[ 0.000000] Linux version 2.6.30-debug-03392-g44b7532 (odie@apu.appl.cs.aau.dk) (gcc version 4.3.3 (GCC) ) #17 PREEMPT Sun Jun 14 13:05:26 CEST 2009 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000002fff0000 (usable) [ 0.000000] BIOS-e820: 000000002fff0000 - 000000002fffffc0 (ACPI data) [ 0.000000] BIOS-e820: 000000002fffffc0 - 0000000030000000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] DMI 2.3 present. [ 0.000000] last_pfn = 0x2fff0 max_arch_pfn = 0x100000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-CFFFF write-protect [ 0.000000] D0000-DFFFF uncachable [ 0.000000] E0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask FE0000000 write-back [ 0.000000] 1 base 020000000 mask FF0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] initial memory mapped : 0 - 01000000 [ 0.000000] init_memory_mapping: 0000000000000000-000000002fff0000 [ 0.000000] 0000000000 - 0000400000 page 4k [ 0.000000] 0000400000 - 002fc00000 page 2M [ 0.000000] 002fc00000 - 002fff0000 page 4k [ 0.000000] kernel direct mapping tables up to 2fff0000 @ 7000-c000 [ 0.000000] ACPI: RSDP 000e6010 00014 (v00 OID_00) [ 0.000000] ACPI: RSDT 2fffa7f0 00034 (v01 INSYDE RSDT_000 00000001 _CSI 00010101) [ 0.000000] ACPI: FACP 2ffffb00 00074 (v01 COMPAL DCL56 00000200 _CSI 00010101) [ 0.000000] ACPI: DSDT 2fffac70 04E8A (v01 COMPAL DCL561 00000006 MSFT 0100000E) [ 0.000000] ACPI: FACS 2fffffc0 00040 [ 0.000000] ACPI: BOOT 2ffffb90 00028 (v01 INSYDE SYS_BOOT 00000100 _CSI 00010101) [ 0.000000] ACPI: DBGP 2ffffbc0 00034 (v01 INSYDE DBGP_000 00000100 _CSI 00010101) [ 0.000000] ACPI: SSDT 2fffa830 0029A (v01 INSYDE GV3Ref 00002000 INTL 20021002) [ 0.000000] 767MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 2fff0000 [ 0.000000] low ram: 0 - 2fff0000 [ 0.000000] node 0 low ram: 00000000 - 2fff0000 [ 0.000000] node 0 bootmap 00001000 - 00007000 [ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 002fff0000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000100000 - 0000b6f8d0] TEXT DATA BSS ==> [0000100000 - 0000b6f8d0] [ 0.000000] #2 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] [ 0.000000] #3 [0000b70000 - 0000b74120] BRK ==> [0000b70000 - 0000b74120] [ 0.000000] #4 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000] [ 0.000000] #5 [0000001000 - 0000007000] BOOTMAP ==> [0000001000 - 0000007000] [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x0002fff0 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x0002fff0 [ 0.000000] On node 0 totalpages: 196495 [ 0.000000] free_area_init_node: node 0, pgdat c05becf8, node_mem_map c1000000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3967 pages, LIFO batch:0 [ 0.000000] Normal zone: 1504 pages used for memmap [ 0.000000] Normal zone: 190992 pages, LIFO batch:31 [ 0.000000] Using APIC driver default [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic" [ 0.000000] APIC: disable apic facility [ 0.000000] nr_irqs_gsi: 16 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 30000000 (gap: 30000000:cfb80000) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194959 [ 0.000000] Kernel command line: resume=/dev/hda5 root=/dev/hda6 nofb vga=0x0f00 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] Memory: 768144k/786368k available (2333k kernel code, 17704k reserved, 2568k data, 268k init, 0k highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xfffa9000 - 0xfffff000 ( 344 kB) [ 0.000000] vmalloc : 0xf07f0000 - 0xfffa7000 ( 247 MB) [ 0.000000] lowmem : 0xc0000000 - 0xefff0000 ( 767 MB) [ 0.000000] .init : 0xc05cc000 - 0xc060f000 ( 268 kB) [ 0.000000] .data : 0xc03476d3 - 0xc05c9a98 (2568 kB) [ 0.000000] .text : 0xc0100000 - 0xc03476d3 (2333 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] NR_IRQS:288 [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 1495.248 MHz processor. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.004000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.004000] ... MAX_LOCK_DEPTH: 48 [ 0.004000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.004000] ... CLASSHASH_SIZE: 4096 [ 0.004000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.004000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.004000] ... CHAINHASH_SIZE: 16384 [ 0.004000] memory used by lock dependency info: 3743 kB [ 0.004000] per task-struct memory footprint: 1920 bytes [ 0.004037] Calibrating delay loop (skipped), value calculated using timer frequency.. 2990.49 BogoMIPS (lpj=5980992) [ 0.004357] Mount-cache hash table entries: 512 [ 0.006116] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.006222] CPU: L2 cache: 1024K [ 0.006293] mce: CPU supports 5 MCE banks [ 0.006370] ------------[ cut here ]------------ [ 0.006450] WARNING: at arch/x86/kernel/apic/apic.c:249 native_apic_write_dummy+0x32/0x3e() [ 0.006558] Hardware name: [ 0.006625] Modules linked in: [ 0.006729] Pid: 0, comm: swapper Not tainted 2.6.30-debug-03392-g44b7532 #17 [ 0.006804] Call Trace: [ 0.006880] [] warn_slowpath_common+0x65/0x95 [ 0.006956] [] warn_slowpath_null+0x12/0x15 [ 0.007031] [] native_apic_write_dummy+0x32/0x3e [ 0.007109] [] intel_init_thermal+0xd3/0x178 [ 0.007185] [] ? native_read_msr_safe+0x9/0x16 [ 0.007263] [] ? __kmalloc+0x117/0x123 [ 0.007338] [] mce_intel_feature_init+0x10/0x50 [ 0.007416] [] mcheck_init+0x1d5/0x263 [ 0.007492] [] identify_cpu+0x369/0x378 [ 0.007569] [] ? _spin_unlock+0x3d/0x49 [ 0.007644] [] ? proc_register+0x150/0x161 [ 0.007721] [] identify_boot_cpu+0xd/0x23 [ 0.007796] [] check_bugs+0xb/0xf1 [ 0.007872] [] start_kernel+0x293/0x2a7 [ 0.008011] [] i386_start_kernel+0x65/0x6a [ 0.008169] ---[ end trace 4eaa2a86a8e2da22 ]--- [ 0.008242] CPU0: Thermal monitoring enabled (TM1) [ 0.008322] Performance Counters: no PMU driver, software counters only. [ 0.008431] CPU: Intel(R) Pentium(R) M processor 1500MHz stepping 05 [ 0.008580] Checking 'hlt' instruction... OK. [ 0.025448] ACPI: Core revision 20090320 [ 0.038840] ACPI: setting ELCR to 0200 (from 0c00) [ 0.040015] ftrace: converting mcount calls to 0f 1f 44 00 00 [ 0.040093] ftrace: allocating 12672 entries in 25 pages [ 0.049242] net_namespace: 628 bytes [ 0.049381] Booting paravirtualized kernel on bare hardware [ 0.050695] NET: Registered protocol family 16 [ 0.052240] ACPI: bus type pci registered [ 0.052817] PCI: PCI BIOS revision 2.10 entry at 0xe97a4, last bus=2 [ 0.052893] PCI: Using configuration type 1 for base access [ 0.063463] bio: create slab at 0 [ 0.068169] ACPI: EC: Look up EC in DSDT [ 0.083479] ACPI: Interpreter enabled [ 0.083555] ACPI: (supports S0 S1 S3 S4 S5) [ 0.083877] ACPI: Using PIC for interrupt routing [ 0.144570] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62 [ 0.144650] ACPI: EC: driver started in poll mode [ 0.145195] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.145679] pci 0000:00:00.0: reg 10 32bit mmio: [0xb0000000-0xb3ffffff] [ 0.146020] pci 0000:00:1d.0: reg 20 io port: [0x1200-0x121f] [ 0.146128] pci 0000:00:1d.1: reg 20 io port: [0x1600-0x161f] [ 0.146239] pci 0000:00:1d.2: reg 20 io port: [0x1700-0x171f] [ 0.146361] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf4000000-0xf40003ff] [ 0.146472] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.146553] pci 0000:00:1d.7: PME# disabled [ 0.146795] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO [ 0.146905] pci 0000:00:1f.0: quirk: region 1300-133f claimed by ICH4 GPIO [ 0.147028] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07] [ 0.147042] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03] [ 0.147055] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07] [ 0.147068] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03] [ 0.147082] pci 0000:00:1f.1: reg 20 io port: [0x1100-0x110f] [ 0.147095] pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff] [ 0.147199] pci 0000:00:1f.3: reg 20 io port: [0x1400-0x141f] [ 0.147291] pci 0000:00:1f.5: reg 10 io port: [0xe000-0xe0ff] [ 0.147304] pci 0000:00:1f.5: reg 14 io port: [0xe100-0xe13f] [ 0.147318] pci 0000:00:1f.5: reg 18 32bit mmio: [0xf0000400-0xf00005ff] [ 0.147331] pci 0000:00:1f.5: reg 1c 32bit mmio: [0xf0000600-0xf00006ff] [ 0.147394] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold [ 0.147473] pci 0000:00:1f.5: PME# disabled [ 0.147604] pci 0000:00:1f.6: reg 10 io port: [0xe200-0xe2ff] [ 0.147617] pci 0000:00:1f.6: reg 14 io port: [0xe300-0xe37f] [ 0.147698] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold [ 0.147777] pci 0000:00:1f.6: PME# disabled [ 0.147933] pci 0000:01:00.0: reg 10 32bit mmio: [0xa8000000-0xafffffff] [ 0.147945] pci 0000:01:00.0: reg 14 io port: [0xc100-0xc1ff] [ 0.147958] pci 0000:01:00.0: reg 18 32bit mmio: [0xe0010000-0xe001ffff] [ 0.148015] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff] [ 0.148061] pci 0000:01:00.0: supports D1 D2 [ 0.148163] pci 0000:00:01.0: bridge io port: [0xc000-0xdfff] [ 0.148171] pci 0000:00:01.0: bridge 32bit mmio: [0xe0000000-0xefffffff] [ 0.148179] pci 0000:00:01.0: bridge 32bit mmio pref: [0xa0000000-0xafffffff] [ 0.148249] pci 0000:02:00.0: reg 10 32bit mmio: [0xd0001800-0xd0001fff] [ 0.148263] pci 0000:02:00.0: reg 14 io port: [0xa100-0xa17f] [ 0.148346] pci 0000:02:00.0: supports D2 [ 0.148350] pci 0000:02:00.0: PME# supported from D2 D3hot D3cold [ 0.148429] pci 0000:02:00.0: PME# disabled [ 0.148561] pci 0000:02:01.0: reg 10 io port: [0xa000-0xa0ff] [ 0.148575] pci 0000:02:01.0: reg 14 32bit mmio: [0xd0001000-0xd00010ff] [ 0.148657] pci 0000:02:01.0: supports D1 D2 [ 0.148661] pci 0000:02:01.0: PME# supported from D1 D2 D3hot D3cold [ 0.148740] pci 0000:02:01.0: PME# disabled [ 0.148873] pci 0000:02:02.0: reg 10 32bit mmio: [0xd0000000-0xd0000fff] [ 0.148966] pci 0000:02:02.0: PME# supported from D0 D3hot D3cold [ 0.149044] pci 0000:02:02.0: PME# disabled [ 0.149181] pci 0000:02:03.0: reg 10 32bit mmio: [0x90100000-0x90100fff] [ 0.149219] pci 0000:02:03.0: supports D1 D2 [ 0.149223] pci 0000:02:03.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.149303] pci 0000:02:03.0: PME# disabled [ 0.149465] pci 0000:00:1e.0: transparent bridge [ 0.149542] pci 0000:00:1e.0: bridge io port: [0xa000-0xbfff] [ 0.149550] pci 0000:00:1e.0: bridge 32bit mmio: [0xd0000000-0xdfffffff] [ 0.149560] pci 0000:00:1e.0: bridge 32bit mmio pref: [0x90000000-0x9fffffff] [ 0.149617] pci_bus 0000:00: on NUMA node 0 [ 0.149629] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.149932] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] [ 0.150030] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT] [ 0.167093] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10) [ 0.167501] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 10) *11 [ 0.167934] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10) *11 [ 0.168401] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10) *11 [ 0.168845] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 0.169587] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 0.170327] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 0.171066] ACPI: PCI Interrupt Link [LNKH] (IRQs 5 10) *11 [ 0.172427] SCSI subsystem initialized [ 0.172985] usbcore: registered new interface driver usbfs [ 0.173214] usbcore: registered new interface driver hub [ 0.173506] usbcore: registered new device driver usb [ 0.174203] PCI: Using ACPI for IRQ routing [ 0.174406] pci 0000:02:03.0: BAR 0: can't allocate resource [ 0.182938] pnp: PnP ACPI init [ 0.183087] ACPI: bus type pnp registered [ 0.212796] pnp: PnP ACPI: found 11 devices [ 0.212873] ACPI: ACPI bus type pnp unregistered [ 0.212974] system 00:01: ioport range 0x1000-0x107f has been reserved [ 0.213052] system 00:01: ioport range 0x1300-0x133f has been reserved [ 0.213131] system 00:01: ioport range 0x200-0x20f has been reserved [ 0.213208] system 00:01: ioport range 0x4d0-0x4d1 has been reserved [ 0.213285] system 00:01: ioport range 0xfe00-0xfe00 has been reserved [ 0.213363] system 00:01: ioport range 0xff2c-0xff2f has been reserved [ 0.213442] system 00:01: iomem range 0xfff80000-0xffffffff has been reserved [ 0.249725] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 [ 0.249804] pci 0000:00:01.0: IO window: 0xc000-0xdfff [ 0.249883] pci 0000:00:01.0: MEM window: 0xe0000000-0xefffffff [ 0.249962] pci 0000:00:01.0: PREFETCH window: 0x000000a0000000-0x000000afffffff [ 0.250798] pci 0000:02:03.0: CardBus bridge, secondary bus 0000:03 [ 0.250873] pci 0000:02:03.0: IO window: 0x00a400-0x00a4ff [ 0.250952] pci 0000:02:03.0: IO window: 0x00a800-0x00a8ff [ 0.251031] pci 0000:02:03.0: PREFETCH window: 0x90000000-0x93ffffff [ 0.251111] pci 0000:02:03.0: MEM window: 0xd4000000-0xd7ffffff [ 0.251191] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02 [ 0.251267] pci 0000:00:1e.0: IO window: 0xa000-0xbfff [ 0.251348] pci 0000:00:1e.0: MEM window: 0xd0000000-0xdfffffff [ 0.251428] pci 0000:00:1e.0: PREFETCH window: 0x00000090000000-0x0000009fffffff [ 0.251566] pci 0000:00:1e.0: setting latency timer to 64 [ 0.251900] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 [ 0.251976] PCI: setting IRQ 10 as level-triggered [ 0.251983] pci 0000:02:03.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10 [ 0.252119] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.252124] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] [ 0.252129] pci_bus 0000:01: resource 0 io: [0xc000-0xdfff] [ 0.252134] pci_bus 0000:01: resource 1 mem: [0xe0000000-0xefffffff] [ 0.252138] pci_bus 0000:01: resource 2 pref mem [0xa0000000-0xafffffff] [ 0.252143] pci_bus 0000:02: resource 0 io: [0xa000-0xbfff] [ 0.252148] pci_bus 0000:02: resource 1 mem: [0xd0000000-0xdfffffff] [ 0.252152] pci_bus 0000:02: resource 2 pref mem [0x90000000-0x9fffffff] [ 0.252157] pci_bus 0000:02: resource 3 io: [0x00-0xffff] [ 0.252161] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff] [ 0.252166] pci_bus 0000:03: resource 0 io: [0xa400-0xa4ff] [ 0.252170] pci_bus 0000:03: resource 1 io: [0xa800-0xa8ff] [ 0.252174] pci_bus 0000:03: resource 2 pref mem [0x90000000-0x93ffffff] [ 0.252179] pci_bus 0000:03: resource 3 mem: [0xd4000000-0xd7ffffff] [ 0.252368] NET: Registered protocol family 2 [ 0.252893] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.254348] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.256646] TCP bind hash table entries: 65536 (order: 9, 2621440 bytes) [ 0.266687] TCP: Hash tables configured (established 131072 bind 65536) [ 0.266849] TCP reno registered [ 0.267256] NET: Registered protocol family 1 [ 0.268201] Simple Boot Flag at 0x37 set to 0x80 [ 0.276700] msgmni has been set to 1500 [ 0.276967] io scheduler noop registered [ 0.277039] io scheduler anticipatory registered [ 0.277111] io scheduler deadline registered [ 0.277216] io scheduler cfq registered (default) [ 0.277454] pci 0000:01:00.0: Boot video device [ 0.278451] ACPI: AC Adapter [ACAD] (off-line) [ 0.279391] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.279579] ACPI: Power Button [PWRF] [ 0.279934] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input1 [ 0.280074] ACPI: Sleep Button [SLPF] [ 0.280152] ACPI Error (evxfevnt-0193): Could not enable SleepButton event [20090320] [ 0.280326] ACPI Warning (evxface-0146): Could not enable fixed event 3 [20090320] [ 0.280993] button: probe of LNXSLPBN:00 failed with error -22 [ 0.281344] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 [ 0.281535] ACPI: Lid Switch [LID] [ 0.281888] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 [ 0.281999] ACPI: Power Button [PWRB] [ 0.282792] Marking TSC unstable due to TSC halts in idle [ 0.283392] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3]) [ 0.284207] Switched to high resolution mode on CPU 0 [ 0.284263] processor ACPI_CPU:00: registered as cooling_device0 [ 0.284346] ACPI: Processor [CPU0] (supports 8 throttling states) [ 0.297499] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.298644] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.299296] Platform driver 'serial8250' needs updating - please use dev_pm_ops [ 0.300389] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 [ 0.300469] serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 0.300588] serial 0000:00:1f.6: PCI INT B disabled [ 0.306198] ACPI: Battery Slot [BAT1] (battery present) [ 0.310154] brd: module loaded [ 0.310359] Uniform Multi-Platform E-IDE driver [ 0.310755] piix 0000:00:1f.1: IDE controller (0x8086:0x24ca rev 0x03) [ 0.310843] PIIX_IDE 0000:00:1f.1: enabling device (0005 -> 0007) [ 0.310929] PIIX_IDE 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10 [ 0.311172] piix 0000:00:1f.1: not 100% native mode: will probe irqs later [ 0.311255] ide0: BM-DMA at 0x1100-0x1107 [ 0.311421] ide1: BM-DMA at 0x1108-0x110f [ 0.311516] Probing IDE interface ide0... [ 0.600290] hda: HTS548060M9AT00, ATA DISK drive [ 1.272343] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 1.272576] hda: UDMA/100 mode selected [ 1.272877] Probing IDE interface ide1... [ 2.008282] hdc: QSI CD-RW/DVD-ROM SBW-242, ATAPI CD/DVD-ROM drive [ 2.680228] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 2.680325] hdc: UDMA/33 mode selected [ 2.680566] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 2.680803] ide1 at 0x170-0x177,0x376 on irq 15 [ 2.681626] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports [ 2.681736] ide-gd driver 1.18 [ 2.681845] hda: max request size: 512KiB [ 2.704387] hda: 117210240 sectors (60011 MB) w/7877KiB Cache, CHS=16383/255/63 [ 2.704901] hda: cache flushes supported [ 2.705282] hda: hda1 hda2 hda3 hda4 < hda5 hda6 > [ 2.751260] ide-cd driver 5.00 [ 2.752846] ide-cd: hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache [ 2.753088] Uniform CD-ROM driver Revision: 3.20 [ 2.765080] Driver 'sd' needs updating - please use bus_type methods [ 2.765328] 8139too Fast Ethernet driver 0.9.28 [ 2.765776] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 [ 2.765854] 8139too 0000:02:01.0: PCI INT A -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10 [ 2.767411] eth0: RealTek RTL8139 at 0xf0814000, 00:02:3f:17:bd:36, IRQ 10 [ 2.767488] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 2.768089] console [netcon0] enabled [ 2.768162] netconsole: network logging started [ 2.768788] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.769231] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10 [ 2.769308] ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 10 (level, low) -> IRQ 10 [ 2.769431] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.769438] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.771949] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.776060] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.776140] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 2.776159] ehci_hcd 0000:00:1d.7: irq 10, io mem 0xf4000000 [ 2.792040] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.792829] usb usb1: configuration #1 chosen from 1 choice [ 2.793432] hub 1-0:1.0: USB hub found [ 2.793657] hub 1-0:1.0: 6 ports detected [ 2.795404] uhci_hcd: USB Universal Host Controller Interface driver [ 2.795878] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 [ 2.795955] uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 2.796140] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.796147] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.796605] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.796742] uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001200 [ 2.797199] usb usb2: configuration #1 chosen from 1 choice [ 2.797475] hub 2-0:1.0: USB hub found [ 2.797661] hub 2-0:1.0: 2 ports detected [ 2.798282] uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10 [ 2.798400] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.798406] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.798913] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.799049] uhci_hcd 0000:00:1d.1: irq 10, io base 0x00001600 [ 2.799510] usb usb3: configuration #1 chosen from 1 choice [ 2.799790] hub 3-0:1.0: USB hub found [ 2.799876] hub 3-0:1.0: 2 ports detected [ 2.800496] uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10 [ 2.800613] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.800619] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.801098] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.801234] uhci_hcd 0000:00:1d.2: irq 10, io base 0x00001700 [ 2.801696] usb usb4: configuration #1 chosen from 1 choice [ 2.801974] hub 4-0:1.0: USB hub found [ 2.802064] hub 4-0:1.0: 2 ports detected [ 2.803117] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 2.803331] Platform driver 'i8042' needs updating - please use dev_pm_ops [ 2.804063] i8042.c: Detected active multiplexing controller, rev 1.1. [ 2.804202] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.804346] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 2.804464] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 2.804541] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 2.804617] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 2.805197] mice: PS/2 mouse device common for all mice [ 2.808658] cpuidle: using governor ladder [ 2.810213] cpuidle: using governor menu [ 2.811968] TCP cubic registered [ 2.812259] NET: Registered protocol family 17 [ 2.812424] Using IPI Shortcut mode [ 2.813322] PM: Checking image partition /dev/hda5 [ 2.813383] PM: Resume from partition 3:5 [ 2.813386] PM: Checking hibernation image. [ 2.825544] PM: Resume from disk failed. [ 3.380195] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x254ab1, caps: 0x804713/0x0 [ 3.411688] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input4 [ 3.417842] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5 [ 3.436128] REISERFS (device hda6): found reiserfs format "3.6" with standard journal [ 3.436322] REISERFS (device hda6): using ordered data mode [ 3.445740] REISERFS (device hda6): journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 3.446597] REISERFS (device hda6): checking transaction log (hda6) [ 3.526543] REISERFS (device hda6): Using r5 hash to sort names [ 3.579130] VFS: Mounted root (reiserfs filesystem) readonly on device 3:6. [ 3.579425] Freeing unused kernel memory: 268k freed