| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Mon, 05 May 2014 13:15:33 +0200
From: Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>
To: Eduardo Valentin <eduardo.valentin@...com>
Cc: Zhang Rui <rui.zhang@...el.com>,
Amit Daniel Kachhap <amit.daniel@...sung.com>,
Tomasz Figa <t.figa@...sung.com>,
"Rafael J. Wysocki" <rjw@...ysocki.net>,
Kyungmin Park <kyungmin.park@...sung.com>,
linux-samsung-soc@...r.kernel.org, linux-pm@...r.kernel.org,
linux-kernel@...r.kernel.org, b.zolnierkie@...sung.com
Subject: [PATCH 04/10] thermal: exynos: remove dead code for
TYPE_TWO_POINT_TRIMMING calibration
Only TYPE_ONE_POINT_TRIMMING calibration is used so remove
the dead code for TYPE_TWO_POINT_TRIMMING calibration.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>
---
drivers/thermal/samsung/exynos_tmu.c | 55 ++++++-------------------------
drivers/thermal/samsung/exynos_tmu.h | 20 +----------
drivers/thermal/samsung/exynos_tmu_data.c | 17 +---------
drivers/thermal/samsung/exynos_tmu_data.h | 2 --
4 files changed, 12 insertions(+), 82 deletions(-)
diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index 9f2a5ee..903566f 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -47,8 +47,7 @@
* @irq_work: pointer to the irq work structure.
* @lock: lock to implement synchronization.
* @clk: pointer to the clock structure.
- * @temp_error1: fused value of the first point trim.
- * @temp_error2: fused value of the second point trim.
+ * @temp_error: fused value of the first point trim.
* @regulator: pointer to the TMU regulator structure.
* @reg_conf: pointer to structure to register with core thermal.
*/
@@ -62,14 +61,13 @@ struct exynos_tmu_data {
struct work_struct irq_work;
struct mutex lock;
struct clk *clk;
- u8 temp_error1, temp_error2;
+ u8 temp_error;
struct regulator *regulator;
struct thermal_sensor_conf *reg_conf;
};
/*
* TMU treats temperature as a mapped temperature code.
- * The temperature is converted differently depending on the calibration type.
*/
static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
{
@@ -83,20 +81,7 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
goto out;
}
- switch (pdata->cal_type) {
- case TYPE_TWO_POINT_TRIMMING:
- temp_code = (temp - pdata->first_point_trim) *
- (data->temp_error2 - data->temp_error1) /
- (pdata->second_point_trim - pdata->first_point_trim) +
- data->temp_error1;
- break;
- case TYPE_ONE_POINT_TRIMMING:
- temp_code = temp + data->temp_error1 - pdata->first_point_trim;
- break;
- default:
- temp_code = temp + pdata->default_temp_offset;
- break;
- }
+ temp_code = temp + data->temp_error - pdata->first_point_trim;
out:
return temp_code;
}
@@ -117,20 +102,7 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
goto out;
}
- switch (pdata->cal_type) {
- case TYPE_TWO_POINT_TRIMMING:
- temp = (temp_code - data->temp_error1) *
- (pdata->second_point_trim - pdata->first_point_trim) /
- (data->temp_error2 - data->temp_error1) +
- pdata->first_point_trim;
- break;
- case TYPE_ONE_POINT_TRIMMING:
- temp = temp_code - data->temp_error1 + pdata->first_point_trim;
- break;
- default:
- temp = temp_code - pdata->default_temp_offset;
- break;
- }
+ temp = temp_code - data->temp_error + pdata->first_point_trim;
out:
return temp;
}
@@ -179,19 +151,12 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
} else {
trim_info = readl(data->base + reg->triminfo_data);
}
- data->temp_error1 = trim_info & EXYNOS_TMU_TEMP_MASK;
- data->temp_error2 = ((trim_info >> reg->triminfo_85_shift) &
- EXYNOS_TMU_TEMP_MASK);
-
- if (!data->temp_error1 ||
- (pdata->min_efuse_value > data->temp_error1) ||
- (data->temp_error1 > pdata->max_efuse_value))
- data->temp_error1 = pdata->efuse_value & EXYNOS_TMU_TEMP_MASK;
-
- if (!data->temp_error2)
- data->temp_error2 =
- (pdata->efuse_value >> reg->triminfo_85_shift) &
- EXYNOS_TMU_TEMP_MASK;
+ data->temp_error = trim_info & EXYNOS_TMU_TEMP_MASK;
+
+ if (!data->temp_error ||
+ pdata->min_efuse_value > data->temp_error ||
+ data->temp_error > pdata->max_efuse_value)
+ data->temp_error = pdata->efuse_value & EXYNOS_TMU_TEMP_MASK;
if (pdata->max_trigger_level > MAX_THRESHOLD_LEVS) {
dev_err(&pdev->dev, "Invalid max trigger level\n");
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index e417af8..186e39e 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -26,14 +26,6 @@
#include "exynos_thermal_common.h"
-enum calibration_type {
- TYPE_ONE_POINT_TRIMMING,
- TYPE_ONE_POINT_TRIMMING_25,
- TYPE_ONE_POINT_TRIMMING_85,
- TYPE_TWO_POINT_TRIMMING,
- TYPE_NONE,
-};
-
enum soc_type {
SOC_ARCH_EXYNOS4210 = 1,
SOC_ARCH_EXYNOS4412,
@@ -74,8 +66,6 @@ enum soc_type {
* bitfields. The register validity, offsets and bitfield values may vary
* slightly across different exynos SOC's.
* @triminfo_data: register containing 2 pont trimming data
- * @triminfo_25_shift: shift bit of the 25 C trim value in triminfo_data reg.
- * @triminfo_85_shift: shift bit of the 85 C trim value in triminfo_data reg.
* @triminfo_ctrl: trim info controller register.
* @tmu_ctrl: TMU main controller register.
* @test_mux_addr_shift: shift bits of test mux address.
@@ -116,8 +106,6 @@ enum soc_type {
*/
struct exynos_tmu_registers {
u32 triminfo_data;
- u32 triminfo_25_shift;
- u32 triminfo_85_shift;
u32 triminfo_ctrl;
@@ -207,10 +195,7 @@ struct exynos_tmu_registers {
* @min_efuse_value: minimum valid trimming data
* @max_efuse_value: maximum valid trimming data
* @first_point_trim: temp value of the first point trimming
- * @second_point_trim: temp value of the second point trimming
- * @default_temp_offset: default temperature offset in case of no trimming
* @test_mux; information if SoC supports test MUX
- * @cal_type: calibration type for temperature
* @freq_clip_table: Table representing frequency reduction percentage.
* @freq_tab_count: Count of the above table as frequency reduction may
* applicable to only some of the trigger levels.
@@ -232,15 +217,12 @@ struct exynos_tmu_platform_data {
u8 reference_voltage;
u8 noise_cancel_mode;
- u32 efuse_value;
+ u8 efuse_value;
u32 min_efuse_value;
u32 max_efuse_value;
u8 first_point_trim;
- u8 second_point_trim;
- u8 default_temp_offset;
u8 test_mux;
- enum calibration_type cal_type;
enum soc_type type;
struct freq_clip_table freq_tab[4];
unsigned int freq_tab_count;
diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c
index 4b992d9..c32d186 100644
--- a/drivers/thermal/samsung/exynos_tmu_data.c
+++ b/drivers/thermal/samsung/exynos_tmu_data.c
@@ -27,8 +27,6 @@
#if defined(CONFIG_CPU_EXYNOS4210)
static const struct exynos_tmu_registers exynos4210_tmu_registers = {
.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
- .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
- .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
@@ -66,12 +64,9 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
.max_trigger_level = 4,
.gain = 15,
.reference_voltage = 7,
- .cal_type = TYPE_ONE_POINT_TRIMMING,
.min_efuse_value = 40,
.max_efuse_value = 100,
.first_point_trim = 25,
- .second_point_trim = 85,
- .default_temp_offset = 50,
.freq_tab[0] = {
.freq_clip_max = 800 * 1000,
.temp_level = 85,
@@ -93,8 +88,6 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
#if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250)
static const struct exynos_tmu_registers exynos4412_tmu_registers = {
.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
- .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
- .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
.triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON,
.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
.test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
@@ -145,13 +138,10 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = {
.gain = 8, \
.reference_voltage = 16, \
.noise_cancel_mode = 4, \
- .cal_type = TYPE_ONE_POINT_TRIMMING, \
.efuse_value = 55, \
.min_efuse_value = 40, \
.max_efuse_value = 100, \
.first_point_trim = 25, \
- .second_point_trim = 85, \
- .default_temp_offset = 50, \
.freq_tab[0] = { \
.freq_clip_max = 1400 * 1000, \
.temp_level = 70, \
@@ -195,8 +185,6 @@ struct exynos_tmu_init_data const exynos5250_default_tmu_data = {
#if defined(CONFIG_SOC_EXYNOS5440)
static const struct exynos_tmu_registers exynos5440_tmu_registers = {
.triminfo_data = EXYNOS5440_TMU_S0_7_TRIM,
- .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
- .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
.tmu_ctrl = EXYNOS5440_TMU_S0_7_CTRL,
.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
@@ -240,13 +228,10 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = {
.gain = 5, \
.reference_voltage = 16, \
.noise_cancel_mode = 4, \
- .cal_type = TYPE_ONE_POINT_TRIMMING, \
- .efuse_value = 0x5b2d, \
+ .efuse_value = 45, \
.min_efuse_value = 16, \
.max_efuse_value = 76, \
.first_point_trim = 25, \
- .second_point_trim = 70, \
- .default_temp_offset = 25, \
.type = SOC_ARCH_EXYNOS5440, \
.registers = &exynos5440_tmu_registers, \
.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \
diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h
index 1fed00d..734d1f9 100644
--- a/drivers/thermal/samsung/exynos_tmu_data.h
+++ b/drivers/thermal/samsung/exynos_tmu_data.h
@@ -51,8 +51,6 @@
#define EXYNOS_THD_TEMP_FALL 0x54
#define EXYNOS_EMUL_CON 0x80
-#define EXYNOS_TRIMINFO_25_SHIFT 0
-#define EXYNOS_TRIMINFO_85_SHIFT 8
#define EXYNOS_TMU_RISE_INT_MASK 0x111
#define EXYNOS_TMU_RISE_INT_SHIFT 0
#define EXYNOS_TMU_FALL_INT_MASK 0x111
--
1.8.2.3
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists