| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 26 Jul 2017 10:14:20 +0800
From: Shawn Guo <shawnguo@...nel.org>
To: Martyn Welch <martyn.welch@...labora.co.uk>
Cc: Sebastian Reichel <sre@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Sascha Hauer <kernel@...gutronix.de>,
Fabio Estevam <fabio.estevam@....com>,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org,
Fabien Lahoudere <fabien.lahoudere@...labora.co.uk>,
Sebastian Reichel <sebastian.reichel@...labora.co.uk>
Subject: Re: [PATCH v5] ARM: dts: imx53: Add GE Healthcare PPD
On Wed, Jul 19, 2017 at 04:02:45PM +0100, Martyn Welch wrote:
> From: Fabien Lahoudere <fabien.lahoudere@...labora.co.uk>
>
> PPD is a product from GE Healthcare to monitor vital biometric signals.
>
> Signed-off-by: Fabien Lahoudere <fabien.lahoudere@...labora.co.uk>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@...labora.co.uk>
> Signed-off-by: Martyn Welch <martyn.welch@...labora.co.uk>
> ---
>
> Changes since PATCHv4: https://patchwork.kernel.org/patch/9834733/
> - actually remove fsl,mode node
> - more IOMUX configuration corrections
> - limit CPU frequency to chip max frequency
> Changes since PATCHv3: https://patchwork.kernel.org/patch/9819017/
> - licensing modified
> - manufacturer changed to GE
> - regulator nodes corrected
> - backlight node corrected
> - flags rather than magic numbers used
> - registers for usbphys added
> - set up IOMUX configuration correctly
> - various whitespace corrections
> - removed unused fsl,mode node
> - missing unit addresses added
> - reordered nodes and properties as requested
> Changes since PATCHv2: https://patchwork.kernel.org/patch/9809681/
> - drop dma-info property from serial nodes. That property is not
> available in mainline.
> Changes since PATCHv1: https://patchwork.kernel.org/patch/9265391/
> - fixed issues raised by Mark
> - added some missing vendor prefixes
> - dropped anx9804 nodes (no upstream support/binding)
> - use proper chip-select for ecspi1.cs0
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx53-ppd.dts | 1067 +++++++++++++++++++++++++++++++++++++++
> 2 files changed, 1068 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx53-ppd.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4b17f35..7f3dcab 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -342,6 +342,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
> imx53-ard.dtb \
> imx53-m53evk.dtb \
> imx53-mba53.dtb \
> + imx53-ppd.dtb \
> imx53-qsb.dtb \
> imx53-qsrb.dtb \
> imx53-smd.dtb \
> diff --git a/arch/arm/boot/dts/imx53-ppd.dts b/arch/arm/boot/dts/imx53-ppd.dts
> new file mode 100644
> index 0000000..320026a
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx53-ppd.dts
> @@ -0,0 +1,1067 @@
> +/*
> + * Copyright 2014 General Electric Company
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx53.dtsi"
> +
> +/ {
> + model = "Freescale i.MX53 CPUV0 PPD rev6";
This is a board from GE instead of Freescale, right?
> + compatible = "ge,imx53-cpuvo", "fsl,imx53";
> +
> + aliases {
> + spi0 = &cspi;
> + spi1 = &ecspi1;
> + spi2 = &ecspi2;
> + };
> +
> + chosen {
> + stdout-path = "&uart1:115200n8";
> + };
> +
> + memory@...00000 {
> + device_type = "memory";
> + reg = <0x70000000 0x20000000>,
> + <0xb0000000 0x20000000>;
> + };
> +
> + cko2_11M: sgtl_clock_cko2 {
We prefer to use hyphen than underscore in node name.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <11289600>;
> + };
> +
> + sgtlsound: sound {
> + compatible = "fsl,imx53-cpuvo-sgtl5000",
> + "fsl,imx-audio-sgtl5000";
> + model = "imx53-cpuvo-sgtl5000";
> + ssi-controller = <&ssi2>;
> + audio-codec = <&sgtl5000>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + mux-int-port = <2>;
> + mux-ext-port = <6>;
> + status = "okay";
The "okay" status is not necessary here. We usually use it to toggle
devices that we set "disabled" in <soc>.dtsi.
> + };
> +
> + reg_sgtl5k: regulator-sgtl5k {
> + compatible = "regulator-fixed";
> + regulator-name = "regulator-sgtl5k";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: regulator-usb-otg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usbotg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-0 = <&pinctrl_usb_otg_vbus>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb_vbus: regulator-usb-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usbh1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_usbh2_vbus: regulator-usbh2-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usbh2_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh2_vbus>;
> + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usbh3_vbus: regulator-usbh3-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usbh3_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh3_vbus>;
> + gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + backlight: pwm-bl {
The node name should be generic, so it might be better to switch the
node and label name.
pwm-bl: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 50000>;
> + brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35 \
Why is the backslash is necessary here?
> + 38 40 43 45 48 51 53 56 58 61 63 66 68 71 \
> + 73 76 79 81 84 86 89 91 94 96 99 102 104 \
> + 107 109 112 114 117 119 122 124 127 130 \
> + 132 135 137 140 142 145 147 150 153 155 \
> + 158 160 163 165 168 170 173 175 178 181 \
> + 183 186 188 191 193 196 198 201 204 206 \
> + 209 211 214 216 219 221 224 226 229 232 \
> + 234 237 239 242 244 247 249 252 255>;
> + default-brightness-level = <0>;
> + enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
> + };
> +
> + leds {
> + compatible = "pwm-leds";
> +
> + alarm-brightness {
> + pwms = <&pwm1 0 100000>;
> + max-brightness = <255>;
> + };
> + };
> +
> + gpio-poweroff {
> + compatible = "gpio-poweroff";
> + gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>;
> + };
> +
> + gpio-restart {
> + compatible = "gpio-restart";
> + gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> + active-delay = <100>;
> + inactive-delay = <10>;
> + wait-delay = <100>;
> + };
> +
> + power-gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + power-button {
> + label = "Power button";
> + gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
> + linux,code = <116>;
Can we use the defines in include/dt-bindings/input/linux-event-codes.h
to make it more readable?
> + };
> + };
> +
> + touch-lock-key {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + touch-lock-button {
> + label = "Touch lock button";
> + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
> + linux,code = <88>;
Ditto
> + };
> + };
> +
> + usbphy2: usbphy@2 {
> + reg = <2>;
The @unit-address and 'reg' property should apply to the node which has
a parent node with #address-cells and #size-cells. That said, 'reg'
property should be dropped and a unique node name like usbphy2 should be
good. BTW, why the numbering of phy starts from 2?
> + compatible = "usb-nop-xceiv";
> + reset-gpios = <&gpio4 4 GPIO_ACTIVE_LOW>;
> + clock-names = "main_clk";
> +
Unnecessary newline.
> + clock-frequency = <24000000>;
> + clocks = <&clks IMX5_CLK_CKO2>;
> + assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks IMX5_CLK_OSC>;
> + assigned-clock-parents = <&clks IMX5_CLK_OSC>;
> + status = "okay";
Unnecessary okay status.
> + };
> +
> + usbphy3: usbphy@3 {
> + reg = <3>;
> + compatible = "usb-nop-xceiv";
> + reset-gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
> + clock-names = "main_clk";
> +
> + clock-frequency = <24000000>;
> + clocks = <&clks IMX5_CLK_CKO2>;
> + assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks IMX5_CLK_OSC>;
> + assigned-clock-parents = <&clks IMX5_CLK_OSC>;
> + status = "okay";
> + };
> +
> + panel-lvds0 {
> + compatible = "nvd,9128";
> +
> + port {
> + panel_in_lvds0: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +};
> +
> +&cpu0 {
> + operating-points = <
> + /* kHz uV */
> + 166666 850000
> + 400000 900000
> + 800000 1050000
> + 1000000 1200000
> + >;
Can we have a comment for why we need to overwrite the setting in
imx53.dtsi?
> +};
> +
> +&ecspi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + fsl,spi-num-chipselects = <4>;
The property is obsolete.
> + cs-gpios = <&gpio5 17 GPIO_ACTIVE_LOW
> + &gpio4 10 GPIO_ACTIVE_LOW
> + &gpio4 11 GPIO_ACTIVE_LOW
> + &gpio4 12 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + spidev0: spi@0 {
> + compatible = "ge,achc";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + status = "okay";
Unnecessary okay status.
> + };
> +
> + spidev1: spi@1 {
> + compatible = "ge,achc";
Undocumented compatible.
> + reg = <1>;
> + spi-max-frequency = <1000000>;
> + status = "okay";
> + };
> +
> + gpioxra0: gpio@2 {
> + compatible = "exar,xra1403";
> + reg = <2>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + spi-max-frequency = <1000000>;
> + status = "okay";
> + };
> +
> + gpioxra1: gpio@3 {
> + compatible = "exar,xra1403";
> + reg = <3>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + spi-max-frequency = <1000000>;
> + status = "okay";
> + };
> +};
> +
> +&ecspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + fsl,spi-num-chipselects = <1>;
> + num-chipselects = <1>;
How is num-chipselects used by ecspi driver?
> + cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + da9053@0 {
> + compatible = "dlg,da9053-aa";
> + reg = <0>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <12 0x8>;
> + spi-max-frequency = <1000000>;
> + status = "okay";
Unnecessary okay status.
> +
> + regulators {
> + buck1_reg: buck1 {
> + regulator-name = "BUCKCORE";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <2075000>;
> + regulator-always-on;
> + };
> +
> + buck2_reg: buck2 {
> + regulator-name = "BUCKPRO";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <2075000>;
> + regulator-always-on;
> + };
> +
> + buck3_reg: buck3 {
> + regulator-name = "BUCKMEM";
> + regulator-min-microvolt = <925000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + buck4_reg: buck4 {
> + regulator-name = "BUCKPERI";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-always-on;
> + };
> +
> + ldo1_reg: ldo1 {
> + regulator-name = "ldo1_1v3";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: ldo2 {
> + regulator-name = "ldo2_1v3";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: ldo3 {
> + regulator-name = "ldo3_3v3";
> + regulator-min-microvolt = <1725000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + ldo4_reg: ldo4 {
> + regulator-name = "ldo4_2v775";
> + regulator-min-microvolt = <1725000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + ldo5_reg: ldo5 {
> + regulator-name = "ldo5_3v3";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-always-on;
> + };
> +
> + ldo6_reg: ldo6 {
> + regulator-name = "ldo6_1v3";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-always-on;
> + };
> +
> + ldo7_reg: ldo7 {
> + regulator-name = "ldo7_2v75";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-always-on;
> + };
> +
> + ldo8_reg: ldo8 {
> + regulator-name = "ldo8_1v8";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-always-on;
> + };
> +
> + ldo9_reg: ldo9 {
> + regulator-name = "ldo9_1v5";
> + regulator-min-microvolt = <1250000>;
> + regulator-max-microvolt = <3650000>;
> + regulator-always-on;
> + };
> +
> + ldo10_reg: ldo10 {
> + regulator-name = "ldo10_1v3";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-always-on;
> + };
> + };
> + };
> +
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + status = "disabled";
Why do we need a disabled esdhc1 node here?
> +};
> +
> +&esdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc3>;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-mode = "rmii";
> + phy-reset-gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + sda-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
> + scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + i2xmux_pca: i2c-mux_pca954x@70 {
Drop the _pca954x from node name. And the i2x in the label name looks
odd. I'm actually unsure why you need a label here.
> + compatible = "nxp,pca9547";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reset-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
> +
> + i2c4: i2cmux-ppd@0 {
What does 'ppd' in the node name mean? I would prefer to just name the
node i2c like what the example in bindings/i2c/i2c-mux-pca954x.txt does.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sgtl5000: codec@0a {
Drop the leading zero in unit-address.
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + VDDA-supply = <®_sgtl5k>;
> + VDDIO-supply = <®_sgtl5k>;
> + clocks = <&cko2_11M>;
> + status = "okay";
> + };
> + };
> +
> + i2c5: i2cmux-ppd@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + rtc@30 {
> + compatible = "sii,s35390a";
> + reg = <0x30>;
> + };
> +
> + tmp112@48 {
Can we find a generic name for the node instead of using the hardware
model name.
> + compatible = "ti,tmp112";
Undocumented compatible.
> + reg = <0x48>;
> + };
> +
> + mma8453q@1c {
mma8453q: accelerometer@1c {
> + compatible = "fsl,mma8453";
> + reg = <0x1c>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <6 0>;
> + interrupt-names = "INT1";
> + };
> +
> + mpl3115: mpl3115@60 {
mpl3115: pressure-sensor@60 {
> + compatible = "fsl,mpl3115";
> + reg = <0x60>;
> + };
> +
> + eeprom: eeprom@50 {
> + compatible = "atmel,24c08";
> + reg = <0x50>;
> + };
> + };
> +
> + i2c6: i2cmux-ppd@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c7: i2cmux-ppd@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> +
> + i2c8: i2cmux-ppd@4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <4>;
> + };
> +
> + i2c9: i2cmux-ppd@5 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <5>;
> + };
> +
> + i2c10: i2cmux-ppd@6 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <6>;
> + };
> +
> + i2c11: i2cmux-ppd@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <7>;
> + };
> + };
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + pinctrl-1 = <&pinctrl_i2c2_gpio>;
> + sda-gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
> + scl-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + touchscreen@4b {
> + compatible = "atmel,maxtouch";
> + reg = <0x4b>;
> + interrupt-parent = <&gpio5>;
> + interrupts = <4 0x8>;
> + };
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> + sda-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
> + scl-gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel@0 {
> + status = "okay";
> +
> + port@2 {
> + reg = <2>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in_lvds0>;
> + };
> + };
> + };
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "okay";
> +};
> +
> +&pwm2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm2>;
> + status = "okay";
> +};
> +
> +&ssi2 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + fsl,uart-has-rtscts;
uart-has-rtscts
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&uart5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart5>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + dr_mode = "otg";
> + phy_type = "utmi";
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-0 = <&pinctrl_usb_otg>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_vbus>;
> + phy_type = "utmi";
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbh2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh2>;
> + phy_type = "ulpi";
> + disable-int60ck;
What is this property?
> + dr_mode = "host";
> + fsl,usbphy = <&usbphy2>;
> + vbus-supply = <®_usbh2_vbus>;
> + status = "okay";
> +};
> +
> +&usbh3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh3>;
> + phy_type = "ulpi";
> + disable-int60ck;
> + dr_mode = "host";
> + vbus-supply = <®_usbh3_vbus>;
> + fsl,usbphy = <&usbphy3>;
> + status = "okay";
> +};
> +
> +/* Pin configuration variables */
> +#define NO_PAD_CTL 0x00010000
What does NO_PAD_CTL mean? We should explicitly set pad configuration
in device tree.
> +#define PAD_CTL_DEFAULT 0x00e4
> +#define PAD_CTL_5 0x0005
> +#define PAD_CTL_7 0x0180
I do not see too much point to have these defines.
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog_rev6>;
Have a newline between property list and child node.
> + imx53-cpuvo {
This container node can be dropped.
Shawn
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX53_PAD_DISP0_DAT19__AUDMUX_AUD5_RXD NO_PAD_CTL
> + MX53_PAD_DISP0_DAT17__AUDMUX_AUD5_TXD NO_PAD_CTL
> + MX53_PAD_DISP0_DAT16__AUDMUX_AUD5_TXC NO_PAD_CTL
> + MX53_PAD_DISP0_DAT18__AUDMUX_AUD5_TXFS NO_PAD_CTL
> + MX53_PAD_DI0_PIN15__AUDMUX_AUD6_TXC NO_PAD_CTL
> + MX53_PAD_DI0_PIN3__AUDMUX_AUD6_TXFS NO_PAD_CTL
> + MX53_PAD_DI0_PIN4__AUDMUX_AUD6_RXD NO_PAD_CTL
> + MX53_PAD_DI0_PIN2__AUDMUX_AUD6_TXD NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX53_PAD_DISP0_DAT21__ECSPI1_MOSI NO_PAD_CTL
> + MX53_PAD_DISP0_DAT22__ECSPI1_MISO NO_PAD_CTL
> + MX53_PAD_DISP0_DAT20__ECSPI1_SCLK NO_PAD_CTL
> + /* ECSPI1_SS0, must treat as GPIO for EzPort */
> + MX53_PAD_DISP0_DAT23__GPIO5_17 NO_PAD_CTL
> + MX53_PAD_KEY_COL2__GPIO4_10 NO_PAD_CTL
> + MX53_PAD_KEY_ROW2__GPIO4_11 NO_PAD_CTL
> + MX53_PAD_KEY_COL3__GPIO4_12 NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX53_PAD_EIM_CS1__ECSPI2_MOSI NO_PAD_CTL
> + MX53_PAD_EIM_OE__ECSPI2_MISO NO_PAD_CTL
> + MX53_PAD_EIM_CS0__ECSPI2_SCLK NO_PAD_CTL
> + MX53_PAD_EIM_RW__GPIO2_26 NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
> + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
> + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
> + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
> + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
> + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
> + >;
> + };
> +
> + pinctrl_esdhc3: esdhc3grp {
> + fsl,pins = <
> + MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5
> + MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5
> + MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5
> + MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5
> + MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5
> + MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5
> + MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5
> + MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5
> + MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5
> + MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX53_PAD_FEC_MDC__FEC_MDC NO_PAD_CTL
> + MX53_PAD_FEC_MDIO__FEC_MDIO NO_PAD_CTL
> + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK NO_PAD_CTL
> + MX53_PAD_FEC_RX_ER__FEC_RX_ER NO_PAD_CTL
> + MX53_PAD_FEC_CRS_DV__FEC_RX_DV NO_PAD_CTL
> + MX53_PAD_FEC_RXD1__FEC_RDATA_1 NO_PAD_CTL
> + MX53_PAD_FEC_RXD0__FEC_RDATA_0 NO_PAD_CTL
> + MX53_PAD_FEC_TX_EN__FEC_TX_EN NO_PAD_CTL
> + MX53_PAD_FEC_TXD1__FEC_TDATA_1 NO_PAD_CTL
> + MX53_PAD_FEC_TXD0__FEC_TDATA_0 NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_hog_rev6: hoggrp_rev6 {
> + fsl,pins = <
> + /* CKO2 */
> + MX53_PAD_GPIO_3__CCM_CLKO2 0x0004
> + /* DEFIB_SYNC_MARKER_IN_IRQ */
> + MX53_PAD_GPIO_5__GPIO1_5 NO_PAD_CTL
> + /* ACCELEROMETER_DATA_RDY_N */
> + MX53_PAD_GPIO_6__GPIO1_6 NO_PAD_CTL
> + /* TEMPERATURE_ALERT_N */
> + MX53_PAD_GPIO_7__GPIO1_7 NO_PAD_CTL
> + /* BAROMETRIC_PRESSURE_DATA_RDY_N */
> + MX53_PAD_GPIO_8__GPIO1_8 NO_PAD_CTL
> + /* DOCKING_I2C_INTERFACE_IRQ_N */
> + MX53_PAD_PATA_DATA4__GPIO2_4 NO_PAD_CTL
> + /* PWR_OUT_TO_DOCK_FAULT_N */
> + MX53_PAD_PATA_DATA5__GPIO2_5 NO_PAD_CTL
> + /* ENABLE_PWR_TO_DOCK_N */
> + MX53_PAD_PATA_DATA6__GPIO2_6 NO_PAD_CTL
> + /* HOST_CONTROLLED_RESET_TO_DOCKING_CONNECTOR_N */
> + MX53_PAD_PATA_DATA7__GPIO2_7 NO_PAD_CTL
> + /* REMOTE_ON_REQUEST_FROM_DOCKING_CONNECTOR_IS_ACTIVE_N */
> + MX53_PAD_PATA_DATA12__GPIO2_12 NO_PAD_CTL
> + /* DOCK_PRESENT_N */
> + MX53_PAD_PATA_DATA13__GPIO2_13 NO_PAD_CTL
> + /* ECG_MARKER_IN_FROM_DOCKING_CONNECTOR_IRQ */
> + MX53_PAD_PATA_DATA14__GPIO2_14 NO_PAD_CTL
> + /* ENABLE_ECG_MARKER_INTERFACE_TO_DOCKING_CONNECTOR */
> + MX53_PAD_PATA_DATA15__GPIO2_15 NO_PAD_CTL
> + /* RESET_IMX535_ETHERNET_PHY_N */
> + MX53_PAD_EIM_A22__GPIO2_16 NO_PAD_CTL
> + /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */
> + MX53_PAD_EIM_A21__GPIO2_17 NO_PAD_CTL
> + /* RESET_I2C1_BUS_SEGMENT_MUX_N */
> + MX53_PAD_EIM_A20__GPIO2_18 NO_PAD_CTL
> + /* RESET_IMX535_USB_HOST3_PHY_N */
> + MX53_PAD_EIM_A19__GPIO2_19 NO_PAD_CTL
> + /* ESDHC3_EMMC_NAND_RST_N */
> + MX53_PAD_EIM_A18__GPIO2_20 NO_PAD_CTL
> + /* LCD_AND_UI_INTERFACE_PWR_FAULT_N */
> + MX53_PAD_EIM_A17__GPIO2_21 NO_PAD_CTL
> + /* POWER_DOWN_LVDS0_DESERIALIZER_N */
> + MX53_PAD_EIM_A16__GPIO2_22 NO_PAD_CTL
> + /* POWER_DOWN_LVDS1_DESERIALIZER_N */
> + MX53_PAD_EIM_LBA__GPIO2_27 NO_PAD_CTL
> + /* RESET_DP0_TRANSMITTER_N */
> + MX53_PAD_EIM_EB0__GPIO2_28 NO_PAD_CTL
> + /* RESET_DP1_TRANSMITTER_N */
> + MX53_PAD_EIM_EB1__GPIO2_29 NO_PAD_CTL
> + /* ENABLE_SPDIF_AUDIO_TO_DP0 */
> + MX53_PAD_EIM_DA0__GPIO3_0 NO_PAD_CTL
> + /* ENABLE_SPDIF_AUDIO_TO_DP1 */
> + MX53_PAD_EIM_DA1__GPIO3_1 NO_PAD_CTL
> + /* LVDS1_MUX_CTRL */
> + MX53_PAD_EIM_DA2__GPIO3_2 NO_PAD_CTL
> + /* LVDS0_MUX_CTRL */
> + MX53_PAD_EIM_DA3__GPIO3_3 NO_PAD_CTL
> + /* DP1_TRANSMITTER_IRQ */
> + MX53_PAD_EIM_DA4__GPIO3_4 NO_PAD_CTL
> + /* DP0_TRANSMITTER_IRQ */
> + MX53_PAD_EIM_DA5__GPIO3_5 NO_PAD_CTL
> + /* USB_RESET_N */
> + MX53_PAD_EIM_DA6__GPIO3_6 NO_PAD_CTL
> + /* ENABLE_BATTERY_CHARGER */
> + MX53_PAD_EIM_DA7__GPIO3_7 NO_PAD_CTL
> + /* SOFTWARE_CONTROLLED_PWR_CYCLE */
> + MX53_PAD_EIM_DA8__GPIO3_8 NO_PAD_CTL
> + /* SOFTWARE_CONTROLLED_POWERDOWN */
> + MX53_PAD_EIM_DA9__GPIO3_9 NO_PAD_CTL
> + /* DC_PWR_IN_OK */
> + MX53_PAD_EIM_DA10__GPIO3_10 NO_PAD_CTL
> + /* BATT_PRESENT_N */
> + MX53_PAD_EIM_DA11__GPIO3_11 PAD_CTL_DEFAULT
> + /* PMIC_IRQ_N */
> + MX53_PAD_EIM_DA12__GPIO3_12 NO_PAD_CTL
> + /* PMIC_VDD_FAULT_STATUS_N */
> + MX53_PAD_EIM_DA13__GPIO3_13 NO_PAD_CTL
> + /* IMX535_ETHERNET_PHY_STATUS_IRQ_N */
> + MX53_PAD_EIM_DA14__GPIO3_14 NO_PAD_CTL
> + /* NOT USED - AVAILABLE 3.3V GPIO */
> + MX53_PAD_EIM_DA15__GPIO3_15 NO_PAD_CTL
> + /* NOT USED - AVAILABLE 3.3V GPIO */
> + MX53_PAD_EIM_D22__GPIO3_22 NO_PAD_CTL
> + /* NOT USED - AVAILABLE 3.3V GPIO */
> + MX53_PAD_EIM_D24__GPIO3_24 NO_PAD_CTL
> + /* NBP_PUMP_VALVE_PWR_ENABLE */
> + MX53_PAD_EIM_D25__GPIO3_25 NO_PAD_CTL
> + /* NIBP_RESET_N */
> + MX53_PAD_EIM_D26__GPIO3_26 NO_PAD_CTL
> + /* LATCHED_OVERPRESSURE_N */
> + MX53_PAD_EIM_D27__GPIO3_27 NO_PAD_CTL
> + /* NBP_SBWTCLK */
> + MX53_PAD_EIM_D29__GPIO3_29 NO_PAD_CTL
> + /* ENABLE_WIFI_MODULE */
> + MX53_PAD_GPIO_11__GPIO4_1 NO_PAD_CTL
> + /* WIFI_MODULE_IRQ_N */
> + MX53_PAD_GPIO_12__GPIO4_2 NO_PAD_CTL
> + /* ENABLE_BLUETOOTH_MODULE */
> + MX53_PAD_GPIO_13__GPIO4_3 NO_PAD_CTL
> + /* RESET_IMX535_USB_HOST2_PHY_N */
> + MX53_PAD_GPIO_14__GPIO4_4 NO_PAD_CTL
> + /* ONKEY_IS_DEPRESSED */
> + MX53_PAD_KEY_ROW3__GPIO4_13 NO_PAD_CTL
> + /* UNUSED_GPIO_TO_ALARM_LIGHT_BOARD */
> + MX53_PAD_EIM_WAIT__GPIO5_0 NO_PAD_CTL
> + /* DISPLAY_LOCK_BUTTON_IS_DEPRESSED_N */
> + MX53_PAD_EIM_A25__GPIO5_2 NO_PAD_CTL
> + /* I2C_PCAP_TOUCHSCREEN_IRQ_N */
> + MX53_PAD_EIM_A24__GPIO5_4 NO_PAD_CTL
> + /* NOT USED - AVAILABLE 1.8V GPIO */
> + MX53_PAD_DISP0_DAT13__GPIO5_7 NO_PAD_CTL
> + /* NOT USED - AVAILABLE 1.8V GPIO */
> + MX53_PAD_DISP0_DAT14__GPIO5_8 NO_PAD_CTL
> + /* NOT USED - AVAILABLE 1.8V GPIO */
> + MX53_PAD_DISP0_DAT15__GPIO5_9 NO_PAD_CTL
> + /* HOST_CONTROLLED_RESET_TO_LCD_N */
> + MX53_PAD_CSI0_PIXCLK__GPIO5_18 NO_PAD_CTL
> + /* HOST_CONTROLLED_RESET_TO_PCAP_N */
> + MX53_PAD_CSI0_MCLK__GPIO5_19 NO_PAD_CTL
> + /* LR_SCAN_CTRL */
> + MX53_PAD_CSI0_DATA_EN__GPIO5_20 NO_PAD_CTL
> + /* UD_SCAN_CTRL */
> + MX53_PAD_CSI0_VSYNC__GPIO5_21 NO_PAD_CTL
> + /* DATA_WIDTH_CTRL */
> + MX53_PAD_CSI0_DAT10__GPIO5_28 NO_PAD_CTL
> + /* BACKLIGHT_ENABLE */
> + MX53_PAD_CSI0_DAT11__GPIO5_29 NO_PAD_CTL
> + /* MED_USB_PORT_1_HOST_SELECT */
> + MX53_PAD_EIM_A23__GPIO6_6 NO_PAD_CTL
> + /* MED_USB_PORT_2_HOST_SELECT */
> + MX53_PAD_NANDF_CLE__GPIO6_7 NO_PAD_CTL
> + /* MED_USB_PORT_3_HOST_SELECT */
> + MX53_PAD_NANDF_ALE__GPIO6_8 NO_PAD_CTL
> + /* MED_USB_PORT_4_HOST_SELECT */
> + MX53_PAD_NANDF_WP_B__GPIO6_9 NO_PAD_CTL
> + /* MED_USB_PORT_5_HOST_SELECT */
> + MX53_PAD_NANDF_RB0__GPIO6_10 NO_PAD_CTL
> + /* MED_USB_PORT_6_HOST_SELECT */
> + MX53_PAD_NANDF_CS0__GPIO6_11 NO_PAD_CTL
> + /* MED_USB_PORT_7_HOST_SELECT */
> + MX53_PAD_NANDF_WE_B__GPIO6_12 NO_PAD_CTL
> + /* MED_USB_PORT_8_HOST_SELECT */
> + MX53_PAD_NANDF_RE_B__GPIO6_13 NO_PAD_CTL
> + /* MED_USB_PORT_TO_IMX_SELECT_0 */
> + MX53_PAD_NANDF_CS1__GPIO6_14 NO_PAD_CTL
> + /* MED_USB_PORT_TO_IMX_SELECT_1 */
> + MX53_PAD_NANDF_CS2__GPIO6_15 NO_PAD_CTL
> + /* MED_USB_PORT_TO_IMX_SELECT_2 */
> + MX53_PAD_NANDF_CS3__GPIO6_16 NO_PAD_CTL
> + /* POWER_AND_BOOT_STATUS_INDICATOR */
> + MX53_PAD_PATA_INTRQ__GPIO7_2 NO_PAD_CTL
> + /* ACTIVATE_ALARM_LIGHT_RED */
> + MX53_PAD_PATA_DIOR__GPIO7_3 NO_PAD_CTL
> + /* ACTIVATE_ALARM_LIGHT_YELLOW */
> + MX53_PAD_PATA_DA_1__GPIO7_7 NO_PAD_CTL
> + /* ACTIVATE_ALARM_LIGHT_CYAN */
> + MX53_PAD_PATA_DA_2__GPIO7_8 NO_PAD_CTL
> + /* RUNNING_ON_BATTERY_INDICATOR_GREEN */
> + MX53_PAD_GPIO_16__GPIO7_11 NO_PAD_CTL
> + /* BATTERY_STATUS_INDICATOR_AMBER */
> + MX53_PAD_GPIO_17__GPIO7_12 NO_PAD_CTL
> + /* AUDIO_ALARMS_SILENCED_INDICATOR */
> + MX53_PAD_GPIO_18__GPIO7_13 NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX53_PAD_EIM_D21__I2C1_SCL 0x400001e4
> + MX53_PAD_EIM_D28__I2C1_SDA 0x400001e4
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX53_PAD_EIM_D28__GPIO3_28 0x1e4
> + MX53_PAD_EIM_D21__GPIO3_21 0x1e4
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX53_PAD_EIM_EB2__I2C2_SCL 0x400001e4
> + MX53_PAD_EIM_D16__I2C2_SDA 0x400001e4
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX53_PAD_EIM_D16__GPIO3_16 0x1e4
> + MX53_PAD_EIM_EB2__GPIO2_30 0x1e4
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX53_PAD_EIM_D17__I2C3_SCL 0x400001e4
> + MX53_PAD_EIM_D18__I2C3_SDA 0x400001e4
> + >;
> + };
> +
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX53_PAD_EIM_D18__GPIO3_18 0x1e4
> + MX53_PAD_EIM_D17__GPIO3_17 0x1e4
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX53_PAD_GPIO_9__PWM1_PWMO 0x5
> + >;
> + };
> +
> + pinctrl_pwm2: pwm2grp {
> + fsl,pins = <
> + MX53_PAD_DISP0_DAT9__PWM2_PWMO 0x5
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4
> + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4
> + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4
> + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4
> + MX53_PAD_EIM_D23__UART3_CTS 0x1e4
> + MX53_PAD_EIM_EB3__UART3_RTS 0x1e4
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4
> + MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4
> + >;
> + };
> +
> + pinctrl_uart5: uart5grp {
> + fsl,pins = <
> + MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4
> + MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4
> + >;
> + };
> +
> + pinctrl_usb_otg_vbus: usb-otg-vbusgrp {
> + fsl,pins = <
> + /* USB_HS_OTG_VBUS_ENABLE */
> + MX53_PAD_KEY_ROW4__GPIO4_15 NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_usbh2: usbh2grp {
> + fsl,pins = <
> + /* USB H2 */
> + MX53_PAD_DISP0_DAT0__USBOH3_USBH2_DATA_0 PAD_CTL_7
> + MX53_PAD_DISP0_DAT1__USBOH3_USBH2_DATA_1 PAD_CTL_7
> + MX53_PAD_DISP0_DAT2__USBOH3_USBH2_DATA_2 PAD_CTL_7
> + MX53_PAD_DISP0_DAT3__USBOH3_USBH2_DATA_3 PAD_CTL_7
> + MX53_PAD_DISP0_DAT4__USBOH3_USBH2_DATA_4 PAD_CTL_7
> + MX53_PAD_DISP0_DAT5__USBOH3_USBH2_DATA_5 PAD_CTL_7
> + MX53_PAD_DISP0_DAT6__USBOH3_USBH2_DATA_6 PAD_CTL_7
> + MX53_PAD_DISP0_DAT7__USBOH3_USBH2_DATA_7 PAD_CTL_7
> + MX53_PAD_DISP0_DAT10__USBOH3_USBH2_STP PAD_CTL_7
> + MX53_PAD_DISP0_DAT11__USBOH3_USBH2_NXT PAD_CTL_7
> + MX53_PAD_DISP0_DAT12__USBOH3_USBH2_CLK PAD_CTL_7
> + MX53_PAD_DI0_DISP_CLK__USBOH3_USBH2_DIR PAD_CTL_5
> + MX53_PAD_EIM_D30__USBOH3_USBH2_OC PAD_CTL_7
> + >;
> + };
> +
> + pinctrl_usbh2_vbus: usbh2-vbusgrp {
> + fsl,pins = <
> + /* USB_HS_HOST2_VBUS_ENABLE */
> + MX53_PAD_EIM_D31__GPIO3_31 NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_usbh3_vbus: usbh3-vbusgrp {
> + fsl,pins = <
> + /* USB_HS_HOST3_VBUS_ENABLE */
> + MX53_PAD_CSI0_DAT9__GPIO5_27 NO_PAD_CTL
> + >;
> + };
> +
> + pinctrl_usbh3: usbh3grp {
> + fsl,pins = <
> + /* USB H3 */
> + MX53_PAD_CSI0_DAT12__USBOH3_USBH3_DATA_0 PAD_CTL_7
> + MX53_PAD_CSI0_DAT13__USBOH3_USBH3_DATA_1 PAD_CTL_7
> + MX53_PAD_CSI0_DAT14__USBOH3_USBH3_DATA_2 PAD_CTL_7
> + MX53_PAD_CSI0_DAT15__USBOH3_USBH3_DATA_3 PAD_CTL_7
> + MX53_PAD_CSI0_DAT16__USBOH3_USBH3_DATA_4 PAD_CTL_7
> + MX53_PAD_CSI0_DAT17__USBOH3_USBH3_DATA_5 PAD_CTL_7
> + MX53_PAD_CSI0_DAT18__USBOH3_USBH3_DATA_6 PAD_CTL_7
> + MX53_PAD_CSI0_DAT19__USBOH3_USBH3_DATA_7 PAD_CTL_7
> + MX53_PAD_CSI0_DAT7__USBOH3_USBH3_DIR PAD_CTL_5
> + MX53_PAD_CSI0_DAT6__USBOH3_USBH3_CLK PAD_CTL_7
> + MX53_PAD_CSI0_DAT5__USBOH3_USBH3_NXT PAD_CTL_7
> + MX53_PAD_CSI0_DAT4__USBOH3_USBH3_STP PAD_CTL_7
> + MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC PAD_CTL_7
> + >;
> + };
> +
> + pinctrl_usb_otg: usbotggrp {
> + fsl,pins = <
> + /* USB_OTG_FAULT_N */
> + MX53_PAD_KEY_COL4__USBOH3_USBOTG_OC PAD_CTL_7
> + >;
> + };
> + };
> +};
> --
> 1.8.3.1
>
Powered by blists - more mailing lists