lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite for Android: free password hash cracker in your pocket
[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Date:	Fri, 27 Jun 2008 21:00:37 -0500
From:	Jay Cliburn <jacliburn@...lsouth.net>
To:	Jie Yang <Jie.Yang@...eros.com>
Cc:	"jeff@...zik.org" <jeff@...zik.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	"netdev@...r.kernel.org" <netdev@...r.kernel.org>
Subject: Re: [PATCH 2.6.25.3 3/5] atl1e: Atheros L1E Gigabit Ethernet driver

On Thu, 26 Jun 2008 13:38:00 +0800
Jie Yang <Jie.Yang@...eros.com> wrote:

> From: Jie Yang <jie.yang@...eros.com>
> 
> Full patch for the Atheros L1E Gigabit Ethernet driver.
> Supportring AR8121, AR8113 and AR8114
> 
> Signed-off-by: Jie Yang <jie.yang @atheros.com>
> ---
> diff -uprN -X linux-2.6.25.3.orig/Documentation/dontdiff
> linux-2.6.25.3.orig/drivers/net/atl1e/atl1e_hw.h
> linux-2.6.25.3.atheros/drivers/net/atl1e/atl1e_hw.h ---
> linux-2.6.25.3.orig/drivers/net/atl1e/atl1e_hw.h    1970-01-01
> 08:00:00.000000000 +0800 +++
> linux-2.6.25.3.atheros/drivers/net/atl1e/atl1e_hw.h 2008-06-20
> 11:22:34.000000000 +0800 @@ -0,0 +1,1116 @@ +/*
> + * Copyright(c) 2007 Atheros Corporation. All rights reserved.
> + *
> + * Derived from Intel e1000 driver
> + * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or
> modify it
> + * under the terms of the GNU General Public License as published by
> the Free
> + * Software Foundation; either version 2 of the License, or (at your
> option)
> + * any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public
> License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License
> along with
> + * this program; if not, write to the Free Software Foundation,
> Inc., 59
> + * Temple Place - Suite 330, Boston, MA  02111-1307, USA.
> + *
> + * There are a lot of defines in here that are unused and/or have
> cryptic
> + * names.  Please leave them alone, as they're the closest thing we
> have
> + * to a spec from Atheros at present. *ahem* -- CHS
> + */

Cut/paste artifact?

> +
> +#ifndef _ATHEROS_HW_H__
> +#define _ATHEROS_HW_H__
> +
> +#include "atl1e_osdep.h"
> +
> +struct atl1e_adapter;
> +struct atl1e_hw;
> +
> +/* function prototype */

Reorder code to minimize forward declarations.

> +s32 atl1e_reset_hw(struct atl1e_hw *hw);
> +s32 atl1e_read_mac_addr(struct atl1e_hw *hw);
> +s32 atl1e_init_hw(struct atl1e_hw *hw);
> +s32 atl1e_phy_commit(struct atl1e_hw *hw);
> +s32 atl1e_get_speed_and_duplex(struct atl1e_hw *hw, u16 *speed, u16
> *duplex); +u32 atl1e_auto_get_fc(struct atl1e_adapter *adapter, u16
> duplex); +u32 atl1e_hash_mc_addr(struct atl1e_hw *hw, u8 *mc_addr);
> +void atl1e_hash_set(struct atl1e_hw *hw, u32 hash_value);
> +s32 atl1e_read_phy_reg(struct atl1e_hw *hw, u16 reg_addr, u16
> *phy_data); +s32 atl1e_write_phy_reg(struct atl1e_hw *hw, u32
> reg_addr, u16 phy_data); +void atl1e_read_pci_cfg(struct atl1e_hw
> *hw, u32 reg, u16 *value); +void atl1e_write_pci_cfg(struct atl1e_hw
> *hw, u32 reg, u16 *value); +s32 atl1e_validate_mdi_setting(struct
> atl1e_hw *hw); +void set_mac_addr(struct atl1e_hw *hw);
> +bool read_eeprom(struct atl1e_hw *hw, u32 offset, u32 *p_value);
> +bool write_eeprom(struct atl1e_hw *hw, u32 offset, u32 value);
> +s32 atl1e_phy_enter_power_saving(struct atl1e_hw *hw);
> +s32 atl1e_phy_leave_power_saving(struct atl1e_hw *hw);
> +s32 atl1e_phy_init(struct atl1e_hw *hw);
> +int check_eeprom_exist(struct atl1e_hw *hw);
> +void atl1e_force_ps(struct atl1e_hw *hw);
> +s32 atl1e_restart_autoneg(struct atl1e_hw *hw);
> +
> +/* register definition */
> +#define REG_PM_CTRLSTAT             0x44
> +
> +#define REG_PCIE_CAP_LIST           0x58
> +
> +#define REG_DEVICE_CAP              0x5C
> +#define     DEVICE_CAP_MAX_PAYLOAD_MASK     0x7
> +#define     DEVICE_CAP_MAX_PAYLOAD_SHIFT    0
> +
> +#define REG_DEVICE_CTRL             0x60
> +#define     DEVICE_CTRL_MAX_PAYLOAD_MASK    0x7
> +#define     DEVICE_CTRL_MAX_PAYLOAD_SHIFT   5
> +#define     DEVICE_CTRL_MAX_RREQ_SZ_MASK    0x7
> +#define     DEVICE_CTRL_MAX_RREQ_SZ_SHIFT   12
> +
> +#define REG_VPD_CAP                 0x6C
> +#define     VPD_CAP_ID_MASK                 0xff
> +#define     VPD_CAP_ID_SHIFT                0
> +#define     VPD_CAP_NEXT_PTR_MASK           0xFF
> +#define     VPD_CAP_NEXT_PTR_SHIFT          8
> +#define     VPD_CAP_VPD_ADDR_MASK           0x7FFF
> +#define     VPD_CAP_VPD_ADDR_SHIFT          16
> +#define     VPD_CAP_VPD_FLAG                0x80000000
> +
> +#define REG_VPD_DATA                0x70
> +
> +#define REG_SPI_FLASH_CTRL          0x200
> +#define     SPI_FLASH_CTRL_STS_NON_RDY      0x1
> +#define     SPI_FLASH_CTRL_STS_WEN          0x2
> +#define     SPI_FLASH_CTRL_STS_WPEN         0x80
> +#define     SPI_FLASH_CTRL_DEV_STS_MASK     0xFF
> +#define     SPI_FLASH_CTRL_DEV_STS_SHIFT    0
> +#define     SPI_FLASH_CTRL_INS_MASK         0x7
> +#define     SPI_FLASH_CTRL_INS_SHIFT        8
> +#define     SPI_FLASH_CTRL_START            0x800
> +#define     SPI_FLASH_CTRL_EN_VPD           0x2000
> +#define     SPI_FLASH_CTRL_LDSTART          0x8000
> +#define     SPI_FLASH_CTRL_CS_HI_MASK       0x3
> +#define     SPI_FLASH_CTRL_CS_HI_SHIFT      16
> +#define     SPI_FLASH_CTRL_CS_HOLD_MASK     0x3
> +#define     SPI_FLASH_CTRL_CS_HOLD_SHIFT    18
> +#define     SPI_FLASH_CTRL_CLK_LO_MASK      0x3
> +#define     SPI_FLASH_CTRL_CLK_LO_SHIFT     20
> +#define     SPI_FLASH_CTRL_CLK_HI_MASK      0x3
> +#define     SPI_FLASH_CTRL_CLK_HI_SHIFT     22
> +#define     SPI_FLASH_CTRL_CS_SETUP_MASK    0x3
> +#define     SPI_FLASH_CTRL_CS_SETUP_SHIFT   24
> +#define     SPI_FLASH_CTRL_EROM_PGSZ_MASK   0x3
> +#define     SPI_FLASH_CTRL_EROM_PGSZ_SHIFT  26
> +#define     SPI_FLASH_CTRL_WAIT_READY       0x10000000
> +
> +#define REG_SPI_ADDR                0x204
> +
> +#define REG_SPI_DATA                0x208
> +
> +#define REG_SPI_FLASH_CONFIG        0x20C
> +#define     SPI_FLASH_CONFIG_LD_ADDR_MASK   0xFFFFFF
> +#define     SPI_FLASH_CONFIG_LD_ADDR_SHIFT  0
> +#define     SPI_FLASH_CONFIG_VPD_ADDR_MASK  0x3
> +#define     SPI_FLASH_CONFIG_VPD_ADDR_SHIFT 24
> +#define     SPI_FLASH_CONFIG_LD_EXIST       0x4000000
> +
> +
> +#define REG_SPI_FLASH_OP_PROGRAM    0x210
> +#define REG_SPI_FLASH_OP_SC_ERASE   0x211
> +#define REG_SPI_FLASH_OP_CHIP_ERASE 0x212
> +#define REG_SPI_FLASH_OP_RDID       0x213
> +#define REG_SPI_FLASH_OP_WREN       0x214
> +#define REG_SPI_FLASH_OP_RDSR       0x215
> +#define REG_SPI_FLASH_OP_WRSR       0x216
> +#define REG_SPI_FLASH_OP_READ       0x217
> +
> +#define REG_TWSI_CTRL               0x218
> +#define     TWSI_CTRL_LD_OFFSET_MASK        0xFF
> +#define     TWSI_CTRL_LD_OFFSET_SHIFT       0
> +#define     TWSI_CTRL_LD_SLV_ADDR_MASK      0x7
> +#define     TWSI_CTRL_LD_SLV_ADDR_SHIFT     8
> +#define     TWSI_CTRL_SW_LDSTART            0x800
> +#define     TWSI_CTRL_HW_LDSTART            0x1000
> +#define     TWSI_CTRL_SMB_SLV_ADDR_MASK     0x0x7F
> +#define     TWSI_CTRL_SMB_SLV_ADDR_SHIFT    15
> +#define     TWSI_CTRL_LD_EXIST              0x400000
> +#define     TWSI_CTRL_READ_FREQ_SEL_MASK    0x3
> +#define     TWSI_CTRL_READ_FREQ_SEL_SHIFT   23
> +#define     TWSI_CTRL_FREQ_SEL_100K         0
> +#define     TWSI_CTRL_FREQ_SEL_200K         1
> +#define     TWSI_CTRL_FREQ_SEL_300K         2
> +#define     TWSI_CTRL_FREQ_SEL_400K         3
> +#define     TWSI_CTRL_SMB_SLV_ADDR
> +#define     TWSI_CTRL_WRITE_FREQ_SEL_MASK   0x3
> +#define     TWSI_CTRL_WRITE_FREQ_SEL_SHIFT  24
> +
> +
> +#define REG_PCIE_DEV_MISC_CTRL      0x21C
> +#define     PCIE_DEV_MISC_CTRL_EXT_PIPE     0x2
> +#define     PCIE_DEV_MISC_CTRL_RETRY_BUFDIS 0x1
> +#define     PCIE_DEV_MISC_CTRL_SPIROM_EXIST 0x4
> +#define     PCIE_DEV_MISC_CTRL_SERDES_ENDIAN    0x8
> +#define     PCIE_DEV_MISC_CTRL_SERDES_SEL_DIN   0x10
> +
> +#define REG_PCIE_PHYMISC           0x1000
> +#define PCIE_PHYMISC_FORCE_RCV_DET     0x4
> +
> +#define REG_LTSSM_TEST_MODE         0x12FC
> +#define         LTSSM_TEST_MODE_DEF     0xE000
> +
> +/* Selene Master Control Register */
> +#define REG_MASTER_CTRL             0x1400
> +#define     MASTER_CTRL_SOFT_RST            0x1
> +#define     MASTER_CTRL_MTIMER_EN           0x2
> +#define     MASTER_CTRL_ITIMER_EN           0x4
> +#define     MASTER_CTRL_MANUAL_INT          0x8
> +#define     MASTER_CTRL_ITIMER2_EN          0x20
> +#define     MASTER_CTRL_INT_RDCLR           0x40
> +#define     MASTER_CTRL_LED_MODE           0x200
> +#define     MASTER_CTRL_REV_NUM_SHIFT       16
> +#define     MASTER_CTRL_REV_NUM_MASK        0xff
> +#define     MASTER_CTRL_DEV_ID_SHIFT        24
> +#define     MASTER_CTRL_DEV_ID_MASK         0xff
> +
> +/* Timer Initial Value Register */
> +#define REG_MANUAL_TIMER_INIT       0x1404
> +
> +
> +/* IRQ ModeratorTimer Initial Value Register */
> +#define REG_IRQ_MODU_TIMER_INIT     0x1408   /* w */
> +#define REG_IRQ_MODU_TIMER2_INIT    0x140A   /* w */

What does "w" mean?

> +
> +
> +#define REG_GPHY_CTRL               0x140C
> +#define     GPHY_CTRL_EXT_RESET         1
> +#define     GPHY_CTRL_PIPE_MOD          2
> +#define     GPHY_CTRL_TEST_MODE_MASK    3
> +#define     GPHY_CTRL_TEST_MODE_SHIFT   2
> +#define     GPHY_CTRL_BERT_START        0x10
> +#define     GPHY_CTRL_GATE_25M_EN       0x20
> +#define     GPHY_CTRL_LPW_EXIT          0x40
> +#define     GPHY_CTRL_PHY_IDDQ          0x80
> +#define     GPHY_CTRL_PHY_IDDQ_DIS      0x100
> +#define     GPHY_CTRL_PCLK_SEL_DIS      0x200
> +#define     GPHY_CTRL_HIB_EN            0x400
> +#define     GPHY_CTRL_HIB_PULSE         0x800
> +#define     GPHY_CTRL_SEL_ANA_RST       0x1000
> +#define     GPHY_CTRL_PHY_PLL_ON        0x2000
> +#define     GPHY_CTRL_PWDOWN_HW                0x4000
> +#define     GPHY_CTRL_DEFAULT (\
> +               GPHY_CTRL_PHY_PLL_ON    |\
> +               GPHY_CTRL_SEL_ANA_RST   |\
> +               GPHY_CTRL_HIB_PULSE     |\
> +               GPHY_CTRL_HIB_EN)
> +
> +#define     GPHY_CTRL_PW_WOL_DIS (\
> +               GPHY_CTRL_PHY_PLL_ON    |\
> +               GPHY_CTRL_SEL_ANA_RST   |\
> +               GPHY_CTRL_HIB_PULSE     |\
> +               GPHY_CTRL_HIB_EN        |\
> +               GPHY_CTRL_PWDOWN_HW     |\
> +               GPHY_CTRL_PCLK_SEL_DIS  |\
> +               GPHY_CTRL_PHY_IDDQ)
> +
> +/* IRQ Anti-Lost Timer Initial Value Register */
> +#define REG_CMBDISDMA_TIMER         0x140E
> +
> +
> +/* Block IDLE Status Register */
> +#define REG_IDLE_STATUS        0x1410
> +#define     IDLE_STATUS_RXMAC       1    /* 1: RXMAC state machine
> is in non-IDLE state. 0: RXMAC is idling */ +#define
> IDLE_STATUS_TXMAC       2    /* 1: TXMAC state machine is in non-IDLE
> state. 0: TXMAC is idling */ +#define     IDLE_STATUS_RXQ
> 4    /* 1: RXQ state machine is in non-IDLE state.   0: RXQ is
> idling   */ +#define     IDLE_STATUS_TXQ         8    /* 1: TXQ state
> machine is in non-IDLE state.   0: TXQ is idling   */ +#define
> IDLE_STATUS_DMAR        0x10 /* 1: DMAR state machine is in non-IDLE
> state.  0: DMAR is idling  */ +#define     IDLE_STATUS_DMAW
> 0x20 /* 1: DMAW state machine is in non-IDLE state.  0: DMAW is
> idling  */ +#define     IDLE_STATUS_SMB         0x40 /* 1: SMB state
> machine is in non-IDLE state.   0: SMB is idling   */ +#define
> IDLE_STATUS_CMB         0x80 /* 1: CMB state machine is in non-IDLE
> state.   0: CMB is idling   */ + +/* MDIO Control Register */
> +#define REG_MDIO_CTRL           0x1414 +#define
> MDIO_DATA_MASK          0xffff  /* On MDIO write, the 16-bit control
> data to write to PHY MII management register */ +#define
> MDIO_DATA_SHIFT         0       /* On MDIO read, the 16-bit status
> data that was read from the PHY MII management register*/
> +#define     MDIO_REG_ADDR_MASK      0x1f    /* MDIO register address
> */ +#define     MDIO_REG_ADDR_SHIFT     16 +#define
> MDIO_RW                 0x200000      /* 1: read, 0: write */
> +#define     MDIO_SUP_PREAMBLE       0x400000      /* Suppress
> preamble */ +#define     MDIO_START              0x800000      /*
> Write 1 to initiate the MDIO master. And this bit is self cleared
> after one cycle*/ +#define     MDIO_CLK_SEL_SHIFT      24
> +#define     MDIO_CLK_25_4           0 +#define
> MDIO_CLK_25_6           2 +#define     MDIO_CLK_25_8           3
> +#define     MDIO_CLK_25_10          4 +#define
> MDIO_CLK_25_14          5 +#define     MDIO_CLK_25_20          6
> +#define     MDIO_CLK_25_28          7 +#define
> MDIO_BUSY               0x8000000 +#define
> MDIO_AP_EN              0x10000000 +#define MDIO_WAIT_TIMES
> 10 + +/* MII PHY Status Register */ +#define REG_PHY_STATUS
> 0x1418 +#define     PHY_STATUS_100M          0x20000 +#define
> PHY_STATUS_EMI_CA        0x40000 + +/* BIST Control and Status
> Register0 (for the Packet Memory) */ +#define
> REG_BIST0_CTRL              0x141c +#define
> BIST0_NOW                   0x1 /* 1: To trigger BIST0 logic. This
> bit stays high during the */ +/* BIST process and reset to zero when
> BIST is done */ +#define     BIST0_SRAM_FAIL             0x2 /* 1:
> The SRAM failure is un-repairable because it has address */ +/*
> decoder failure or more than 1 cell stuck-to-x failure */
> +#define     BIST0_FUSE_FLAG             0x4 /* 1: Indicating one
> cell has been fixed */ + +/* BIST Control and Status Register1(for
> the retry buffer of PCI Express) */ +#define
> REG_BIST1_CTRL              0x1420 +#define
> BIST1_NOW                   0x1 /* 1: To trigger BIST0 logic. This
> bit stays high during the */ +/* BIST process and reset to zero when
> BIST is done */ +#define     BIST1_SRAM_FAIL             0x2 /* 1:
> The SRAM failure is un-repairable because it has address */ +/*
> decoder failure or more than 1 cell stuck-to-x failure.*/
> +#define     BIST1_FUSE_FLAG             0x4 + +/* SerDes Lock Detect
> Control and Status Register */ +#define REG_SERDES_LOCK
> 0x1424 +#define     SERDES_LOCK_DETECT          1  /* 1: SerDes lock
> detected . This signal comes from Analog SerDes */ +#define
> SERDES_LOCK_DETECT_EN       2  /* 1: Enable SerDes Lock detect
> function */ + +/* MAC Control Register  */ +#define
> REG_MAC_CTRL                0x1480 +#define
> MAC_CTRL_TX_EN              1  /* 1: Transmit Enable */ +#define
> MAC_CTRL_RX_EN              2  /* 1: Receive Enable */ +#define
> MAC_CTRL_TX_FLOW            4  /* 1: Transmit Flow Control Enable */
> +#define     MAC_CTRL_RX_FLOW            8  /* 1: Receive Flow
> Control Enable */ +#define     MAC_CTRL_LOOPBACK
> 0x10      /* 1: Loop back at G/MII Interface */ +#define
> MAC_CTRL_DUPLX              0x20      /* 1: Full-duplex mode  0:
> Half-duplex mode */ +#define     MAC_CTRL_ADD_CRC
> 0x40      /* 1: Instruct MAC to attach CRC on all egress Ethernet
> frames */ +#define     MAC_CTRL_PAD                0x80      /* 1:
> Instruct MAC to pad short frames to 60-bytes, and then attach CRC.
> This bit has higher priority over CRC_EN */ +#define
> MAC_CTRL_LENCHK             0x100     /* 1: Instruct MAC to check if
> length field matches the real packet length */ +#define
> MAC_CTRL_HUGE_EN            0x200     /* 1: receive Jumbo frame
> enable */ +#define     MAC_CTRL_PRMLEN_SHIFT       10        /*
> Preamble length */ +#define     MAC_CTRL_PRMLEN_MASK        0xf
> +#define     MAC_CTRL_RMV_VLAN           0x4000    /* 1: to remove
> VLAN Tag automatically from all receive packets */ +#define
> MAC_CTRL_PROMIS_EN          0x8000    /* 1: Promiscuous Mode Enable
> */ +#define     MAC_CTRL_TX_PAUSE           0x10000   /* 1: transmit
> test pause */ +#define     MAC_CTRL_SCNT               0x20000   /*
> 1: shortcut slot time counter */ +#define
> MAC_CTRL_SRST_TX            0x40000   /* 1: synchronized reset
> Transmit MAC module */ +#define     MAC_CTRL_TX_SIMURST
> 0x80000   /* 1: transmit simulation reset */ +#define
> MAC_CTRL_SPEED_SHIFT        20        /* 10: gigabit 01:10M/100M */
> +#define     MAC_CTRL_SPEED_MASK         0x300000 +#define
> MAC_CTRL_SPEED_1000         2 +#define
> MAC_CTRL_SPEED_10_100       1 +#define
> MAC_CTRL_DBG_TX_BKPRESURE   0x400000  /* 1: transmit maximum backoff
> (half-duplex test bit) */ +#define     MAC_CTRL_TX_HUGE
> 0x800000  /* 1: transmit huge enable */ +#define
> MAC_CTRL_RX_CHKSUM_EN       0x1000000 /* 1: RX checksum enable */
> +#define     MAC_CTRL_MC_ALL_EN          0x2000000 /* 1: upload all
> multicast frame without error to system */ +#define
> MAC_CTRL_BC_EN              0x4000000 /* 1: upload all broadcast
> frame without error to system */ +#define
> MAC_CTRL_DBG                0x8000000 /* 1: upload all received frame
> to system (Debug Mode) */ + +/* MAC IPG/IFG Control Register  */
> +#define REG_MAC_IPG_IFG             0x1484 +#define
> MAC_IPG_IFG_IPGT_SHIFT      0     /* Desired back to back
> inter-packet gap. The default is 96-bit time */ +#define
> MAC_IPG_IFG_IPGT_MASK       0x7f +#define
> MAC_IPG_IFG_MIFG_SHIFT      8     /* Minimum number of IFG to enforce
> in between RX frames */ +#define     MAC_IPG_IFG_MIFG_MASK
> 0xff  /* Frame gap below such IFP is dropped */ +#define
> MAC_IPG_IFG_IPGR1_SHIFT     16    /* 64bit Carrier-Sense window */
> +#define     MAC_IPG_IFG_IPGR1_MASK      0x7f +#define
> MAC_IPG_IFG_IPGR2_SHIFT     24    /* 96-bit IPG window */
> +#define     MAC_IPG_IFG_IPGR2_MASK      0x7f + +/* MAC STATION
> ADDRESS  */ +#define REG_MAC_STA_ADDR            0x1488 + +/* Hash
> table for multicast address */ +#define REG_RX_HASH_TABLE
> 0x1490 + + +/* MAC Half-Duplex Control Register */ +#define
> REG_MAC_HALF_DUPLX_CTRL     0x1498 +#define
> MAC_HALF_DUPLX_CTRL_LCOL_SHIFT   0      /* Collision Window */
> +#define     MAC_HALF_DUPLX_CTRL_LCOL_MASK    0x3ff +#define
> MAC_HALF_DUPLX_CTRL_RETRY_SHIFT  12     /* Retransmission maximum,
> afterwards the packet will be discarded */ +#define
> MAC_HALF_DUPLX_CTRL_RETRY_MASK   0xf +#define
> MAC_HALF_DUPLX_CTRL_EXC_DEF_EN   0x10000 /* 1: Allow the transmission
> of a packet which has been excessively deferred */ +#define
> MAC_HALF_DUPLX_CTRL_NO_BACK_C    0x20000 /* 1: No back-off on
> collision, immediately start the retransmission */ +#define
> MAC_HALF_DUPLX_CTRL_NO_BACK_P    0x40000 /* 1: No back-off on
> backpressure, immediately start the transmission after back pressure
> */ +#define     MAC_HALF_DUPLX_CTRL_ABEBE        0x80000 /* 1:
> Alternative Binary Exponential Back-off Enabled */ +#define
> MAC_HALF_DUPLX_CTRL_ABEBT_SHIFT  20      /* Maximum binary
> exponential number */ +#define     MAC_HALF_DUPLX_CTRL_ABEBT_MASK
> 0xf +#define     MAC_HALF_DUPLX_CTRL_JAMIPG_SHIFT 24      /* IPG to
> start JAM for collision based flow control in half-duplex */
> +#define     MAC_HALF_DUPLX_CTRL_JAMIPG_MASK  0xf     /* mode. In
> unit of 8-bit time */ + +/* Maximum Frame Length Control Register
> */ +#define REG_MTU                     0x149c + +/* Wake-On-Lan
> control register */ +#define REG_WOL_CTRL                0x14a0
> +#define     WOL_PATTERN_EN                  0x00000001 +#define
> WOL_PATTERN_PME_EN              0x00000002 +#define
> WOL_MAGIC_EN                    0x00000004 +#define
> WOL_MAGIC_PME_EN                0x00000008 +#define
> WOL_LINK_CHG_EN                 0x00000010 +#define
> WOL_LINK_CHG_PME_EN             0x00000020 +#define
> WOL_PATTERN_ST                  0x00000100 +#define
> WOL_MAGIC_ST                    0x00000200 +#define
> WOL_LINKCHG_ST                  0x00000400 +#define
> WOL_CLK_SWITCH_EN               0x00008000 +#define
> WOL_PT0_EN                      0x00010000 +#define
> WOL_PT1_EN                      0x00020000 +#define
> WOL_PT2_EN                      0x00040000 +#define
> WOL_PT3_EN                      0x00080000 +#define
> WOL_PT4_EN                      0x00100000 +#define
> WOL_PT5_EN                      0x00200000 +#define
> WOL_PT6_EN                      0x00400000 +/* WOL Length ( 2 DWORD )
> */ +#define REG_WOL_PATTERN_LEN         0x14a4 +#define
> WOL_PT_LEN_MASK                 0x7f +#define
> WOL_PT0_LEN_SHIFT               0 +#define
> WOL_PT1_LEN_SHIFT               8 +#define
> WOL_PT2_LEN_SHIFT               16 +#define
> WOL_PT3_LEN_SHIFT               24 +#define
> WOL_PT4_LEN_SHIFT               0 +#define
> WOL_PT5_LEN_SHIFT               8 +#define
> WOL_PT6_LEN_SHIFT               16 + +/* Internal SRAM Partition
> Register */ +#define REG_SRAM_TRD_ADDR           0x1518 +#define
> REG_SRAM_TRD_LEN            0x151C +#define
> REG_SRAM_RXF_ADDR           0x1520 +#define
> REG_SRAM_RXF_LEN            0x1524 +#define
> REG_SRAM_TXF_ADDR           0x1528 +#define
> REG_SRAM_TXF_LEN            0x152C +#define
> REG_SRAM_TCPH_ADDR          0x1530 +#define
> REG_SRAM_PKTH_ADDR          0x1532 + +/* Load Ptr Register */
> +#define REG_LOAD_PTR                0x1534  /* Software sets this
> bit after the initialization of the head and tail */ + +/*
> + * addresses of all descriptors, as well as the following descriptor
> + * control register, which triggers each function block to load the
> head
> + * pointer to prepare for the operation. This bit is then
> self-cleared
> + * after one cycle.
> + */
> +
> +/* Descriptor Control register  */
> +#define REG_RXF3_BASE_ADDR_HI           0x153C
> +#define REG_DESC_BASE_ADDR_HI           0x1540
> +#define REG_RXF0_BASE_ADDR_HI           0x1540 /* share with DESC
> BASE ADDR HI */ +#define REG_HOST_RXF0_PAGE0_LO          0x1544
> +#define REG_HOST_RXF0_PAGE1_LO          0x1548
> +#define REG_TPD_BASE_ADDR_LO            0x154C
> +#define REG_RXF1_BASE_ADDR_HI           0x1550
> +#define REG_RXF2_BASE_ADDR_HI           0x1554
> +#define REG_HOST_RXFPAGE_SIZE           0x1558
> +#define REG_TPD_RING_SIZE               0x155C
> +/* RSS about */
> +#define REG_RSS_KEY0                    0x14B0
> +#define REG_RSS_KEY1                    0x14B4
> +#define REG_RSS_KEY2                    0x14B8
> +#define REG_RSS_KEY3                    0x14BC
> +#define REG_RSS_KEY4                    0x14C0
> +#define REG_RSS_KEY5                    0x14C4
> +#define REG_RSS_KEY6                    0x14C8
> +#define REG_RSS_KEY7                    0x14CC
> +#define REG_RSS_KEY8                    0x14D0
> +#define REG_RSS_KEY9                    0x14D4
> +#define REG_IDT_TABLE4                  0x14E0
> +#define REG_IDT_TABLE5                  0x14E4
> +#define REG_IDT_TABLE6                  0x14E8
> +#define REG_IDT_TABLE7                  0x14EC
> +#define REG_IDT_TABLE0                  0x1560
> +#define REG_IDT_TABLE1                  0x1564
> +#define REG_IDT_TABLE2                  0x1568
> +#define REG_IDT_TABLE3                  0x156C
> +#define REG_IDT_TABLE                   REG_IDT_TABLE0
> +#define REG_RSS_HASH_VALUE              0x1570
> +#define REG_RSS_HASH_FLAG               0x1574
> +#define REG_BASE_CPU_NUMBER             0x157C
> +
> +
> +/* TXQ Control Register */
> +#define REG_TXQ_CTRL                0x1580
> +#define     TXQ_CTRL_NUM_TPD_BURST_MASK     0xF
> +#define     TXQ_CTRL_NUM_TPD_BURST_SHIFT    0
> +#define     TXQ_CTRL_EN                     0x20  /* 1: Enable TXQ */
> +#define     TXQ_CTRL_ENH_MODE               0x40  /* Performance
> enhancement mode, in which up to two back-to-back DMA read commands
> might be dispatched. */ +#define     TXQ_CTRL_TXF_BURST_NUM_SHIFT
> 16    /* Number of data byte to read in a cache-aligned burst. Each
> SRAM entry is 8-byte in length. */ +#define
> TXQ_CTRL_TXF_BURST_NUM_MASK     0xffff + +/* Jumbo packet Threshold
> for task offload */ +#define REG_TX_EARLY_TH
> 0x1584 /* Jumbo frame threshold in QWORD unit. Packet greater than */
> +/* JUMBO_TASK_OFFLOAD_THRESHOLD will not be task offloaded. */
> +#define     TX_TX_EARLY_TH_MASK             0x7ff +#define
> TX_TX_EARLY_TH_SHIFT            0 + +
> +/* RXQ Control Register */
> +#define REG_RXQ_CTRL                0x15A0
> +#define         RXQ_CTRL_PBA_ALIGN_32                   0   /*
> rx-packet alignment */ +#define
> RXQ_CTRL_PBA_ALIGN_64                   1 +#define
> RXQ_CTRL_PBA_ALIGN_128                  2 +#define
> RXQ_CTRL_PBA_ALIGN_256                  3 +#define
> RXQ_CTRL_Q1_EN                         0x10 +#define
> RXQ_CTRL_Q2_EN                         0x20 +#define
> RXQ_CTRL_Q3_EN                         0x40 +#define
> RXQ_CTRL_IPV6_XSUM_VERIFY_EN           0x80 +#define
> RXQ_CTRL_HASH_TLEN_SHIFT                8 +#define
> RXQ_CTRL_HASH_TLEN_MASK                 0xFF +#define
> RXQ_CTRL_HASH_TYPE_IPV4                 0x10000 +#define
> RXQ_CTRL_HASH_TYPE_IPV4_TCP             0x20000 +#define
> RXQ_CTRL_HASH_TYPE_IPV6                 0x40000 +#define
> RXQ_CTRL_HASH_TYPE_IPV6_TCP             0x80000 +#define
> RXQ_CTRL_RSS_MODE_DISABLE               0 +#define
> RXQ_CTRL_RSS_MODE_SQSINT                0x4000000 +#define
> RXQ_CTRL_RSS_MODE_MQUESINT              0x8000000 +#define
> RXQ_CTRL_RSS_MODE_MQUEMINT              0xC000000 +#define
> RXQ_CTRL_NIP_QUEUE_SEL_TBL              0x10000000 +#define
> RXQ_CTRL_HASH_ENABLE                    0x20000000 +#define
> RXQ_CTRL_CUT_THRU_EN                    0x40000000 +#define
> RXQ_CTRL_EN                             0x80000000 +
> +/* Rx jumbo packet threshold and rrd  retirement timer  */
> +#define REG_RXQ_JMBOSZ_RRDTIM       0x15A4
> +/*
> + * Jumbo packet threshold for non-VLAN packet, in QWORD (64-bit)
> unit.
> + * When the packet length greater than or equal to this value, RXQ
> + * shall start cut-through forwarding of the received packet.
> + */
> +#define         RXQ_JMBOSZ_TH_MASK      0x7ff
> +#define         RXQ_JMBOSZ_TH_SHIFT         0  /* RRD retirement
> timer. Decrement by 1 after every 512ns passes*/ +#define
> RXQ_JMBO_LKAH_MASK          0xf +#define
> RXQ_JMBO_LKAH_SHIFT         11 +
> +/* RXF flow control register */
> +#define REG_RXQ_RXF_PAUSE_THRESH    0x15A8
> +#define     RXQ_RXF_PAUSE_TH_HI_SHIFT       0
> +#define     RXQ_RXF_PAUSE_TH_HI_MASK        0xfff
> +#define     RXQ_RXF_PAUSE_TH_LO_SHIFT       16
> +#define     RXQ_RXF_PAUSE_TH_LO_MASK        0xfff
> +
> +
> +/* DMA Engine Control Register */
> +#define REG_DMA_CTRL                0x15C0
> +#define     DMA_CTRL_DMAR_IN_ORDER          0x1
> +#define     DMA_CTRL_DMAR_ENH_ORDER         0x2
> +#define     DMA_CTRL_DMAR_OUT_ORDER         0x4
> +#define     DMA_CTRL_RCB_VALUE              0x8
> +#define     DMA_CTRL_DMAR_BURST_LEN_SHIFT   4
> +#define     DMA_CTRL_DMAR_BURST_LEN_MASK    7
> +#define     DMA_CTRL_DMAW_BURST_LEN_SHIFT   7
> +#define     DMA_CTRL_DMAW_BURST_LEN_MASK    7
> +#define     DMA_CTRL_DMAR_REQ_PRI           0x400
> +#define     DMA_CTRL_DMAR_DLY_CNT_MASK      0x1F
> +#define     DMA_CTRL_DMAR_DLY_CNT_SHIFT     11
> +#define     DMA_CTRL_DMAW_DLY_CNT_MASK      0xF
> +#define     DMA_CTRL_DMAW_DLY_CNT_SHIFT     16
> +#define     DMA_CTRL_TXCMB_EN               0x100000
> +#define     DMA_CTRL_RXCMB_EN                          0x200000
> +
> +
> +/* CMB/SMB Control Register */
> +#define REG_SMB_STAT_TIMER                      0x15C4
> +#define REG_TRIG_RRD_THRESH                     0x15CA
> +#define REG_TRIG_TPD_THRESH                     0x15C8
> +#define REG_TRIG_TXTIMER                        0x15CC
> +#define REG_TRIG_RXTIMER                        0x15CE
> +
> +/* HOST RXF Page 1,2,3 address */
> +#define REG_HOST_RXF1_PAGE0_LO                  0x15D0
> +#define REG_HOST_RXF1_PAGE1_LO                  0x15D4
> +#define REG_HOST_RXF2_PAGE0_LO                  0x15D8
> +#define REG_HOST_RXF2_PAGE1_LO                  0x15DC
> +#define REG_HOST_RXF3_PAGE0_LO                  0x15E0
> +#define REG_HOST_RXF3_PAGE1_LO                  0x15E4
> +
> +/* Mail box */
> +#define REG_MB_RXF1_RADDR                       0x15B4
> +#define REG_MB_RXF2_RADDR                       0x15B8
> +#define REG_MB_RXF3_RADDR                       0x15BC
> +#define REG_MB_TPD_PROD_IDX                     0x15F0
> +
> +/* RXF-Page 0-3  PageNo & Valid bit */
> +#define REG_HOST_RXF0_PAGE0_VLD     0x15F4
> +#define     HOST_RXF_VALID              1
> +#define     HOST_RXF_PAGENO_SHIFT       1
> +#define     HOST_RXF_PAGENO_MASK        0x7F
> +#define REG_HOST_RXF0_PAGE1_VLD     0x15F5
> +#define REG_HOST_RXF1_PAGE0_VLD     0x15F6
> +#define REG_HOST_RXF1_PAGE1_VLD     0x15F7
> +#define REG_HOST_RXF2_PAGE0_VLD     0x15F8
> +#define REG_HOST_RXF2_PAGE1_VLD     0x15F9
> +#define REG_HOST_RXF3_PAGE0_VLD     0x15FA
> +#define REG_HOST_RXF3_PAGE1_VLD     0x15FB
> +
> +/* Interrupt Status Register */
> +#define REG_ISR    0x1600
> +#define  ISR_SMB               1
> +#define  ISR_TIMER             2       /* Interrupt when Timer is
> counted down to zero */ +/*
> + * Software manual interrupt, for debug. Set when SW_MAN_INT_EN is
> set
> + * in Table 51 Selene Master Control Register (Offset 0x1400).
> + */
> +#define  ISR_MANUAL            4
> +#define  ISR_HW_RXF_OV          8        /* RXF overflow interrupt */
> +#define  ISR_HOST_RXF0_OV       0x10
> +#define  ISR_HOST_RXF1_OV       0x20
> +#define  ISR_HOST_RXF2_OV       0x40
> +#define  ISR_HOST_RXF3_OV       0x80
> +#define  ISR_TXF_UN             0x100
> +#define  ISR_RX0_PAGE_FULL      0x200
> +#define  ISR_DMAR_TO_RST        0x400
> +#define  ISR_DMAW_TO_RST        0x800
> +#define  ISR_GPHY               0x1000
> +#define  ISR_TX_CREDIT          0x2000
> +#define  ISR_GPHY_LPW           0x4000    /* GPHY low power state
> interrupt */ +#define  ISR_RX_PKT             0x10000   /* One packet
> received, triggered by RFD */ +#define  ISR_TX_PKT
> 0x20000   /* One packet transmitted, triggered by TPD */ +#define
> ISR_TX_DMA             0x40000 +#define  ISR_RX_PKT_1
> 0x80000 +#define  ISR_RX_PKT_2           0x100000
> +#define  ISR_RX_PKT_3           0x200000
> +#define  ISR_MAC_RX             0x400000
> +#define  ISR_MAC_TX             0x800000
> +#define  ISR_UR_DETECTED        0x1000000
> +#define  ISR_FERR_DETECTED      0x2000000
> +#define  ISR_NFERR_DETECTED     0x4000000
> +#define  ISR_CERR_DETECTED      0x8000000
> +#define  ISR_PHY_LINKDOWN       0x10000000
> +#define  ISR_DIS_INT            0x80000000
> +
> +
> +/* Interrupt Mask Register */
> +#define REG_IMR 0x1604
> +
> +
> +#define IMR_NORMAL_MASK (\
> +               ISR_SMB         |\
> +               ISR_TXF_UN      |\
> +               ISR_HW_RXF_OV   |\
> +               ISR_HOST_RXF0_OV|\
> +               ISR_MANUAL      |\
> +               ISR_GPHY        |\
> +               ISR_GPHY_LPW    |\
> +               ISR_DMAR_TO_RST |\
> +               ISR_DMAW_TO_RST |\
> +               ISR_PHY_LINKDOWN|\
> +               ISR_RX_PKT      |\
> +               ISR_TX_PKT)
> +
> +#define ISR_TX_EVENT (ISR_TXF_UN | ISR_TX_PKT)
> +#define ISR_RX_EVENT (ISR_HOST_RXF0_OV | ISR_HW_RXF_OV | ISR_RX_PKT)
> +
> +#define REG_MAC_RX_STATUS_BIN 0x1700
> +#define REG_MAC_RX_STATUS_END 0x175c
> +#define REG_MAC_TX_STATUS_BIN 0x1760
> +#define REG_MAC_TX_STATUS_END 0x17c0
> +
> +/* Hardware Offset Register */
> +#define REG_HOST_RXF0_PAGEOFF 0x1800
> +#define REG_TPD_CONS_IDX      0x1804
> +#define REG_HOST_RXF1_PAGEOFF 0x1808
> +#define REG_HOST_RXF2_PAGEOFF 0x180C
> +#define REG_HOST_RXF3_PAGEOFF 0x1810
> +
> +/* RXF-Page 0-3 Offset DMA Address */
> +#define REG_HOST_RXF0_MB0_LO  0x1820
> +#define REG_HOST_RXF0_MB1_LO  0x1824
> +#define REG_HOST_RXF1_MB0_LO  0x1828
> +#define REG_HOST_RXF1_MB1_LO  0x182C
> +#define REG_HOST_RXF2_MB0_LO  0x1830
> +#define REG_HOST_RXF2_MB1_LO  0x1834
> +#define REG_HOST_RXF3_MB0_LO  0x1838
> +#define REG_HOST_RXF3_MB1_LO  0x183C
> +
> +/* Tpd CMB DMA Address */
> +#define REG_HOST_TX_CMB_LO    0x1840
> +#define REG_HOST_SMB_ADDR_LO  0x1844
> +
> +/* DEBUG ADDR */
> +#define REG_DEBUG_DATA0 0x1900
> +#define REG_DEBUG_DATA1 0x1904
> +
> +/***************************** MII definition
> ***************************************/ +/* PHY Common Register */
> +#define MII_BMCR                        0x00
> +#define MII_BMSR                        0x01
> +#define MII_PHYSID1                     0x02
> +#define MII_PHYSID2                     0x03
> +#define MII_ADVERTISE                   0x04
> +#define MII_LPA                         0x05
> +#define MII_EXPANSION                   0x06
> +#define MII_AT001_CR                    0x09
> +#define MII_AT001_SR                    0x0A
> +#define MII_AT001_ESR                   0x0F
> +#define MII_AT001_PSCR                  0x10
> +#define MII_AT001_PSSR                  0x11
> +#define MII_INT_CTRL                    0x12
> +#define MII_INT_STATUS                  0x13
> +#define MII_SMARTSPEED                  0x14
> +#define MII_RERRCOUNTER                 0x15
> +#define MII_SREVISION                   0x16
> +#define MII_RESV1                       0x17
> +#define MII_LBRERROR                    0x18
> +#define MII_PHYADDR                     0x19
> +#define MII_RESV2                       0x1a
> +#define MII_TPISTATUS                   0x1b
> +#define MII_NCONFIG                     0x1c
> +
> +#define MII_DBG_ADDR                   0x1D
> +#define MII_DBG_DATA                   0x1E
> +
> +
> +/* PHY Control Register */
> +#define MII_CR_SPEED_SELECT_MSB                  0x0040  /* bits
> 6,13: 10=1000, 01=100, 00=10 */ +#define
> MII_CR_COLL_TEST_ENABLE                  0x0080  /* Collision test
> enable */ +#define MII_CR_FULL_DUPLEX
> 0x0100  /* FDX =1, half duplex =0 */ +#define
> MII_CR_RESTART_AUTO_NEG                  0x0200  /* Restart auto
> negotiation */ +#define MII_CR_ISOLATE
> 0x0400  /* Isolate PHY from MII */ +#define
> MII_CR_POWER_DOWN                        0x0800  /* Power down */
> +#define MII_CR_AUTO_NEG_EN                       0x1000  /* Auto Neg
> Enable */ +#define MII_CR_SPEED_SELECT_LSB
> 0x2000  /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define
> MII_CR_LOOPBACK                          0x4000  /* 0 = normal, 1 =
> loopback */ +#define MII_CR_RESET
> 0x8000  /* 0 = normal, 1 = PHY reset */ +#define
> MII_CR_SPEED_MASK                        0x2040 +#define
> MII_CR_SPEED_1000                        0x0040 +#define
> MII_CR_SPEED_100                         0x2000 +#define
> MII_CR_SPEED_10                          0x0000 + + +/* PHY Status
> Register */ +#define MII_SR_EXTENDED_CAPS
> 0x0001  /* Extended register capabilities */ +#define
> MII_SR_JABBER_DETECT                     0x0002  /* Jabber Detected
> */ +#define MII_SR_LINK_STATUS                       0x0004  /* Link
> Status 1 = link */ +#define MII_SR_AUTONEG_CAPS
> 0x0008  /* Auto Neg Capable */ +#define
> MII_SR_REMOTE_FAULT                      0x0010  /* Remote Fault
> Detect */ +#define MII_SR_AUTONEG_COMPLETE
> 0x0020  /* Auto Neg Complete */ +#define
> MII_SR_PREAMBLE_SUPPRESS                 0x0040  /* Preamble may be
> suppressed */ +#define MII_SR_EXTENDED_STATUS
> 0x0100  /* Ext. status info in Reg 0x0F */ +#define
> MII_SR_100T2_HD_CAPS                     0x0200  /* 100T2 Half Duplex
> Capable */ +#define MII_SR_100T2_FD_CAPS
> 0x0400  /* 100T2 Full Duplex Capable */ +#define
> MII_SR_10T_HD_CAPS                       0x0800  /* 10T   Half Duplex
> Capable */ +#define MII_SR_10T_FD_CAPS
> 0x1000  /* 10T   Full Duplex Capable */ +#define
> MII_SR_100X_HD_CAPS                      0x2000  /* 100X  Half Duplex
> Capable */ +#define MII_SR_100X_FD_CAPS
> 0x4000  /* 100X  Full Duplex Capable */ +#define
> MII_SR_100T4_CAPS                        0x8000  /* 100T4 Capable */
> + +/* Link partner ability register. */ +#define
> MII_LPA_SLCT                             0x001f  /* Same as advertise
> selector  */ +#define MII_LPA_10HALF
> 0x0020  /* Can do 10mbps half-duplex   */ +#define
> MII_LPA_10FULL                           0x0040  /* Can do 10mbps
> full-duplex   */ +#define MII_LPA_100HALF
> 0x0080  /* Can do 100mbps half-duplex  */ +#define
> MII_LPA_100FULL                          0x0100  /* Can do 100mbps
> full-duplex  */ +#define MII_LPA_100BASE4
> 0x0200  /* 100BASE-T4  */ +#define
> MII_LPA_PAUSE                            0x0400  /* PAUSE */ +#define
> MII_LPA_ASYPAUSE                         0x0800  /* Asymmetrical
> PAUSE */ +#define MII_LPA_RFAULT                           0x2000  /*
> Link partner faulted        */ +#define
> MII_LPA_LPACK                            0x4000  /* Link partner
> acked us       */ +#define MII_LPA_NPAGE
> 0x8000  /* Next page bit               */ + +/* Autoneg Advertisement
> Register */ +#define MII_AR_SELECTOR_FIELD
> 0x0001  /* indicates IEEE 802.3 CSMA/CD */ +#define
> MII_AR_10T_HD_CAPS                      0x0020  /* 10T   Half Duplex
> Capable */ +#define MII_AR_10T_FD_CAPS
> 0x0040  /* 10T   Full Duplex Capable */ +#define
> MII_AR_100TX_HD_CAPS                    0x0080  /* 100TX Half Duplex
> Capable */ +#define MII_AR_100TX_FD_CAPS
> 0x0100  /* 100TX Full Duplex Capable */ +#define
> MII_AR_100T4_CAPS                       0x0200  /* 100T4 Capable */
> +#define MII_AR_PAUSE                            0x0400  /* Pause
> operation desired */ +#define MII_AR_ASM_DIR
> 0x0800  /* Asymmetric Pause Direction bit */ +#define
> MII_AR_REMOTE_FAULT                     0x2000  /* Remote Fault
> detected */ +#define MII_AR_NEXT_PAGE
> 0x8000  /* Next Page ability supported */ +#define
> MII_AR_SPEED_MASK                       0x01E0 +#define
> MII_AR_DEFAULT_CAP_MASK                 0x0DE0 + +/* 1000BASE-T
> Control Register */ +#define MII_AT001_CR_1000T_HD_CAPS
> 0x0100  /* Advertise 1000T HD capability */ +#define
> MII_AT001_CR_1000T_FD_CAPS              0x0200  /* Advertise 1000T FD
> capability  */ +#define MII_AT001_CR_1000T_REPEATER_DTE
> 0x0400  /* 1=Repeater/switch device port */ +/* 0=DTE device */
> +#define MII_AT001_CR_1000T_MS_VALUE             0x0800  /*
> 1=Configure PHY as Master */ +/* 0=Configure PHY as Slave */ +#define
> MII_AT001_CR_1000T_MS_ENABLE            0x1000  /* 1=Master/Slave
> manual config value */ +/* 0=Automatic Master/Slave config */
> +#define MII_AT001_CR_1000T_TEST_MODE_NORMAL     0x0000  /* Normal
> Operation */ +#define MII_AT001_CR_1000T_TEST_MODE_1
> 0x2000  /* Transmit Waveform test */ +#define
> MII_AT001_CR_1000T_TEST_MODE_2          0x4000  /* Master Transmit
> Jitter test */ +#define MII_AT001_CR_1000T_TEST_MODE_3
> 0x6000  /* Slave Transmit Jitter test */ +#define
> MII_AT001_CR_1000T_TEST_MODE_4          0x8000  /* Transmitter
> Distortion test */ +#define MII_AT001_CR_1000T_SPEED_MASK
> 0x0300 +#define MII_AT001_CR_1000T_DEFAULT_CAP_MASK     0x0300 + +/*
> 1000BASE-T Status Register */ +#define
> MII_AT001_SR_1000T_LP_HD_CAPS           0x0400  /* LP is 1000T HD
> capable */ +#define MII_AT001_SR_1000T_LP_FD_CAPS
> 0x0800  /* LP is 1000T FD capable */ +#define
> MII_AT001_SR_1000T_REMOTE_RX_STATUS     0x1000  /* Remote receiver OK
> */ +#define MII_AT001_SR_1000T_LOCAL_RX_STATUS      0x2000  /* Local
> receiver OK */ +#define MII_AT001_SR_1000T_MS_CONFIG_RES
> 0x4000  /* 1=Local TX is Master, 0=Slave */ +#define
> MII_AT001_SR_1000T_MS_CONFIG_FAULT      0x8000  /* Master/Slave
> config fault */ +#define MII_AT001_SR_1000T_REMOTE_RX_STATUS_SHIFT
> 12 +#define MII_AT001_SR_1000T_LOCAL_RX_STATUS_SHIFT    13 + +/*
> Extended Status Register */ +#define
> MII_AT001_ESR_1000T_HD_CAPS             0x1000  /* 1000T HD capable
> */ +#define MII_AT001_ESR_1000T_FD_CAPS             0x2000  /* 1000T
> FD capable */ +#define MII_AT001_ESR_1000X_HD_CAPS
> 0x4000  /* 1000X HD capable */ +#define
> MII_AT001_ESR_1000X_FD_CAPS             0x8000  /* 1000X FD capable
> */ + +/* AT001 PHY Specific Control Register */ +#define
> MII_AT001_PSCR_JABBER_DISABLE           0x0001  /* 1=Jabber Function
> disabled */ +#define MII_AT001_PSCR_POLARITY_REVERSAL
> 0x0002  /* 1=Polarity Reversal enabled */ +#define
> MII_AT001_PSCR_SQE_TEST                 0x0004  /* 1=SQE Test enabled
> *// +#define MII_AT001_PSCR_MAC_POWERDOWN            0x0008 +#define
> MII_AT001_PSCR_CLK125_DISABLE           0x0010  /* 1=CLK125 low,
> +                                                        * 0=CLK125
> toggling
> +                                                        */
> +#define MII_AT001_PSCR_MDI_MANUAL_MODE          0x0000  /* MDI
> Crossover Mode bits 6:5 */ +/* Manual MDI configuration */
> +#define MII_AT001_PSCR_MDIX_MANUAL_MODE         0x0020  /* Manual
> MDIX configuration */ +#define
> MII_AT001_PSCR_AUTO_X_1000T             0x0040  /* 1000BASE-T: Auto
> crossover,
> +                                                        *
> 100BASE-TX/10BASE-T:
> +                                                        *  MDI Mode
> +                                                        */
> +#define MII_AT001_PSCR_AUTO_X_MODE              0x0060  /* Auto
> crossover enabled
> +                                                        * all speeds.
> +                                                        */
> +#define MII_AT001_PSCR_10BT_EXT_DIST_ENABLE     0x0080
> +/* 1=Enable Extended 10BASE-T distance
> + * (Lower 10BASE-T RX Threshold)
> + * 0=Normal 10BASE-T RX Threshold */
> +#define MII_AT001_PSCR_MII_5BIT_ENABLE          0x0100
> +/* 1=5-Bit interface in 100BASE-TX
> + * 0=MII interface in 100BASE-TX */
> +#define MII_AT001_PSCR_SCRAMBLER_DISABLE        0x0200  /*
> 1=Scrambler disable */ +#define
> MII_AT001_PSCR_FORCE_LINK_GOOD          0x0400  /* 1=Force link good
> */ +#define MII_AT001_PSCR_ASSERT_CRS_ON_TX         0x0800  /*
> 1=Assert CRS on Transmit */ +#define
> MII_AT001_PSCR_POLARITY_REVERSAL_SHIFT    1 +#define
> MII_AT001_PSCR_AUTO_X_MODE_SHIFT          5 +#define
> MII_AT001_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7 + +
> +/* AT001 PHY Specific Status Register */
> +#define MII_AT001_PSSR_SPD_DPLX_RESOLVED        0x0800  /* 1=Speed &
> Duplex resolved */ +#define MII_AT001_PSSR_DPLX
> 0x2000  /* 1=Duplex 0=Half Duplex */ +#define
> MII_AT001_PSSR_SPEED                    0xC000  /* Speed, bits 14:15
> */ +#define MII_AT001_PSSR_10MBS                    0x0000  /*
> 00=10Mbs */ +#define MII_AT001_PSSR_100MBS
> 0x4000  /* 01=100Mbs */ +#define
> MII_AT001_PSSR_1000MBS                  0x8000  /* 10=1000Mbs */ +
> +/*********************PCI Command Register
> ******************************/ +/* PCI Command Register Bit
> Definitions */ +#define PCI_REG_COMMAND         0x04    /* PCI
> Command Register */ +#define CMD_IO_SPACE            0x0001 +#define
> CMD_MEMORY_SPACE        0x0002 +#define CMD_BUS_MASTER          0x0004
> +
> +/* Wake Up Filter Control */
> +#define AT_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable
> */ +#define AT_WUFC_MAG  0x00000002 /* Magic Packet Wakeup Enable */
> +#define AT_WUFC_EX   0x00000004 /* Directed Exact Wakeup Enable */
> +#define AT_WUFC_MC   0x00000008 /* Multicast Wakeup Enable */
> +#define AT_WUFC_BC   0x00000010 /* Broadcast Wakeup Enable */
> +
> +/*********************************************************************/
> +
> +/* Error Codes */
> +
> +#define AT_SUCCESS         0
> +#define AT_ERR_EEPROM      1
> +#define AT_ERR_PHY         2
> +#define AT_ERR_CONFIG      3
> +#define AT_ERR_PARAM       4
> +#define AT_ERR_MAC_TYPE    5
> +#define AT_ERR_PHY_TYPE    6
> +#define AT_ERR_PHY_SPEED   7
> +#define AT_ERR_PHY_RES     8
> +#define AT_ERR_TIMEOUT     9
> +
> +#define SPEED_0            0xffff
> +#define SPEED_10           10
> +#define SPEED_100          100
> +#define SPEED_1000         1000
> +#define HALF_DUPLEX        1
> +#define FULL_DUPLEX        2
> +
> +#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but
> 1000-Half */ +#define AUTONEG_ADVERTISE_10_100_ALL    0x000F /* All
> 10/100 speeds*/ +#define AUTONEG_ADVERTISE_10_ALL        0x0003 /*
> 10Mbps Full & Half speeds*/ +
> +
> +/* The size (in bytes) of a ethernet packet */
> +#define ENET_HEADER_SIZE                14
> +#define MAXIMUM_ETHERNET_FRAME_SIZE     1518 /* with FCS */
> +#define MINIMUM_ETHERNET_FRAME_SIZE     64   /* with FCS */
> +#define ETHERNET_FCS_SIZE               4
> +#define MAX_JUMBO_FRAME_SIZE            0x2000
> +#define VLAN_SIZE                                               4
> +
> +#define PHY_AUTO_NEG_TIME               45          /* 4.5 Seconds */
> +#define PHY_FORCE_TIME                  20          /* 2.0 Seconds */
> +
> +/* For checksumming , the sum of all words in the EEPROM should
> equal 0xBABA */ +#define EEPROM_SUM                      0xBABA
> +#define NODE_ADDRESS_SIZE               6
> +
> +
> +/* TPD definition */
> +struct atl1e_tpd_desc {
> +       u64         addr;
> +       u16         buf_len :14;
> +       u16         dma_int :1;
> +       u16         tx_int  :1;
> +       u16         vlan;
> +       u16         eop     :1;
> +       u16         ipver   :1;     /* 0 : IPV4, 1:IPV6 */
> +       u16         ins_vlan:1;
> +       u16         my_xsum :1;
> +       u16         segment :1;
> +       u16         ipxsum  :1;
> +       u16         tcpxsum :1;
> +       u16         udpxsum :1;
> +       u16         vlan_tag:1;
> +       u16         eth_type:1;
> +       u16         iphdrlen:4;
> +       u16         tcphdrlen:4;
> +       u16         hdr_flag:1;
> +       u16         tcp_mss :13;
> +} __attribute__((packed));

Please don't use bitfields.  Convert these to shift/mask pairs.

> +
> +struct atl1e_tpd_ipv6_desc {
> +       u64         addr;
> +       u16         buf_len :14;
> +       u16         dma_int :1;
> +       u16         tx_int  :1;
> +       u16         vlan;
> +       u16         eop     :1;
> +       u16         ipver   :1;     /* 0 : IPV4, 1:IPV6 */
> +       u16         ins_vlan:1;
> +       u16         my_xsum :1;
> +       u16         segment :1;
> +       u16         ipv6hdrlen_1:3;
> +       u16         vlan_tag:1;
> +       u16         eth_type:1;
> +       u16         ipv6hdrlen_2:4;
> +       u16         tcphdrlen:4;
> +       u16         hdr_flag:1;
> +       u16         tcp_mss :13;
> +} __attribute__((packed));

Ditto.

> +
> +/* Tpd for custom checksum  */
> +struct atl1e_tpd_csum_desc {
> +       u64        addr;
> +       u16        buf_len :14;
> +       u16        dma_int :1;
> +       u16        tx_int  :1;
> +       u16        vlan;
> +       u16        eop     :1;
> +       u16        coals   :1;
> +       u16        ins_vlan:1;
> +       u16        my_xsum :1;
> +       u16        segment :1;
> +       u16        ipxsum  :1;
> +       u16        tcpxsum :1;
> +       u16        udpxsum :1;
> +       u16        vlan_tag:1;
> +       u16        eth_type:1;
> +       u16        iphdrlen:4;
> +       u16        tcphdrlen:2;
> +       u16        payld_ofs:8;
> +       u16        psdxsum_ofs:8;
> +} __attribute__((packed));

Ditto.

> +/* how about 0x2000 */
> +#define MAX_TX_BUF_LEN      0x2000
> +#define MAX_TX_BUF_SHIFT    13
> +/*#define MAX_TX_BUF_LEN  0x3000 */
> +
> +/* RRS(Receive Return Status) definition */
> +struct atl1e_recv_ret_status {
> +       u16        seq_num         ;
> +       u16        hash_lo         ;
> +       u16        ippld_xsum      ; /* ip payload checksum */
> +       u16        pkt_len :14     ;
> +       u16        cpu_n   :2      ;
> +       /* packet flags */
> +       u16        rss_ipv4:1      ;
> +       u16        rss_ipv4_tcp:1  ;
> +       u16        rss_ipv6:1      ;
> +       u16        rss_ipv6_tcp:1  ;
> +       u16        ipv6 :1         ;
> +       u16        ipv4_mf:1       ;
> +       u16        ipv4_df:1       ;
> +
> +       u16        eth_type:1      ;
> +       u16        vlan    :1      ;
> +       u16        err     :1      ;
> +       u16        ipv4    :1      ;
> +       u16        udp     :1      ;
> +       u16        tcp     :1      ;
> +       u16        bcast   :1      ;
> +       u16        mcast   :1      ;
> +       u16        pause   :1      ;
> +       /* error info */
> +       u16        crc     :1      ;
> +       u16        code    :1      ;
> +       u16        dribble :1      ;
> +       u16        runt    :1      ;
> +       u16        ov      :1      ;
> +       u16        trunc   :1      ;
> +       u16        ip_xsum :1      ;
> +       u16        l4_xsum :1      ;
> +       u16        length  :1      ;
> +       u16        dest    :1      ;
> +       u16        res2    :6      ;
> +
> +       u16        hash_hi ;
> +       u16        vtag    ; /* vlan tag if bit vlan == 1 */
> +} __attribute__((packed));

Ditto.

> +
> +typedef enum {

Please, no typedefs.

> +       atl1e_10_half = 0,
> +       atl1e_10_full = 1,
> +       atl1e_100_half = 2,
> +       atl1e_100_full = 3
> +} atl1e_speed_duplex_type;
> +
> +
> +
> +typedef enum  {
> +       atl1e_dma_req_128 = 0,
> +       atl1e_dma_req_256 = 1,
> +       atl1e_dma_req_512 = 2,
> +       atl1e_dma_req_1024 = 3,
> +       atl1e_dma_req_2048 = 4,
> +       atl1e_dma_req_4096 = 5
> +} atl1e_dma_req_block;
> +
> +typedef enum {
> +       atl1e_rrs_disable = 0,
> +       atl1e_rrs_ipv4 = 1,
> +       atl1e_rrs_ipv4_tcp = 2,
> +       atl1e_rrs_ipv6 = 4,
> +       atl1e_rrs_ipv6_tcp = 8
> +} atl1e_rrs_type;
> +
> +typedef enum {
> +       athr_l1e = 0,
> +       athr_l2e_revA = 1,
> +       athr_l2e_revB = 2
> +} atl1e_nic_type;
> +
> +struct atl1e_hw_stats {
> +       /* rx */
> +       unsigned long rx_ok;      /* The number of good packet
> received. */
> +       unsigned long rx_bcast;       /* The number of good broadcast
> packet received. */
> +       unsigned long rx_mcast;       /* The number of good multicast
> packet received. */
> +       unsigned long rx_pause;       /* The number of Pause packet
> received. */
> +       unsigned long rx_ctrl;        /* The number of Control packet
> received other than Pause frame. */
> +       unsigned long rx_fcs_err;     /* The number of packets with
> bad FCS. */
> +       unsigned long rx_len_err;     /* The number of packets with
> mismatch of length field and actual size. */
> +       unsigned long rx_byte_cnt;    /* The number of bytes of good
> packet received. FCS is NOT included. */
> +       unsigned long rx_runt;        /* The number of packets
> received that are less than 64 byte long and with good FCS. */
> +       unsigned long rx_frag;        /* The number of packets
> received that are less than 64 byte long and with bad FCS. */
> +       unsigned long rx_sz_64;       /* The number of good and bad
> packets received that are 64 byte long. */
> +       unsigned long rx_sz_65_127;   /* The number of good and bad
> packets received that are between 65 and 127-byte long. */
> +       unsigned long rx_sz_128_255;  /* The number of good and bad
> packets received that are between 128 and 255-byte long. */
> +       unsigned long rx_sz_256_511;  /* The number of good and bad
> packets received that are between 256 and 511-byte long. */
> +       unsigned long rx_sz_512_1023; /* The number of good and bad
> packets received that are between 512 and 1023-byte long. */
> +       unsigned long rx_sz_1024_1518;    /* The number of good and
> bad packets received that are between 1024 and 1518-byte long. */
> +       unsigned long rx_sz_1519_max; /* The number of good and bad
> packets received that are between 1519-byte and MTU. */
> +       unsigned long rx_sz_ov;       /* The number of good and bad
> packets received that are more than MTU size truncated by Selene. */
> +       unsigned long rx_rxf_ov;      /* The number of frame dropped
> due to occurrence of RX FIFO overflow. */
> +       unsigned long rx_rrd_ov;      /* The number of frame dropped
> due to occurrence of RRD overflow. */
> +       unsigned long rx_align_err;   /* Alignment Error */
> +       unsigned long rx_bcast_byte_cnt;  /* The byte count of
> broadcast packet received, excluding FCS. */
> +       unsigned long rx_mcast_byte_cnt;  /* The byte count of
> multicast packet received, excluding FCS. */
> +       unsigned long rx_err_addr;    /* The number of packets
> dropped due to address filtering. */ +
> +       /* tx */
> +       unsigned long tx_ok;      /* The number of good packet
> transmitted. */
> +       unsigned long tx_bcast;       /* The number of good broadcast
> packet transmitted. */
> +       unsigned long tx_mcast;       /* The number of good multicast
> packet transmitted. */
> +       unsigned long tx_pause;       /* The number of Pause packet
> transmitted. */
> +       unsigned long tx_exc_defer;   /* The number of packets
> transmitted with excessive deferral. */
> +       unsigned long tx_ctrl;        /* The number of packets
> transmitted is a control frame, excluding Pause frame. */
> +       unsigned long tx_defer;       /* The number of packets
> transmitted that is deferred. */
> +       unsigned long tx_byte_cnt;    /* The number of bytes of data
> transmitted. FCS is NOT included. */
> +       unsigned long tx_sz_64;       /* The number of good and bad
> packets transmitted that are 64 byte long. */
> +       unsigned long tx_sz_65_127;   /* The number of good and bad
> packets transmitted that are between 65 and 127-byte long. */
> +       unsigned long tx_sz_128_255;  /* The number of good and bad
> packets transmitted that are between 128 and 255-byte long. */
> +       unsigned long tx_sz_256_511;  /* The number of good and bad
> packets transmitted that are between 256 and 511-byte long. */
> +       unsigned long tx_sz_512_1023; /* The number of good and bad
> packets transmitted that are between 512 and 1023-byte long. */
> +       unsigned long tx_sz_1024_1518;    /* The number of good and
> bad packets transmitted that are between 1024 and 1518-byte long. */
> +       unsigned long tx_sz_1519_max; /* The number of good and bad
> packets transmitted that are between 1519-byte and MTU. */
> +       unsigned long tx_1_col;       /* The number of packets
> subsequently transmitted successfully with a single prior collision.
> */
> +       unsigned long tx_2_col;       /* The number of packets
> subsequently transmitted successfully with multiple prior collisions.
> */
> +       unsigned long tx_late_col;    /* The number of packets
> transmitted with late collisions. */
> +       unsigned long tx_abort_col;   /* The number of transmit
> packets aborted due to excessive collisions. */
> +       unsigned long tx_underrun;    /* The number of transmit
> packets aborted due to transmit FIFO underrun, or TRD FIFO underrun */
> +       unsigned long tx_rd_eop;      /* The number of times that
> read beyond the EOP into the next frame area when TRD was not written
> timely */
> +       unsigned long tx_len_err;     /* The number of transmit
> packets with length field does NOT match the actual frame size. */
> +       unsigned long tx_trunc;       /* The number of transmit
> packets truncated due to size exceeding MTU. */
> +       unsigned long tx_bcast_byte;  /* The byte count of broadcast
> packet transmitted, excluding FCS. */
> +       unsigned long tx_mcast_byte;  /* The byte count of multicast
> packet transmitted, excluding FCS. */ +};
> +
> +struct atl1e_hw {
> +       u8 __iomem      *hw_addr;            /* inner register
> address */
> +       resource_size_t mem_rang;
> +       void            *adapter;
> +
> +       atl1e_nic_type  nic_type;
> +       u16 device_id;
> +       u16 vendor_id;
> +       u16 subsystem_id;
> +       u16 subsystem_vendor_id;
> +       u8  revision_id;
> +       u16 pci_cmd_word;
> +       u8 mac_addr[NODE_ADDRESS_SIZE];
> +       u8 perm_mac_addr[NODE_ADDRESS_SIZE];
> +       u8  preamble_len;
> +       u16 max_frame_size;
> +       u16 rx_jumbo_th;
> +       u16 tx_jumbo_th;
> +
> +       u16 media_type;
> +#define MEDIA_TYPE_AUTO_SENSOR  0
> +#define MEDIA_TYPE_100M_FULL    1
> +#define MEDIA_TYPE_100M_HALF    2
> +#define MEDIA_TYPE_10M_FULL     3
> +#define MEDIA_TYPE_10M_HALF     4
> +
> +       u16 autoneg_advertised;
> +#define ADVERTISE_10_HALF               0x0001
> +#define ADVERTISE_10_FULL               0x0002
> +#define ADVERTISE_100_HALF              0x0004
> +#define ADVERTISE_100_FULL              0x0008
> +#define ADVERTISE_1000_HALF             0x0010 /* Not used, just FYI
> */ +#define ADVERTISE_1000_FULL             0x0020
> +       u16 mii_autoneg_adv_reg;
> +       u16 mii_1000t_ctrl_reg;
> +
> +       u16 imt;        /* Interrupt Moderator timer ( 2us
> resolution) */
> +       u16 ict;        /* Interrupt Clear timer (2us resolution) */
> +       u32 smb_timer;
> +       u16 rrd_thresh; /* Threshold of number of RRD produced to
> trigger
> +                         interrupt request */
> +       u16 tpd_thresh;
> +       u16 rx_count_down; /* 2us resolution */
> +       u16 tx_count_down;
> +
> +       u8 tpd_burst;   /* Number of TPD to prefetch in cache-aligned
> burst. */
> +       atl1e_rrs_type rrs_type;
> +       u32 base_cpu;
> +       u32 indirect_tab;
> +
> +       atl1e_dma_req_block dmar_block;
> +       atl1e_dma_req_block dmaw_block;
> +       u8 dmaw_dly_cnt;
> +       u8 dmar_dly_cnt;
> +
> +       bool phy_configured;
> +       bool re_autoneg;
> +       bool emi_ca;
> +};
> +
> +#endif /*_ATHEROS_HW_H__*/
> --
> To unsubscribe from this list: send the line "unsubscribe
> linux-kernel" in the body of a message to majordomo@...r.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists