lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date:	Thu, 23 Jun 2011 22:00:29 -0600
From:	Grant Likely <grant.likely@...retlab.ca>
To:	David Daney <david.daney@...ium.com>
Cc:	linux-mips@...ux-mips.org, ralf@...ux-mips.org,
	devicetree-discuss@...ts.ozlabs.org, linux-kernel@...r.kernel.org,
	David Daney <ddaney@...iumnetworks.com>
Subject: Re: [RFC PATCH] MIPS: Octeon: Add device tree source files.

On Thu, Jun 23, 2011 at 6:42 PM, David Daney <david.daney@...ium.com> wrote:
> From: David Daney <ddaney@...iumnetworks.com>
>
> Signed-off-by: David Daney <ddaney@...iumnetworks.com>
> ---
>
> This is a revision of my main device-tree definitions from my previous
> RFC.  I wanted to get feedback on my changes to several bindings
> before I set them in stone.
>
> The changes are to bootbus.txt, compact-flash.txt and dma-engine.txt.
>
> Basically there are a ton of parameters needed to initialize the boot
> bus, and I just stuck them all in there.  Is this the best way to
> handle something like this?
>
> I look forward to hearing any feedback.

Mostly looks good.  Comments below.

g.

>
> Thanks,
> David Daney
>
>  .../devicetree/bindings/mips/cavium/bootbus.txt    |  114 +++++
>  .../devicetree/bindings/mips/cavium/ciu.txt        |   26 ++
>  .../bindings/mips/cavium/compact-flash.txt         |   31 ++
>  .../devicetree/bindings/mips/cavium/dma-engine.txt |   21 +
>  .../devicetree/bindings/mips/cavium/gpio.txt       |   48 ++

should be .../bindings/gpio/cavium.txt

>  .../devicetree/bindings/mips/cavium/mdio.txt       |   27 ++

.../bindings/net/mdio.txt

and so on.

>  .../devicetree/bindings/mips/cavium/mix.txt        |   40 ++
>  .../devicetree/bindings/mips/cavium/pip.txt        |   98 +++++
>  .../devicetree/bindings/mips/cavium/twsi.txt       |   34 ++
>  .../devicetree/bindings/mips/cavium/uart.txt       |   19 +
>  .../devicetree/bindings/mips/cavium/uctl.txt       |   47 ++
>  arch/mips/cavium-octeon/.gitignore                 |    2 +
>  arch/mips/cavium-octeon/Makefile                   |   13 +
>  arch/mips/cavium-octeon/octeon_3xxx.dts            |  452 ++++++++++++++++++++
>  14 files changed, 972 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/bootbus.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/ciu.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/compact-flash.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/gpio.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/mdio.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/mix.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/pip.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/twsi.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/uart.txt
>  create mode 100644 Documentation/devicetree/bindings/mips/cavium/uctl.txt
>  create mode 100644 arch/mips/cavium-octeon/.gitignore
>  create mode 100644 arch/mips/cavium-octeon/octeon_3xxx.dts
>
> diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
> new file mode 100644
> index 0000000..2960ba8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
> @@ -0,0 +1,114 @@
> +* Boot Bus
> +
> +The Octeon Boot Bus is a configurable parallel bus with 8 chip
> +selects.  Each chip select is independently configurable.
> +
> +Properties:
> +- compatible: "cavium,octeon-3860-bootbus"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The base address of the Boot Bus' register bank.
> +
> +- #address-cells: Must be <2>.  The first cell is the chip select
> +   within the bootbus.  The second cell is the offset from the chip select.
> +
> +- #size-cells: Must be <1>.
> +
> +- ranges: There must be one one triplet of (child-bus-address,
> +  parent-bus-address, length) for each active chip select.  If the
> +  length element for any triplet is zero, the chip select is disabled,
> +  making it inactive.

You don't need to actually define standard properties like 'ranges'.
You can save some text that way.

> +
> +- t-adr: An array of 8 elements specifying the ADR timing parameter
> +  (in nS) for the each of the 8 chip selects.

Using arrays like this is a little awkward.  Particularly if board
code needs to modify only one CS configuration; it then needs to
replace /all/ of the configuration values because there is no way for
DTC to modify a portion of property data.  You may want to consider a
set of CS configuration child nodes with the parameters as properties.

Also, these property names are pretty terse.  They should probably
carry a "cavium," prefix, and you can use longer names.

> +
> +- t-ce: An array of 8 elements specifying the CE timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-oe: An array of 8 elements specifying the OE timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-we: An array of 8 elements specifying the WE timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-rd-hld: An array of 8 elements specifying the RD_HLD timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-wr-hld: An array of 8 elements specifying the WR_HLD timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-pause: An array of 8 elements specifying the PAUSE timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-wait: An array of 8 elements specifying the WAIT timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-page: An array of 8 elements specifying the PAGE timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- t-rd-dly: An array of 8 elements specifying the RD_DLY timing parameter
> +  (in nS) for the each of the 8 chip selects.
> +
> +- pages: An array of 8 elements specifying the PAGES parameter (0 = 8
> +  bytes, 1 = 2 bytes, 2 = 4 bytes, 3 = 8 bytes) for the each of the 8
> +  chip selects.
> +
> +- wait-mode: An array of 8 elements specifying the WAITM parameter
> +  (0 or 1) for the each of the 8 chip selects.
> +
> +- page-mode: An array of 8 elements specifying the PAGEM parameter
> +  (0 or 1) for the each of the 8 chip selects.
> +
> +- bus-width: An array of 8 elements specifying the WIDTH parameter
> +  (in bits) for the each of the 8 chip selects.
> +
> +- ale-mode: An array of 8 elements specifying the ALE parameter
> +  (0 or 1) for the each of the 8 chip selects.
> +
> +- sam-mode: An array of 8 elements specifying the SAM parameter
> +  (0 or 1) for the each of the 8 chip selects.
> +
> +- or-mode: An array of 8 elements specifying the OR parameter
> +  (0 or 1) for the each of the 8 chip selects.
> +
> +
> +Example:
> +       bootbus: bootbus@...0000000000 {
> +               compatible = "cavium,octeon-3860-bootbus";
> +               reg = <0x11800 0x00000000 0x0 0x200>;
> +               /* The chip select number and offset */
> +               #address-cells = <2>;
> +               /* The size of the chip select region */
> +               #size-cells = <1>;
> +               ranges = <0 0  0x0 0x1f400000  0xc00000>,
> +                        <1 0  0x10000 0x30000000  0>,
> +                        <2 0  0x10000 0x40000000  0>,
> +                        <3 0  0x10000 0x50000000  0>,
> +                        <4 0  0x0 0x1d020000  0x10000>,
> +                        <5 0  0x0 0x1d040000  0x10000>,
> +                        <6 0  0x0 0x1d050000  0x10000>,
> +                        <7 0  0x10000 0x90000000  0>;
> +
> +               t-adr    = <20 0 0 0 320   5   5 0>;
> +               t-ce     = <60 0 0 0 320 300 300 0>;
> +               t-oe     = <60 0 0 0 320 125 270 0>;
> +               t-we     = <45 0 0 0 320 150 150 0>;
> +               t-rd-hld = <35 0 0 0 320 100 100 0>;
> +               t-wr-hld = <45 0 0 0 320  30  70 0>;
> +               t-pause  = < 0 0 0 0 320   0   0 0>;
> +               t-wait   = < 0 0 0 0 320  30   0 0>;
> +               t-page   = <35 0 0 0 320 320 320 0>;
> +               t-rd-dly = < 0 0 0 0   0   0   0 0>;
> +
> +               pages     = <0 0 0 0 0  0  0 0>;
> +               wait-mode = <0 0 0 0 0  1  0 0>;
> +               page-mode = <0 0 0 0 0  0  0 0>;
> +               bus-width = <8 8 8 8 8 16 16 8>;
> +               ale-mode  = <0 0 0 0 0  0  0 0>;
> +               sam-mode  = <0 0 0 0 0  0  0 0>;
> +               or-mode   = <0 0 0 0 0  0  0 0>;
> +               .
> +               .
> +               .
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu.txt b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
> new file mode 100644
> index 0000000..c8ff212
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
> @@ -0,0 +1,26 @@
> +* Central Interrupt Unit
> +
> +Properties:
> +- compatible: "cavium,octeon-3860-ciu"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs.
> +
> +- interrupt-controller:  This is an interrupt controller.
> +
> +- reg: The base address of the CIU's register bank.
> +
> +- #interrupt-cells: Must be <2>.  The first cell is the bank within
> +   the CIU and may have a value of 0 or 1.  The second cell is the bit
> +   within the bank and may have a value between 0 and 63.

Is there any edge/level high/low configuration on these interrupt
lines?  If so, then you'll want a third cell for flags.  (I may have
already asked you this question)

> +
> +Example:
> +       interrupt-controller@...0000000000 {
> +               compatible = "cavium,octeon-3860-ciu";
> +               interrupt-controller;
> +               /* Interrupts are specified by two parts:
> +                * 1) Controller register (0 or 1)
> +                * 2) Bit within the register (0..63)
> +                */
> +               #interrupt-cells = <2>;
> +               reg = <0x10700 0x00000000 0x0 0x7000>;
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/compact-flash.txt b/Documentation/devicetree/bindings/mips/cavium/compact-flash.txt
> new file mode 100644
> index 0000000..84972a3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/compact-flash.txt
> @@ -0,0 +1,31 @@
> +* Compact Flash
> +
> +The Cavium Compact Flash device is connected to the Octeon Boot Bus,
> +and is thus a child of the Boot Bus device.  It can read and write
> +industry standard compact flash devices.
> +
> +Properties:
> +- compatible: "cavium,ebt3000-compact-flash";
> +
> +  Compatibility with many Cavium evaluation boards.
> +
> +- reg: The base address of the the CF chip select banks.  Depending on
> +  the device configuration, there may be one or two banks.
> +
> +- bus-width: The width of the connection to the CF devices.  Valid
> +  values are 8 and 16.
> +
> +- true-ide: Mode of the CF connection.  Valid values are 1 - True IDE,
> +  0 - not True IDE.

Often, booleans like this are encoded based on whether or not the
property is present.  ie. "cavium,true-ide;" turns on true-ide mode.

> +
> +- dma-engine-handle: Optional, a phandle for the DMA Engine connected
> +  to this device.

In general, if you're defining new device-specific properties, it is
good practice to prefix them with "cavium,"

> +
> +Example:
> +       compact-flash@5,0 {
> +               compatible = "cavium,ebt3000-compact-flash";
> +               reg = <5 0 0x10000>, <6 0 0x10000>;
> +               bus-width = <16>;
> +               true-ide = <1>;
> +               dma-engine-handle = <&dma0>;
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
> new file mode 100644
> index 0000000..cb4291e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
> @@ -0,0 +1,21 @@
> +* DMA Engine.
> +
> +The Octeon DMA Engine transfers between the Boot Bus and main memory.
> +The DMA Engine will be refered to by phandle by any device that is
> +connected to it.
> +
> +Properties:
> +- compatible: "cavium,octeon-5750-bootbus-dma"
> +
> +  Compatibility with all cn52XX, cn56XX and cn6XXX SOCs.
> +
> +- reg: The base address of the DMA Engine's register bank.
> +
> +- interrupts: A single interrupt specifier.
> +
> +Example:
> +       dma0: dma-engine@...0000000100 {
> +               compatible = "cavium,octeon-5750-bootbus-dma";
> +               reg = <0x11800 0x00000100 0x0 0x8>;
> +               interrupts = <0 63>;
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/gpio.txt b/Documentation/devicetree/bindings/mips/cavium/gpio.txt
> new file mode 100644
> index 0000000..21b989a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/gpio.txt
> @@ -0,0 +1,48 @@
> +* General Purpose Input Output (GPIO) bus.
> +
> +Properties:
> +- compatible: "cavium,octeon-3860-gpio"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The base address of the GPIO unit's register bank.
> +
> +- gpio-controller: This is a GPIO controller.
> +
> +- #gpio-cells: Must be <2>.  The first cell is the GPIO pin.

Should also state what the meaning of the 2nd cell is.

> +
> +- interrupt-controller: The GPIO controller is also an interrupt
> +  controller, any of its pins may be configured as an interrupt
> +  source.
> +
> +- #interrupt-cells: Must be <2>.  The first cell is the GPIO pin
> +   connected to the interrupt source.  The second cell is the interrupt
> +   triggering protocol and may have one of four values:
> +   1 - edge triggered on the rising edge.
> +   2 - edge triggered on the falling edge
> +   4 - level triggered active high.
> +   8 - level triggered active low.
> +
> +- interrupts: Interrupt routing for pin 0.  The remaining pins are
> +  also routed, but in a manner that can be derived from the pin0
> +  routing, so they are not specified.
> +
> +Example:
> +
> +       gpio-controller@...0000000800 {
> +               #gpio-cells = <2>;
> +               compatible = "cavium,octeon-3860-gpio";
> +               reg = <0x10700 0x00000800 0x0 0x100>;
> +               gpio-controller;
> +               /* Interrupts are specified by two parts:
> +                * 1) GPIO pin number (0..15)
> +                * 2) Triggering (1 - edge rising
> +                *                2 - edge falling
> +                *                4 - level active high
> +                *                8 - level active low)
> +                */
> +               interrupt-controller;
> +               #interrupt-cells = <2>;
> +               /* The GPIO pin connect to 16 consecutive CUI bits */
> +               interrupts = <0 16>;
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/mdio.txt b/Documentation/devicetree/bindings/mips/cavium/mdio.txt
> new file mode 100644
> index 0000000..6253c3b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/mdio.txt
> @@ -0,0 +1,27 @@
> +* System Management Interface (SMI) / MDIO
> +
> +Properties:
> +- compatible: "cavium,octeon-3860-mdio"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The base address of the MDIO bus controller register bank.
> +
> +- #address-cells: Must be <1>.
> +
> +- #size-cells: Must be <0>.  MDIO addresses have no size component.
> +
> +Typically an MDIO bus might have several children.
> +
> +Example:
> +       mdio@...0000001800 {
> +               compatible = "cavium,octeon-3860-mdio";
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               reg = <0x11800 0x00001800 0x0 0x40>;
> +
> +               ethernet-phy@0 {
> +                       ...
> +                       reg = <0>;
> +               };
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/mix.txt b/Documentation/devicetree/bindings/mips/cavium/mix.txt
> new file mode 100644
> index 0000000..2a91a33
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/mix.txt
> @@ -0,0 +1,40 @@
> +* MIX Ethernet controller.
> +
> +Properties:
> +- compatible: "cavium,octeon-5750-mix"
> +
> +  Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX
> +  devices.
> +
> +- reg: The base addresses of four seperate register banks.  The first

sp.  separate.

> +  bank contains the MIX registers.  The second bank the corresponding
> +  AGL registers.  The third bank are the AGL registers shared by all
> +  MIX devices present.  The fourth bank is the AGL_PRT_CTL shared by
> +  all MIX devices present.
> +
> +- cell-index: A single cell specifying which portion of the shared
> +  register banks corresponds to this MIX device.
> +
> +- interrupts: Two interrupt specifiers.  The first is the MIX
> +  interrupt routing and the second the routing for the AGL interrupts.
> +
> +- mac-address: Optional, the MAC address to assign to the device.
> +
> +- local-mac-address: Optional, the MAC address to assign to the device
> +  if mac-address is not specified.
> +
> +- phy-handle: Optional, a phandle for the PHY device connected to this device.
> +
> +Example:
> +       ethernet@...0000100800 {
> +               compatible = "cavium,octeon-5750-mix";
> +               reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
> +                     <0x11800 0xE0000800 0x0 0x300>, /* AGL */
> +                     <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
> +                     <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
> +               cell-index = <1>;
> +               interrupts = <1 18>, < 1 46>;
> +               local-mac-address = [ 00 0f b7 10 63 54 ];
> +               phy-handle = <&phy1>;
> +       };
> +
> diff --git a/Documentation/devicetree/bindings/mips/cavium/pip.txt b/Documentation/devicetree/bindings/mips/cavium/pip.txt
> new file mode 100644
> index 0000000..d4c53ba
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/pip.txt
> @@ -0,0 +1,98 @@
> +* PIP Ethernet nexus.
> +
> +The PIP Ethernet nexus can control several data packet input/output
> +devices.  The devices have a two level grouping scheme.  There may be
> +several interfaces, and each interface may have several ports.  These
> +ports might be an individual Ethernet PHY.
> +
> +
> +Properties for the PIP nexus:
> +- compatible: "cavium,octeon-3860-pip"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The base address of the PIP's register bank.
> +
> +- #address-cells: Must be <1>.
> +
> +- #size-cells: Must be <0>.
> +
> +Properties for PIP interfaces which is a child the PIP nexus:
> +- compatible: "cavium,octeon-3860-pip-interface"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The interface number.
> +
> +- #address-cells: Must be <1>.
> +
> +- #size-cells: Must be <0>.
> +
> +Properties for PIP port which is a child the PIP interface:
> +- compatible: "cavium,octeon-3860-pip-port"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The port number within the interface group.
> +
> +- mac-address: Optional, the MAC address to assign to the device.
> +
> +- local-mac-address: Optional, the MAC address to assign to the device
> +  if mac-address is not specified.
> +
> +- phy-handle: Optional, a phandle for the PHY device connected to this device.
> +
> +Example:
> +
> +       pip@...00a0000000 {
> +               compatible = "cavium,octeon-3860-pip";
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               reg = <0x11800 0xa0000000 0x0 0x2000>;
> +
> +               interface@0 {
> +                       compatible = "cavium,octeon-3860-pip-interface";
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       reg = <0>; /* interface */
> +
> +                       ethernet@0 {
> +                               compatible = "cavium,octeon-3860-pip-port";
> +                               reg = <0x0>; /* Port */
> +                               local-mac-address = [ 00 0f b7 10 63 60 ];
> +                               phy-handle = <&phy2>;
> +                       };
> +                       ethernet@1 {
> +                               compatible = "cavium,octeon-3860-pip-port";
> +                               reg = <0x1>; /* Port */
> +                               local-mac-address = [ 00 0f b7 10 63 61 ];
> +                               phy-handle = <&phy3>;
> +                       };
> +                       ethernet@2 {
> +                               compatible = "cavium,octeon-3860-pip-port";
> +                               reg = <0x2>; /* Port */
> +                               local-mac-address = [ 00 0f b7 10 63 62 ];
> +                               phy-handle = <&phy4>;
> +                       };
> +                       ethernet@3 {
> +                               compatible = "cavium,octeon-3860-pip-port";
> +                               reg = <0x3>; /* Port */
> +                               local-mac-address = [ 00 0f b7 10 63 63 ];
> +                               phy-handle = <&phy5>;
> +                       };
> +               };
> +
> +               interface@1 {
> +                       compatible = "cavium,octeon-3860-pip-interface";
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       reg = <1>; /* interface */
> +
> +                       ethernet@0 {
> +                               compatible = "cavium,octeon-3860-pip-port";
> +                               reg = <0x0>; /* Port */
> +                               local-mac-address = [ 00 0f b7 10 63 64 ];
> +                               phy-handle = <&phy6>;
> +                       };
> +               };
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/twsi.txt b/Documentation/devicetree/bindings/mips/cavium/twsi.txt
> new file mode 100644
> index 0000000..6e57155
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/twsi.txt
> @@ -0,0 +1,34 @@
> +* Two Wire Serial Interface (TWSI) / I2C
> +
> +- compatible: "cavium,octeon-3860-twsi"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The base address of the TWSI/I2C bus controller register bank.
> +
> +- #address-cells: Must be <1>.
> +
> +- #size-cells: Must be <0>.  I2C addresses have no size component.
> +
> +- interrupts: A single interrupt specifier.
> +
> +- clock-rate: The I2C bus clock rate in Hz.
> +
> +Example:
> +       twsi0: i2c@...0000001000 {
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               compatible = "cavium,octeon-3860-twsi";
> +               reg = <0x11800 0x00001000 0x0 0x200>;
> +               interrupts = <0 45>;
> +               clock-rate = <100000>;
> +
> +               rtc@68 {
> +                       compatible = "dallas,ds1337";
> +                       reg = <0x68>;
> +               };
> +               tmp@4c {
> +                       compatible = "ti,tmp421";
> +                       reg = <0x4c>;
> +               };
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/uart.txt b/Documentation/devicetree/bindings/mips/cavium/uart.txt
> new file mode 100644
> index 0000000..87a6c37
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/uart.txt
> @@ -0,0 +1,19 @@
> +* Universal Asynchronous Receiver/Transmitter (UART)
> +
> +- compatible: "cavium,octeon-3860-uart"
> +
> +  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
> +
> +- reg: The base address of the UART register bank.
> +
> +- interrupts: A single interrupt specifier.
> +
> +- current-speed: Optional, the current bit rate in bits per second.
> +
> +Example:
> +       uart1: serial@...0000000c00 {
> +               compatible = "cavium,octeon-3860-uart","ns16550";
> +               reg = <0x11800 0x00000c00 0x0 0x400>;
> +               current-speed = <115200>;
> +               interrupts = <0 35>;
> +       };
> diff --git a/Documentation/devicetree/bindings/mips/cavium/uctl.txt b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
> new file mode 100644
> index 0000000..5dabe02
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
> @@ -0,0 +1,47 @@
> +* UCTL USB controller glue
> +
> +Properties:
> +- compatible: "cavium,octeon-6335-uctl"
> +
> +  Compatibility with all cn6XXX SOCs.
> +
> +- reg: The base address of the UCTL register bank.
> +
> +- #address-cells: Must be <2>.
> +
> +- #size-cells: Must be <2>.
> +
> +- ranges: Empty to signify direct mapping of the children.
> +
> +- refclk-frequency: A single cell containing the reference clock
> +  frequency in Hz.
> +
> +- refclk-type: A string describing the reference clock connection
> +  either "crystal" or "external".
> +
> +Example:
> +       uctl@...006f000000 {
> +               compatible = "cavium,octeon-6335-uctl";
> +               reg = <0x11800 0x6f000000 0x0 0x100>;
> +               ranges; /* Direct mapping */
> +               #address-cells = <2>;
> +               #size-cells = <2>;
> +               /* 12MHz, 24MHz and 48MHz allowed */
> +               refclk-frequency = <24000000>;
> +               /* Either "crystal" or "external" */
> +               refclk-type = "crystal";
> +
> +               ehci@...0000000000 {
> +                       compatible = "cavium,octeon-6335-ehci","usb-ehci";
> +                       reg = <0x16f00 0x00000000 0x0 0x100>;
> +                       interrupts = <0 56>;
> +                       big-endian-regs;
> +               };
> +               ohci@...0000000400 {
> +                       compatible = "cavium,octeon-6335-ohci","usb-ohci";
> +                       reg = <0x16f00 0x00000400 0x0 0x100>;
> +                       interrupts = <0 56>;
> +                       big-endian-regs;
> +               };
> +       };
> +
> diff --git a/arch/mips/cavium-octeon/.gitignore b/arch/mips/cavium-octeon/.gitignore
> new file mode 100644
> index 0000000..39c9686
> --- /dev/null
> +++ b/arch/mips/cavium-octeon/.gitignore
> @@ -0,0 +1,2 @@
> +*.dtb.S
> +*.dtb
> diff --git a/arch/mips/cavium-octeon/Makefile b/arch/mips/cavium-octeon/Makefile
> index 19eb043..b8d4f63 100644
> --- a/arch/mips/cavium-octeon/Makefile
> +++ b/arch/mips/cavium-octeon/Makefile
> @@ -15,3 +15,16 @@ obj-y += octeon-memcpy.o
>  obj-y += executive/
>
>  obj-$(CONFIG_SMP)                     += smp.o
> +
> +DTS_FILES = octeon_3xxx.dts
> +DTB_FILES = $(patsubst %.dts, %.dtb, $(DTS_FILES))
> +
> +obj-y += $(patsubst %.dts, %.dtb.o, $(DTS_FILES))
> +
> +$(obj)/%.dtb: $(src)/%.dts
> +       $(call cmd,dtc)
> +
> +# Let's keep the .dtb files around in case we want to look at them.
> +.SECONDARY:  $(addprefix $(obj)/, $(DTB_FILES))
> +
> +clean-files += $(DTB_FILES) $(patsubst %.dtb, %.dtb.S, $(DTB_FILES))
> diff --git a/arch/mips/cavium-octeon/octeon_3xxx.dts b/arch/mips/cavium-octeon/octeon_3xxx.dts
> new file mode 100644
> index 0000000..a6afd21
> --- /dev/null
> +++ b/arch/mips/cavium-octeon/octeon_3xxx.dts
> @@ -0,0 +1,452 @@
> +/dts-v1/;
> +/*
> + * OCTEON 3XXX, 5XXX, 63XX device tree skeleton.
> + *
> + * This device tree is pruned and patched by early boot code before
> + * use.  Because of this, it contains a super-set of the available
> + * devices and properties.
> + */
> +/ {
> +       compatible = "cavium,octeon-3860";
> +       #address-cells = <2>;
> +       #size-cells = <2>;
> +       interrupt-parent = <&ciu>;
> +
> +       soc@0 {
> +               compatible = "simple-bus";
> +               #address-cells = <2>;
> +               #size-cells = <2>;
> +               ranges; /* Direct mapping */
> +
> +               ciu: interrupt-controller@...0000000000 {
> +                       compatible = "cavium,octeon-3860-ciu";
> +                       interrupt-controller;
> +                       /* Interrupts are specified by two parts:
> +                        * 1) Controller register (0 or 1)
> +                        * 2) Bit within the register (0..63)
> +                        */
> +                       #interrupt-cells = <2>;
> +                       reg = <0x10700 0x00000000 0x0 0x7000>;
> +               };
> +
> +               gpio: gpio-controller@...0000000800 {
> +                       #gpio-cells = <2>;
> +                       compatible = "cavium,octeon-3860-gpio";
> +                       reg = <0x10700 0x00000800 0x0 0x100>;
> +                       gpio-controller;
> +                       /* Interrupts are specified by two parts:
> +                        * 1) GPIO pin number (0..15)
> +                        * 2) Triggering (1 - edge rising
> +                        *                2 - edge falling
> +                        *                4 - level active high
> +                        *                8 - level active low)
> +                        */
> +                       interrupt-controller;
> +                       #interrupt-cells = <2>;
> +                       /* The GPIO pin connect to 16 consecutive CUI bits */
> +                       interrupts = <0 16>; /* <0 17> <0 18> <0 19>
> +                                    <0 20> <0 21> <0 22> <0 23>
> +                                    <0 24> <0 25> <0 26> <0 27>
> +                                    <0 28> <0 29> <0 30> <0 31>; */
> +               };
> +
> +               smi0: mdio@...0000001800 {
> +                       compatible = "cavium,octeon-3860-mdio";
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       reg = <0x11800 0x00001800 0x0 0x40>;
> +
> +                       phy0: ethernet-phy@0 {
> +                               compatible = "broadcom,bcm5241";
> +                               reg = <0>;
> +                       };
> +
> +                       phy1: ethernet-phy@1 {
> +                               compatible = "broadcom,bcm5241";
> +                               reg = <1>;
> +                       };
> +
> +                       phy2: ethernet-phy@2 {
> +                               reg = <2>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +                       phy3: ethernet-phy@3 {
> +                               reg = <3>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +                       phy4: ethernet-phy@4 {
> +                               reg = <4>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +                       phy5: ethernet-phy@5 {
> +                               reg = <5>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +
> +                       phy6: ethernet-phy@6 {
> +                               reg = <6>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +                       phy7: ethernet-phy@7 {
> +                               reg = <7>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +                       phy8: ethernet-phy@8 {
> +                               reg = <8>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +                       phy9: ethernet-phy@9 {
> +                               reg = <9>;
> +                               compatible = "marvell,88e1149r";
> +                               marvell,reg-init = <3 0x10 0 0x5777>,
> +                                       <3 0x11 0 0x00aa>,
> +                                       <3 0x12 0 0x4105>,
> +                                       <3 0x13 0 0x0a60>;
> +                       };
> +               };
> +
> +               smi1: mdio@...0000001900 {
> +                       compatible = "cavium,octeon-3860-mdio";
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       reg = <0x11800 0x00001900 0x0 0x40>;
> +               };
> +
> +               mix0: ethernet@...0000100000 {
> +                       compatible = "cavium,octeon-5750-mix";
> +                       reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
> +                             <0x11800 0xE0000000 0x0 0x300>, /* AGL */
> +                             <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
> +                             <0x11800 0xE0002000 0x0 0x8>;   /* AGL_PRT_CTL */
> +                       cell-index = <0>;
> +                       interrupts = <0 62>, <1 46>;
> +                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                       phy-handle = <&phy0>;
> +               };
> +
> +               mix1: ethernet@...0000100800 {
> +                       compatible = "cavium,octeon-5750-mix";
> +                       reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
> +                             <0x11800 0xE0000800 0x0 0x300>, /* AGL */
> +                             <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
> +                             <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
> +                       cell-index = <1>;
> +                       interrupts = <1 18>, < 1 46>;
> +                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                       phy-handle = <&phy1>;
> +               };
> +
> +               pip: pip@...00a0000000 {
> +                       compatible = "cavium,octeon-3860-pip";
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       reg = <0x11800 0xa0000000 0x0 0x2000>;
> +
> +                       interface@0 {
> +                               compatible = "cavium,octeon-3860-pip-interface";
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               reg = <0>; /* interface */
> +
> +                               ethernet@0 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x0>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy2>;
> +                               };
> +                               ethernet@1 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x1>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy3>;
> +                               };
> +                               ethernet@2 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x2>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy4>;
> +                               };
> +                               ethernet@3 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x3>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy5>;
> +                               };
> +                               ethernet@4 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x4>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@5 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x5>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@6 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x6>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@7 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x7>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@8 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x8>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@9 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x9>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@a {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0xa>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@b {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0xb>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@c {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0xc>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@d {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0xd>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@e {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0xe>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                               ethernet@f {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0xf>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                               };
> +                       };
> +
> +                       interface@1 {
> +                               compatible = "cavium,octeon-3860-pip-interface";
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               reg = <1>; /* interface */
> +
> +                               ethernet@0 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x0>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy6>;
> +                               };
> +                               ethernet@1 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x1>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy7>;
> +                               };
> +                               ethernet@2 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x2>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy8>;
> +                               };
> +                               ethernet@3 {
> +                                       compatible = "cavium,octeon-3860-pip-port";
> +                                       reg = <0x3>; /* Port */
> +                                       local-mac-address = [ 00 00 00 00 00 00 ];
> +                                       phy-handle = <&phy9>;
> +                               };
> +                       };
> +               };
> +
> +               twsi0: i2c@...0000001000 {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       compatible = "cavium,octeon-3860-twsi";
> +                       reg = <0x11800 0x00001000 0x0 0x200>;
> +                       interrupts = <0 45>;
> +                       clock-rate = <100000>;
> +
> +                       rtc@68 {
> +                               compatible = "dallas,ds1337";
> +                               reg = <0x68>;
> +                       };
> +                       tmp@4c {
> +                               compatible = "ti,tmp421";
> +                               reg = <0x4c>;
> +                       };
> +               };
> +
> +               twsi1: i2c@...0000001200 {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       compatible = "cavium,octeon-3860-twsi";
> +                       reg = <0x11800 0x00001200 0x0 0x200>;
> +                       interrupts = <0 59>;
> +                       clock-rate = <100000>;
> +               };
> +
> +               uart0: serial@...0000000800 {
> +                       compatible = "cavium,octeon-3860-uart","ns16550";
> +                       reg = <0x11800 0x00000800 0x0 0x400>;
> +                       clock-frequency = <0>;
> +                       current-speed = <115200>;
> +                       reg-shift = <3>;
> +                       interrupts = <0 34>;
> +               };
> +
> +               uart1: serial@...0000000c00 {
> +                       compatible = "cavium,octeon-3860-uart","ns16550";
> +                       reg = <0x11800 0x00000c00 0x0 0x400>;
> +                       clock-frequency = <0>;
> +                       current-speed = <115200>;
> +                       reg-shift = <3>;
> +                       interrupts = <0 35>;
> +               };
> +
> +               uart2: serial@...0000000400 {
> +                       compatible = "cavium,octeon-3860-uart","ns16550";
> +                       reg = <0x11800 0x00000400 0x0 0x400>;
> +                       clock-frequency = <0>;
> +                       current-speed = <115200>;
> +                       reg-shift = <3>;
> +                       interrupts = <1 16>;
> +               };
> +
> +               bootbus: bootbus@...0000000000 {
> +                       compatible = "cavium,octeon-3860-bootbus";
> +                       reg = <0x11800 0x00000000 0x0 0x200>;
> +                       /* The chip select number and offset */
> +                       #address-cells = <2>;
> +                       /* The size of the chip select region */
> +                       #size-cells = <1>;
> +                       ranges = <0 0  0x0 0x1f400000  0xc00000>,
> +                                <1 0  0x10000 0x30000000  0>,
> +                                <2 0  0x10000 0x40000000  0>,
> +                                <3 0  0x10000 0x50000000  0>,
> +                                <4 0  0x0 0x1d020000  0x10000>,
> +                                <5 0  0x0 0x1d040000  0x10000>,
> +                                <6 0  0x0 0x1d050000  0x10000>,
> +                                <7 0  0x10000 0x90000000  0>;
> +
> +                       t-adr    = <20 0 0 0 320   5   5 0>;
> +                       t-ce     = <60 0 0 0 320 300 300 0>;
> +                       t-oe     = <60 0 0 0 320 125 270 0>;
> +                       t-we     = <45 0 0 0 320 150 150 0>;
> +                       t-rd-hld = <35 0 0 0 320 100 100 0>;
> +                       t-wr-hld = <45 0 0 0 320  30  70 0>;
> +                       t-pause  = < 0 0 0 0 320   0   0 0>;
> +                       t-wait   = < 0 0 0 0 320  30   0 0>;
> +                       t-page   = <35 0 0 0 320 320 320 0>;
> +                       t-rd-dly = < 0 0 0 0   0   0   0 0>;
> +
> +                       pages     = <0 0 0 0 0  0  0 0>;
> +                       wait-mode = <0 0 0 0 0  1  0 0>;
> +                       page-mode = <0 0 0 0 0  0  0 0>;
> +                       bus-width = <8 8 8 8 8 16 16 8>;
> +                       ale-mode  = <0 0 0 0 0  0  0 0>;
> +                       sam-mode  = <0 0 0 0 0  0  0 0>;
> +
> +                       flash0: nor@0,0 {
> +                               compatible = "cfi-flash";
> +                               reg = <0 0 0x800000>;
> +                               #address-cells = <1>;
> +                               #size-cells = <1>;
> +                       };
> +
> +                       compact-flash@5,0 {
> +                               compatible = "cavium,ebt3000-compact-flash";
> +                               reg = <5 0 0x10000>, <6 0 0x10000>;
> +                               bus-width = <16>;
> +                               true-ide = <1>;
> +                               dma-engine-handle = <&dma0>;
> +                       };
> +               };
> +
> +               dma0: dma-engine@...0000000100 {
> +                       compatible = "cavium,octeon-5750-bootbus-dma";
> +                       reg = <0x11800 0x00000100 0x0 0x8>;
> +                       interrupts = <0 63>;
> +               };
> +               dma1: dma-engine@...0000000108 {
> +                       compatible = "cavium,octeon-5750-bootbus-dma";
> +                       reg = <0x11800 0x00000108 0x0 0x8>;
> +                       interrupts = <0 63>;
> +               };
> +
> +               uctl: uctl@...006f000000 {
> +                       compatible = "cavium,octeon-6335-uctl";
> +                       reg = <0x11800 0x6f000000 0x0 0x100>;
> +                       ranges; /* Direct mapping */
> +                       #address-cells = <2>;
> +                       #size-cells = <2>;
> +                       /* 12MHz, 24MHz and 48MHz allowed */
> +                       refclk-frequency = <24000000>;
> +                       /* Either "crystal" or "external" */
> +                       refclk-type = "crystal";
> +
> +                       ehci@...0000000000 {
> +                               compatible = "cavium,octeon-6335-ehci","usb-ehci";
> +                               reg = <0x16f00 0x00000000 0x0 0x100>;
> +                               interrupts = <0 56>;
> +                               big-endian-regs;
> +                       };
> +                       ohci@...0000000400 {
> +                               compatible = "cavium,octeon-6335-ohci","usb-ohci";
> +                               reg = <0x16f00 0x00000400 0x0 0x100>;
> +                               interrupts = <0 56>;
> +                               big-endian-regs;
> +                       };
> +               };
> +       };
> +
> +       aliases {
> +               mix0 = &mix0;
> +               mix1 = &mix1;
> +               pip = &pip;
> +               smi0 = &smi0;
> +               smi1 = &smi1;
> +               twsi0 = &twsi0;
> +               twsi1 = &twsi1;
> +               uart0 = &uart0;
> +               uart1 = &uart1;
> +               uart2 = &uart2;
> +               flash0 = &flash0;
> +       };
> + };
> --
> 1.7.2.3
>
>



-- 
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists