Date:	Tue, 02 Jan 2007 22:57:17 +0000
From:	Sid Boyce <g3vbv@...eyonder.co.uk>
To:	Len Brown <lenb@...nel.org>
CC:	linux-kernel@...r.kernel.org, netdev@...r.kernel.org,
	linux-acpi@...r.kernel.org
Subject: Re: 2.6.19 and up to 2.6.20-rc2 Ethernet problems x86_64

Len Brown wrote:
> On Tuesday 02 January 2007 10:41, Sid Boyce wrote:
>   
>> Same problem with 2.6.19-rc3.
>>     
>
> Do you mean 2.6.20-rc3 still does not work?
> What was the last kernel that worked properly with no cmdline parameters?
>
>   
That's correct, same problem with 2.6.20-rc3. Last worked with 
2.6.19-rc6-git12, so it was 2.6.19 where it failed.
>> Apologies for the long spiel, if memory serves me correct, gzip'd 
>> attachments are verboten.
>>     
>
> Bugzilla may be a good place to put more information.
> If the system fails in ACPI mode, but works in non-ACPI mode,
> then please file a bug here:
> http://bugzilla.kernel.org/enter_bug.cgi?product=ACPI
>
>   
Will do.

> and attach the complete dmesg -s64000 for the last working, plus
> failing kernel -- along with /proc/interrupts for both, and a single
> copy of lspci -vv output.
>
>
>   
>> openSUSE 10.2
>> Network does not get configured with "acpi=noirq" or "acpi=off".
>>     
>
> Do you mean it does not work when running in ACPI mode, but it does
> work correctly if you boot with "acpi=noirq" or "acpi=off"?
>
> If so, please include the dmesg -s64000 and /proc/interrupts for
> the acpi=off case also.
>
>   
Attaching both case1 normal, case2 acpi=noirq. With acpi=noirq ethernet 
doesn't get configured, route -n says it's an Unsupported operation, 
ifconfig only shows for localhost, ifconfig eth0 192.168.10.5 also 
complains of a config error.

> Nothing jumps out as incorrect with the ACPI IRQ routing below.
>
> Maybe somebody who knows about the tg3 can suggest what
> the error messages mean and if they are related to interrupt
> problems, or perhaps something else like IO resource issues?
>
> -Len
>
>   
It's just not a tg3 problem, the problem is also on  nVidia Corporation 
MCP51 Ethernet Controller (rev a1) - tg3 for the 64-bit laptop and MCP51 
on the 64x2 box, tg3 and forcedeth drivers respectively.
>> There may be something in dmesg that allows further analysis of the 
>> problem.
>> 00:0a:e4:4e:a1:42 is the laptop MAC address.
>> 00:48:54:d0:22:f0 is the firewall box
>> 00:50:22:40:0F:D2 is a local box
>> Some things in dmesg which look decidedly strange when compared to what 
>> is seen with 2.6.18.2-34, two mac addresses strung together with an 
>> additional :08:00. I'm guessing here, this may be normal but I haven't 
>> seen such before.
>> Linux version 2.6.20-rc1-git7-default (root@...cie) (gcc version 4.1.2 
>> 20061115 (prerelease) (SUSE Linux)) #4 SMP Wed Dec 20 01:17:23 GMT 2006
>> Command line: root=/dev/hda1 vga=0x317    resume=/dev/hda2 splash=silent 3
>> BIOS-provided physical RAM map:
>>  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
>>  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
>>  BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved)
>>  BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
>>  BIOS-e820: 000000001fef0000 - 000000001fefb000 (ACPI data)
>>  BIOS-e820: 000000001fefb000 - 000000001ff00000 (ACPI NVS)
>>  BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
>>  BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
>> Entering add_active_range(0, 0, 159) 0 entries of 3200 used
>> Entering add_active_range(0, 256, 130800) 1 entries of 3200 used
>> end_pfn_map = 1048576
>> DMI 2.3 present.
>> ACPI: RSDP (v000 PTLTD                                 ) @ 
>> 0x00000000000f68c0
>> ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 
>> 0x000000001fef5d48
>> ACPI: FADT (v002 AMDK8  PTLTW    0x06040000 PTL_ 0x000f4240) @ 
>> 0x000000001fefae56
>> ACPI: SSDT (v001 PTLTD  POWERNOW 0x06040000  LTP 0x00000001) @ 
>> 0x000000001fefaeda
>> ACPI: MADT (v001 PTLTD           APIC   0x06040000  LTP 0x00000000) @ 
>> 0x000000001fefafb0
>> ACPI: DSDT (v001  VIA   PTL_ACPI 0x06040000 MSFT 0x0100000e) @ 
>> 0x0000000000000000
>> Scanning NUMA topology in Northbridge 24
>> Number of nodes 1
>> Node 0 MemBase 0000000000000000 Limit 000000001fef0000
>> Entering add_active_range(0, 0, 159) 0 entries of 3200 used
>> Entering add_active_range(0, 256, 130800) 1 entries of 3200 used
>> NUMA: Using 63 for the hash shift.
>> Using node hash shift of 63
>> Bootmem setup node 0 0000000000000000-000000001fef0000
>> Zone PFN ranges:
>>   DMA             0 ->     4096
>>   DMA32        4096 ->  1048576
>>   Normal    1048576 ->  1048576
>> early_node_map[2] active PFN ranges
>>     0:        0 ->      159
>>     0:      256 ->   130800
>> On node 0 totalpages: 130703
>>   DMA zone: 56 pages used for memmap
>>   DMA zone: 1183 pages reserved
>>   DMA zone: 2760 pages, LIFO batch:0
>>   DMA32 zone: 1732 pages used for memmap
>>   DMA32 zone: 124972 pages, LIFO batch:31
>>   Normal zone: 0 pages used for memmap
>> ACPI: PM-Timer IO Port: 0x4008
>> ACPI: Local APIC address 0xfee00000
>> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>> Processor #0 (Bootup-CPU)
>> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>> ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
>> IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
>> ACPI: IRQ0 used by override.
>> ACPI: IRQ2 used by override.
>> ACPI: IRQ9 used by override.
>> Setting APIC routing to physical flat
>> Using ACPI (MADT) for SMP configuration information
>> Nosave address range: 000000000009f000 - 00000000000a0000
>> Nosave address range: 00000000000a0000 - 00000000000d8000
>> Nosave address range: 00000000000d8000 - 0000000000100000
>> Allocating PCI resources starting at 30000000 (gap: 20000000:dffe0000)
>> SMP: Allowing 1 CPUs, 0 hotplug CPUs
>> PERCPU: Allocating 49664 bytes of per cpu data
>> Built 1 zonelists.  Total pages: 127732
>> Kernel command line: root=/dev/hda1 vga=0x317    resume=/dev/hda2 
>> splash=silent 3
>> Initializing CPU#0
>> PID hash table entries: 2048 (order: 11, 16384 bytes)
>> Console: colour dummy device 80x25
>> Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
>> Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
>> Checking aperture...
>> CPU 0: aperture @ e0000000 size 256 MB
>> Memory: 507156k/523200k available (1948k kernel code, 15656k reserved, 
>> 950k data, 324k init)
>> Calibrating delay using timer specific routine.. 3591.92 BogoMIPS 
>> (lpj=1795961)
>> Security Framework v1.0.0 initialized
>> Mount-cache hash table entries: 256
>> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>> CPU: L2 Cache: 1024K (64 bytes/line)
>> CPU 0/0 -> Node 0
>> SMP alternatives: switching to UP code
>> Freeing SMP alternatives: 28k freed
>> ACPI: Core revision 20060707
>> Using local APIC timer interrupts.
>> result 12464666
>> Detected 12.464 MHz APIC timer.
>> Brought up 1 CPUs
>> testing NMI watchdog ... OK.
>> time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
>> time.c: Detected 1794.911 MHz processor.
>> NET: Registered protocol family 16
>> ACPI: bus type pci registered
>> PCI: Using configuration type 1
>> ACPI: Interpreter enabled
>> ACPI: Using IOAPIC for interrupt routing
>> ACPI: PCI Root Bridge [PCI0] (0000:00)
>> PCI: Probing PCI hardware (bus 00)
>> PCI quirk: region 4000-407f claimed by vt8235 PM
>> PCI quirk: region 8100-810f claimed by vt8235 SMB
>> Boot video device is 0000:01:00.0
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>> ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *9, 
>> disabled.
>> ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *10, 
>> disabled.
>> ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled.
>> ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *10, disabled.
>> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 12 14 15)
>> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 12 14 15)
>> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15)
>> Linux Plug and Play Support v0.97 (c) Adam Belay
>> pnp: PnP ACPI init
>> pnp: PnP ACPI: found 13 devices
>> PCI: Using ACPI for IRQ routing
>> PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
>> report
>> PCI: Cannot allocate resource region 0 of device 0000:00:00.0
>> agpgart: Detected AGP bridge 0
>> agpgart: AGP aperture is 256M @ 0xe0000000
>> pnp: 00:06: ioport range 0x600-0x60f has been reserved
>> pnp: 00:06: ioport range 0x1c0-0x1cf has been reserved
>> pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
>> pnp: 00:06: ioport range 0xfe10-0xfe11 could not be reserved
>> PCI: Bridge: 0000:00:01.0
>>   IO window: 2000-2fff
>>   MEM window: d0100000-d01fffff
>>   PREFETCH window: d8000000-dfffffff
>> PCI: Bus 2, cardbus bridge: 0000:00:0b.0
>>   IO window: 00001c00-00001cff
>>   IO window: 00003000-000030ff
>>   PREFETCH window: 30000000-31ffffff
>>   MEM window: 32000000-33ffffff
>> PCI: Bus 6, cardbus bridge: 0000:00:0b.1
>>   IO window: 00003400-000034ff
>>   IO window: 00003800-000038ff
>>   PREFETCH window: 34000000-35ffffff
>>   MEM window: 36000000-37ffffff
>> PCI: Setting latency timer of device 0000:00:01.0 to 64
>> ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 17
>> PCI: Setting latency timer of device 0000:00:0b.0 to 64
>> PCI: Enabling device 0000:00:0b.1 (0000 -> 0003)
>> ACPI: PCI Interrupt 0000:00:0b.1[B] -> GSI 18 (level, low) -> IRQ 18
>> PCI: Setting latency timer of device 0000:00:0b.1 to 64
>> NET: Registered protocol family 2
>> IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
>> TCP established hash table entries: 16384 (order: 6, 262144 bytes)
>> TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
>> TCP: Hash tables configured (established 16384 bind 8192)
>> TCP reno registered
>> checking if image is initramfs... it is
>> Freeing initrd memory: 2885k freed
>> audit: initializing netlink socket (disabled)
>> audit(1166585213.510:1): initialized
>> Total HugeTLB memory allocated, 0
>> VFS: Disk quotas dquot_6.5.1
>> Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
>> io scheduler noop registered
>> io scheduler anticipatory registered
>> io scheduler deadline registered
>> io scheduler cfq registered (default)
>> vesafb: framebuffer at 0xd8000000, mapped to 0xffffc20000180000, using 
>> 3072k, total 65536k
>> vesafb: mode is 1024x768x16, linelength=2048, pages=41
>> vesafb: scrolling: redraw
>> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>> Console: switching to colour frame buffer device 128x48
>> fb0: VESA VGA frame buffer device
>> Real Time Clock Driver v1.12ac
>> Non-volatile memory driver v1.2
>> Linux agpgart interface v0.101 (c) Dave Jones
>> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
>> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>> RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
>> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
>> i8042.c: Detected active multiplexing controller, rev 1.1.
>> serio: i8042 KBD port at 0x60,0x64 irq 1
>> serio: i8042 AUX0 port at 0x60,0x64 irq 12
>> serio: i8042 AUX1 port at 0x60,0x64 irq 12
>> serio: i8042 AUX2 port at 0x60,0x64 irq 12
>> serio: i8042 AUX3 port at 0x60,0x64 irq 12
>> mice: PS/2 mouse device common for all mice
>> input: AT Translated Set 2 keyboard as /class/input/input0
>> input: PC Speaker as /class/input/input1
>> Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
>> input: SynPS/2 Synaptics TouchPad as /class/input/input2
>> NET: Registered protocol family 1
>> ACPI: (supports S0 S3 S4 S5)
>> Freeing unused kernel memory: 324k freed
>> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>> ACPI: Thermal Zone [THRS] (53 C)
>> ACPI: Thermal Zone [THRC] (78 C)
>> VP_IDE: IDE controller at PCI slot 0000:00:11.1
>> ACPI: Unable to derive IRQ for device 0000:00:11.1
>> Losing some ticks... checking if CPU frequency changed.
>> ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
>> VP_IDE: chipset revision 6
>> VP_IDE: not 100% native mode: will probe irqs later
>> VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
>>     ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio
>>     ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio
>> Probing IDE interface ide0...
>> hda: WDC WD800VE-07HDT0, ATA DISK drive
>> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>> hda: max request size: 128KiB
>> hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, 
>> UDMA(100)
>> hda: cache flushes supported
>>  hda: hda1 hda2
>> Probing IDE interface ide1...
>> hdc: _NEC DVD_RW ND-6750A, ATAPI CD/DVD-ROM drive
>> ide1 at 0x170-0x177,0x376 on irq 15
>> BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
>> Attempting manual resume
>> ReiserFS: hda1: found reiserfs format "3.6" with standard journal
>> ReiserFS: hda1: using ordered data mode
>> ReiserFS: hda1: journal params: device hda1, size 8192, journal first 
>> block 18, max trans len 1024, max batch 900, max commit age 30, max 
>> trans age 30
>> ReiserFS: hda1: checking transaction log (hda1)
>> ReiserFS: hda1: Using r5 hash to sort names
>> NET: Registered protocol family 23
>> usbcore: registered new interface driver usbfs
>> usbcore: registered new interface driver hub
>> usbcore: registered new device driver usb
>> Yenta: CardBus bridge found at 0000:00:0b.0 [1025:0046]
>> USB Universal Host Controller Interface driver v3.0
>> ieee1394: Initialized config rom entry `ip1394'
>> Yenta: ISA IRQ mask 0x00b8, PCI irq 17
>> Socket status: 30000410
>> Yenta: CardBus bridge found at 0000:00:0b.1 [1025:0046]
>> Yenta: ISA IRQ mask 0x00b8, PCI irq 18
>> Socket status: 30000820
>> ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
>> uhci_hcd 0000:00:10.0: UHCI Host Controller
>> uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
>> uhci_hcd 0000:00:10.0: irq 21, io base 0x00001020
>> usb usb1: configuration #1 chosen from 1 choice
>> hub 1-0:1.0: USB hub found
>> hub 1-0:1.0: 2 ports detected
>> ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 21
>> uhci_hcd 0000:00:10.1: UHCI Host Controller
>> uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
>> uhci_hcd 0000:00:10.1: irq 21, io base 0x00001040
>> usb usb2: configuration #1 chosen from 1 choice
>> hub 2-0:1.0: USB hub found
>> hub 2-0:1.0: 2 ports detected
>> ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 21
>> uhci_hcd 0000:00:10.2: UHCI Host Controller
>> uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
>> uhci_hcd 0000:00:10.2: irq 21, io base 0x00001060
>> usb usb3: configuration #1 chosen from 1 choice
>> pccard: PCMCIA card inserted into slot 0
>> hub 3-0:1.0: USB hub found
>> hub 3-0:1.0: 2 ports detected
>> usb 1-2: new full speed USB device using uhci_hcd and address 2
>> nsc-ircc, chip->init
>> nsc-ircc, Found chip at base=0x02e
>> nsc-ircc, driver loaded (Dag Brattli)
>> ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 21
>> ehci_hcd 0000:00:10.3: EHCI Host Controller
>> ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
>> ehci_hcd 0000:00:10.3: irq 21, io mem 0xd0000800
>> ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>> usb usb4: configuration #1 chosen from 1 choice
>> hub 4-0:1.0: USB hub found
>> hub 4-0:1.0: 6 ports detected
>> nsc_ircc_open(), can't get iobase of 0x2f8
>> nsc-ircc, Found chip at base=0x02e
>> nsc-ircc, driver loaded (Dag Brattli)
>> nsc_ircc_open(), can't get iobase of 0x2f8
>> pnp: Device 00:0a disabled.
>> pccard: CardBus card inserted into slot 1
>> ACPI: PCI Interrupt 0000:00:0b.2[C] -> GSI 19 (level, low) -> IRQ 19
>> ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] 
>> MMIO=[d0000000-d00007ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
>> ---------------------------------------------------------------------
>> tg3.c:v3.71 (December 15, 2006)
>> ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 20 (level, low) -> IRQ 20
>> eth0: Tigon3 [partno(BCM95705A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 
>> 10/100/1000Base-T Ethernet 00:0a:e4:4e:a1:42
>> ------------------------------------------------------------------------
>> eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] 
>> TSOcap[1]
>> eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
>> ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
>> PCI: Setting latency timer of device 0000:00:11.5 to 64
>> hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
>> Uniform CD-ROM driver Revision: 3.20
>> usb 1-2: device not accepting address 2, error -71
>> parport: PnPBIOS parport detected.
>> parport0: PC-style at 0x378 (0x778), irq 7, dma 3 
>> [PCSPP,TRISTATE,COMPAT,ECP,DMA]
>> wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.6
>> wbsd: Copyright(c) Pierre Ossman
>> mmc0: W83L51xD id 7112 at 0x820 irq 10 FIFO PnP
>> ieee1394: Host added: ID:BUS[0-00:1023]  GUID[000ae404061046b5]
>> cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xd3fff 
>> 0xd8000-0xdffff 0xe4000-0xfffff
>> cs: memory probe 0x60000000-0x60ffffff: clean.
>> cs: memory probe 0xa0000000-0xa0ffffff: clean.
>> pcmcia: registering new device pcmcia0.0
>> usb 1-2: new full speed USB device using uhci_hcd and address 4
>> pcmcia: request for exclusive IRQ could not be fulfilled.
>> pcmcia: the driver needs updating to supported shared IRQ lines.
>> 0.0: ttyS0 at I/O 0x3f8 (irq = 17) is a 16550A
>> usb 1-2: configuration #1 chosen from 1 choice
>> Bluetooth: Core ver 2.11
>> NET: Registered protocol family 31
>> Bluetooth: HCI device and connection manager initialized
>> Bluetooth: HCI socket layer initialized
>> usb 3-1: new full speed USB device using uhci_hcd and address 2
>> Bluetooth: HCI USB driver ver 2.9
>> usb 3-1: configuration #1 chosen from 1 choice
>> hub 3-1:1.0: USB hub found
>> hub 3-1:1.0: 4 ports detected
>> usb 3-2: new low speed USB device using uhci_hcd and address 3
>> usb 3-2: configuration #1 chosen from 1 choice
>> usbcore: registered new interface driver hci_usb
>> usb 2-1: new full speed USB device using uhci_hcd and address 2
>> usb 2-1: configuration #1 chosen from 1 choice
>> usb 3-1.3: new full speed USB device using uhci_hcd and address 4
>> Bluetooth: L2CAP ver 2.8
>> Bluetooth: L2CAP socket layer initialized
>> usb 3-1.3: not running at top speed; connect to a high speed hub
>> Bluetooth: HIDP (Human Interface Emulation) ver 1.1
>> usb 3-1.3: configuration #1 chosen from 1 choice
>> usbcore: registered new interface driver hiddev
>> input: Acrox USB & PS/2 Mouse as /class/input/input3
>> input: USB HID v1.10 Mouse [Acrox USB & PS/2 Mouse] on usb-0000:00:10.2-2
>> usbcore: registered new interface driver usbhid
>> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>> usbcore: registered new interface driver usbserial
>> drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
>> usbcore: registered new interface driver usbserial_generic
>> drivers/usb/serial/usb-serial.c: USB Serial Driver core
>> drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
>> pl2303 2-1:1.0: pl2303 converter detected
>> usb 2-1: pl2303 converter now attached to ttyUSB0
>> usbcore: registered new interface driver pl2303
>> drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
>> SCSI subsystem initialized
>> Initializing USB Mass Storage driver...
>> scsi0 : SCSI emulation for USB Mass Storage devices
>> usb-storage: device found at 4
>> usb-storage: waiting for device to settle before scanning
>> usbcore: registered new interface driver usb-storage
>> Bluetooth: RFCOMM socket layer initialized
>> Bluetooth: RFCOMM TTY layer initialized
>> Bluetooth: RFCOMM ver 1.8
>> USB Mass Storage support registered.
>> Bluetooth: BNEP (Ethernet Emulation) ver 1.2
>> Bluetooth: BNEP filters: protocol multicast
>> Adding 3931696k swap on /dev/hda2.  Priority:-1 extents:1 across:3931696k
>> device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: 
>> dm-devel@...hat.com
>> loop: loaded (max 8 devices)
>> scsi 0:0:0:0: Direct-Access     Maxtor 6 Y120L0           YAR4 PQ: 0 
>> ANSI: 0
>> usb-storage: device scan complete
>> SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
>> sda: Write Protect is off
>> sda: Mode Sense: 03 00 00 00
>> sda: assuming drive cache: write through
>> SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
>> sda: Write Protect is off
>> sda: Mode Sense: 03 00 00 00
>> sda: assuming drive cache: write through
>>  sda: sda1 sda2
>> sd 0:0:0:0: Attached scsi disk sda
>> sd 0:0:0:0: Attached scsi generic sg0 type 0
>> Adding 1550264k swap on /dev/sda2.  Priority:-2 extents:1 across:1550264k
>> NET: Registered protocol family 10
>> lo: Disabled Privacy Extensions
>> ip6_tables: (C) 2000-2006 Netfilter Core Team
>> ip_tables: (C) 2000-2006 Netfilter Core Team
>> ACPI: AC Adapter [AC] (on-line)
>> ACPI: Battery Slot [BAT0] (battery present)
>> ACPI: Power Button (FF) [PWRF]
>> ACPI: Lid Switch [LID]
>> ACPI: Sleep Button (CM) [SLPB]
>> powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors 
>> (version 2.00.00)
>> powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x2
>> powernow-k8:    1 : fid 0x8 (1600 MHz), vid 0x6
>> powernow-k8:    2 : fid 0x0 (800 MHz), vid 0x12
>> ttyS1: LSR safety check engaged!
>> audit(1166585256.326:2): audit_pid=2996 old=0 by auid=4294967295
>> PM: Writing back config space on device 0000:00:0c.0 at offset b (was 
>> 3ed173b, writing 461025)
>> PM: Writing back config space on device 0000:00:0c.0 at offset 3 (was 0, 
>> writing 4010)
>> PM: Writing back config space on device 0000:00:0c.0 at offset 2 (was 
>> 2000000, writing 2000003)
>> PM: Writing back config space on device 0000:00:0c.0 at offset 1 (was 
>> 2b00000, writing 2b00006)
>> PM: Writing back config space on device 0000:00:0c.0 at offset 0 (was 
>> 3ed173b, writing 169c14e4)
>> ADDRCONF(NETDEV_UP): eth0: link is not ready
>> NET: Registered protocol family 17
>> tg3: eth0: Link is up at 100 Mbps, full duplex.
>> tg3: eth0: Flow control is on for TX and on for RX.
>> ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=224.0.0.251 LEN=107 
>> TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.10.5 DST=224.0.0.251 
>> LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 
>> LEN=87
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=224.0.0.251 LEN=107 
>> TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.10.5 DST=224.0.0.251 
>> LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 
>> LEN=87
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=192.168.10.1 LEN=60 
>> TOS=0x00 PREC=0x00 TTL=64 ID=64687 DF PROTO=TCP SPT=14566 DPT=111 
>> WINDOW=5840 RES=0x00 S
>> YN URGP=0 OPT (020405B40402080AFFFC4A360000000001030302)
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=224.0.0.22 LEN=40 
>> TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF OPT (94040000) PROTO=2
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=224.0.0.251 LEN=107 
>> TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.10.5 DST=224.0.0.251 
>> LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 
>> LEN=87
>> eth0: no IPv6 routers present
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=192.168.10.1 LEN=60 
>> TOS=0x00 PREC=0x00 TTL=64 ID=64689 DF PROTO=TCP SPT=14566 DPT=111 
>> WINDOW=5840 RES=0x00 S
>> YN URGP=0 OPT (020405B40402080AFFFC90860000000001030302)
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=195.188.53.175 
>> DST=192.168.10.5 LEN=119 TOS=0x00 PREC=0x00 TTL=247 ID=45
>> 161 DF PROTO=UDP SPT=53 DPT=1025 LEN=99
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=195.188.53.175 
>> DST=192.168.10.5 LEN=119 TOS=0x00 PREC=0x00 TTL=247 ID=45
>> 162 DF PROTO=UDP SPT=53 DPT=1027 LEN=99
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=62.31.176.39 
>> DST=192.168.10.5 LEN=119 TOS=0x00 PREC=0x00 TTL=251 ID=1270
>> 7 DF PROTO=UDP SPT=53 DPT=1026 LEN=99
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:50:22:40:0f:d2:08:00 SRC=192.168.10.1 
>> DST=192.168.10.5 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=47744
>> PROTO=ICMP TYPE=0 CODE=0 ID=34575 SEQ=1
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:50:22:40:0f:d2:08:00 SRC=192.168.10.1 
>> DST=192.168.10.5 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=47745
>> PROTO=ICMP TYPE=0 CODE=0 ID=34575 SEQ=2
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=194.117.134.19 
>> DST=192.168.10.5 LEN=119 TOS=0x00 PREC=0x00 TTL=248 ID=56
>> 11 DF PROTO=UDP SPT=53 DPT=1028 LEN=99
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:50:22:40:0f:d2:08:00 SRC=192.168.10.1 
>> DST=192.168.10.5 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=47746
>> PROTO=ICMP TYPE=0 CODE=0 ID=34575 SEQ=3
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:50:22:40:0f:d2:08:00 SRC=192.168.10.1 
>> DST=192.168.10.5 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=47747
>> PROTO=ICMP TYPE=0 CODE=0 ID=34575 SEQ=4
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=62.31.176.39 
>> DST=192.168.10.5 LEN=119 TOS=0x00 PREC=0x00 TTL=251 ID=1270
>> 8 DF PROTO=UDP SPT=53 DPT=1029 LEN=99
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:50:22:40:0f:d2:08:00 SRC=192.168.10.1 
>> DST=192.168.10.5 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=47748
>> PROTO=ICMP TYPE=0 CODE=0 ID=34575 SEQ=5
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=195.188.53.175 LEN=58 
>> TOS=0x00 PREC=0x00 TTL=64 ID=43443 DF PROTO=UDP SPT=1025 DPT=53 LEN=38
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=194.117.134.19 
>> DST=192.168.10.5 LEN=119 TOS=0x00 PREC=0x00 TTL=248 ID=56
>> 13 DF PROTO=UDP SPT=53 DPT=1028 LEN=99
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=194.117.134.19 LEN=63 
>> TOS=0x00 PREC=0x00 TTL=64 ID=13907 DF PROTO=UDP SPT=1034 DPT=53 LEN=43
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=194.117.134.19 
>> DST=192.168.10.5 LEN=138 TOS=0x00 PREC=0x00 TTL=248 ID=56
>> 16 DF PROTO=UDP SPT=53 DPT=1036 LEN=118
>> SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.10.5 DST=194.117.134.19 LEN=63 
>> TOS=0x00 PREC=0x00 TTL=64 ID=18909 DF PROTO=UDP SPT=1036 DPT=53 LEN=43
>> SFW2-INext-DROP-DEFLT IN=eth0 OUT= 
>> MAC=00:0a:e4:4e:a1:42:00:48:54:d0:22:f0:08:00 SRC=195.188.53.175 
>> DST=192.168.10.5 LEN=74 TOS=0x00 PREC=0x00 TTL=247 ID=356
>> 16 DF PROTO=UDP SPT=53 DPT=1039 LEN=54
>> etc.,etc.
>>
>> Regards
>> Sid.
>>
>>     
>
>
>   
Regards
Sid.

-- 
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks


View attachment "ETH_ERR_with_ACPI" of type "text/plain" (38452 bytes)

View attachment "ETH_ERR_noacpi" of type "text/plain" (30782 bytes)

Powered by blists - more mailing lists