| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Tue, 24 Jan 2012 11:18:34 +0100
From: Linus Walleij <linus.walleij@...ricsson.com>
To: Samuel Ortiz <sameo@...ux.intel.com>,
<linux-kernel@...r.kernel.org>
Cc: Viresh Kumar <viresh.kumar@...com>,
Michel Jaouen <michel.jaouen@...ricsson.com>,
Chris Blair <chris.blair@...ricsson.com>,
Linus Walleij <linus.walleij@...aro.org>
Subject: [PATCH] mfd/stmpe: Add support for no-interrupt config
From: Chris Blair <chris.blair@...ricsson.com>
Adds support for boards which have an STMPE device without the
interrupt pin connected.
Cc: Viresh Kumar <viresh.kumar@...com>
Signed-off-by: Chris Blair <chris.blair@...ricsson.com>
Tested-by: Michel Jaouen <michel.jaouen@...ricsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@...ricsson.com>
Signed-off-by: Linus Walleij <linus.walleij@...aro.org>
---
drivers/mfd/stmpe.c | 72 +++++++++++++++++++++++++--------------------
include/linux/mfd/stmpe.h | 2 +
2 files changed, 42 insertions(+), 32 deletions(-)
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index e07947e..7c98e61 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -864,7 +864,7 @@ static int __devinit stmpe_chip_init(struct stmpe *stmpe)
unsigned int irq_trigger = stmpe->pdata->irq_trigger;
int autosleep_timeout = stmpe->pdata->autosleep_timeout;
struct stmpe_variant_info *variant = stmpe->variant;
- u8 icr;
+ u8 icr = 0;
unsigned int id;
u8 data[2];
int ret;
@@ -887,31 +887,33 @@ static int __devinit stmpe_chip_init(struct stmpe *stmpe)
if (ret)
return ret;
- if (id == STMPE801_ID)
- icr = STMPE801_REG_SYS_CTRL_INT_EN;
- else
- icr = STMPE_ICR_LSB_GIM;
-
- /* STMPE801 doesn't support Edge interrupts */
- if (id != STMPE801_ID) {
- if (irq_trigger == IRQF_TRIGGER_FALLING ||
- irq_trigger == IRQF_TRIGGER_RISING)
- icr |= STMPE_ICR_LSB_EDGE;
- }
-
- if (irq_trigger == IRQF_TRIGGER_RISING ||
- irq_trigger == IRQF_TRIGGER_HIGH) {
+ if (!stmpe->pdata->no_irq) {
if (id == STMPE801_ID)
- icr |= STMPE801_REG_SYS_CTRL_INT_HI;
+ icr = STMPE801_REG_SYS_CTRL_INT_EN;
else
- icr |= STMPE_ICR_LSB_HIGH;
- }
+ icr = STMPE_ICR_LSB_GIM;
- if (stmpe->pdata->irq_invert_polarity) {
- if (id == STMPE801_ID)
- icr ^= STMPE801_REG_SYS_CTRL_INT_HI;
- else
- icr ^= STMPE_ICR_LSB_HIGH;
+ /* STMPE801 doesn't support Edge interrupts */
+ if (id != STMPE801_ID) {
+ if (irq_trigger == IRQF_TRIGGER_FALLING ||
+ irq_trigger == IRQF_TRIGGER_RISING)
+ icr |= STMPE_ICR_LSB_EDGE;
+ }
+
+ if (irq_trigger == IRQF_TRIGGER_RISING ||
+ irq_trigger == IRQF_TRIGGER_HIGH) {
+ if (id == STMPE801_ID)
+ icr |= STMPE801_REG_SYS_CTRL_INT_HI;
+ else
+ icr |= STMPE_ICR_LSB_HIGH;
+ }
+
+ if (stmpe->pdata->irq_invert_polarity) {
+ if (id == STMPE801_ID)
+ icr ^= STMPE801_REG_SYS_CTRL_INT_HI;
+ else
+ icr ^= STMPE_ICR_LSB_HIGH;
+ }
}
if (stmpe->pdata->autosleep) {
@@ -988,7 +990,7 @@ int __devinit stmpe_probe(struct stmpe_client_info *ci, int partnum)
if (ci->init)
ci->init(stmpe);
- if (pdata->irq_over_gpio) {
+ if (!pdata->no_irq && pdata->irq_over_gpio) {
ret = gpio_request_one(pdata->irq_gpio, GPIOF_DIR_IN, "stmpe");
if (ret) {
dev_err(stmpe->dev, "failed to request IRQ GPIO: %d\n",
@@ -1005,15 +1007,21 @@ int __devinit stmpe_probe(struct stmpe_client_info *ci, int partnum)
if (ret)
goto free_gpio;
- ret = stmpe_irq_init(stmpe);
- if (ret)
- goto free_gpio;
+ if (pdata->no_irq) {
+ dev_info(stmpe->dev,
+ "board config says IRQs are not supported\n");
+ } else {
+ ret = stmpe_irq_init(stmpe);
+ if (ret)
+ goto free_gpio;
- ret = request_threaded_irq(stmpe->irq, NULL, stmpe_irq,
- pdata->irq_trigger | IRQF_ONESHOT, "stmpe", stmpe);
- if (ret) {
- dev_err(stmpe->dev, "failed to request IRQ: %d\n", ret);
- goto out_removeirq;
+ ret = request_threaded_irq(stmpe->irq, NULL, stmpe_irq,
+ pdata->irq_trigger | IRQF_ONESHOT,
+ "stmpe", stmpe);
+ if (ret) {
+ dev_err(stmpe->dev, "failed to request IRQ: %d\n", ret);
+ goto out_removeirq;
+ }
}
ret = stmpe_devices_init(stmpe);
diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
index ca1d7a3..c4b45fd 100644
--- a/include/linux/mfd/stmpe.h
+++ b/include/linux/mfd/stmpe.h
@@ -188,6 +188,7 @@ struct stmpe_ts_platform_data {
* @irq_invert_polarity: IRQ line is connected with reversed polarity
* @autosleep: bool to enable/disable stmpe autosleep
* @autosleep_timeout: inactivity timeout in milliseconds for autosleep
+ * @no_irq: IRQs are not supported on this board
* @irq_base: base IRQ number. %STMPE_NR_IRQS irqs will be used, or
* %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used.
* @irq_over_gpio: true if gpio is used to get irq
@@ -200,6 +201,7 @@ struct stmpe_ts_platform_data {
struct stmpe_platform_data {
int id;
unsigned int blocks;
+ bool no_irq;
int irq_base;
unsigned int irq_trigger;
bool irq_invert_polarity;
--
1.7.8
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists