -2048, 2048, 3, 0);
+ input_set_abs_params(mdps.idev, ABS_Y, -2048, 2048, 3, 0);
+
+ set_bit(EV_ABS, mdps.idev->evbit);
+ set_bit(EV_KEY, mdps.idev->evbit);
+ set_bit(BTN_TOUCH, mdps.idev->keybit);
+
+ if (input_register_device(mdps.idev)) {
+ input_free_device(mdps.idev);
+ mdps.idev = NULL;
+ return;
+ }
+
+ mdps.kthread = kthread_run(mdps_mouse_kthread, NULL, "kmdps");
+ if (IS_ERR(mdps.kthread)) {
+ input_unregister_device(mdps.idev);
+ mdps.idev = NULL;
+ return;
+ }
+
+ mouse = 1;
+
+#ifdef CONFIG_PROC_FS
+ {
+ struct proc_dir_entry *ent;
+ ent = create_proc_entry("calibrate_mouse", S_IWUSR, mdps.dir);
+ if (!ent)
+ {
+ return;
+ }
+
+ ent->proc_fops = &mdps_proc_calibrate_mouse_fops;
+ }
+#endif
+}
+
+void mdps_mouse_disable(void)
+{
+ if (!mdps.idev)
+ return;
+
+ kthread_stop(mdps.kthread);
+
+ input_unregister_device(mdps.idev);
+ mdps.idev = NULL;
+
+#ifdef CONFIG_PROC_FS
+ remove_proc_entry("calibrate_mouse", mdps.dir);
+#endif
+}
+
+int mdps_add_fs(struct acpi_device *device)
+{
+#ifdef CONFIG_PROC_FS
+ struct proc_dir_entry *ent;
+
+ mdps.dir = proc_mkdir(MDPS_PROC_ROOT, NULL);
+ if (!mdps.dir)
+ return -ENOMEM;
+
+ ent = create_proc_entry("position", S_IFREG | S_IRUGO, mdps.dir);
+ if (!ent)
+ return -ENOMEM;
+
+ ent->proc_fops = &mdps_proc_position_fops;
+
+ ent = create_proc_entry("state", S_IFREG | S_IRUGO | S_IWUSR, mdps.dir);
+ if (!ent)
+ return -ENOMEM;
+
+ ent->proc_fops = &mdps_proc_state_fops;
+
+ ent = create_proc_entry("rate", S_IFREG | S_IRUGO, mdps.dir);
+ if (!ent)
+ return -ENOMEM;
+
+ ent->proc_fops = &mdps_proc_rate_fops;
+
+ ent = create_proc_entry("mouse", S_IFREG | S_IRUGO | S_IWUSR, mdps.dir);
+ if (!ent)
+ return -ENOMEM;
+
+ ent->proc_fops = &mdps_proc_mouse_fops;
+#endif
+
+ return 0;
+}
+
+int mdps_remove_fs(void)
+{
+#ifdef CONFIG_PROC_FS
+ remove_proc_entry("position", mdps.dir);
+ remove_proc_entry("state", mdps.dir);
+ remove_proc_entry("rate", mdps.dir);
+ remove_proc_entry("mouse", mdps.dir);
+ remove_proc_entry(MDPS_PROC_ROOT, NULL);
+#endif
+
+ return 0;
+}
+
+static int __init mdps_init_module(void)
+{
+ int ret;
+ acpi_status status;
+ acpi_handle handle = 0;
+
+ if (acpi_disabled)
+ return -ENODEV;
+
+ // device detection: see if our device is present
+ status = acpi_get_handle(NULL, "\\_SB.C002.ACEL", &handle);
+ if (ACPI_FAILURE(status)) {
+ printk(KERN_INFO "mdps: HP Mobile Data Protection System 3D device not found\n");
+ return -ENODEV;
+ }
+
+ ret = acpi_bus_register_driver(&mdps_driver);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static void __exit mdps_exit_module(void)
+{
+ mdps_remove(mdps.device, 1);
+
+ acpi_bus_unregister_driver(&mdps_driver);
+}
+
+module_init(mdps_init_module);
+module_exit(mdps_exit_module);
--
Andrey Panin | Linux and UNIX system administrator
pazke@...pac.ru | PGP key: wwwkeys.pgp.net
Download attachment "signature.asc" of type "application/pgp-signature" (190 bytes)
Powered by blists - more mailing lists