linux-kernel - Re: REGRESSION: HiKey eMMC corruption

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Date:   Mon, 21 May 2018 12:09:34 -0700
From:   John Stultz <john.stultz@...aro.org>
To:     Wei Xu <xuwei5@...ilicon.com>
Cc:     Ryan Grachek <ryan@...ted.us>, Arnd Bergmann <arnd@...db.de>,
        Leo Yan <leo.yan@...aro.org>,
        Guodong Xu <guodong.xu@...aro.org>,
        Ulf Hansson <ulf.hansson@...aro.org>,
        YongQin Liu <yongqin.liu@...aro.org>,
        lkml <linux-kernel@...r.kernel.org>
Subject: Re: REGRESSION: HiKey eMMC corruption

On Mon, May 21, 2018 at 1:34 AM, Wei Xu <xuwei5@...ilicon.com> wrote:
> On 2018/5/18 23:59, John Stultz wrote:
>> The last few months have been busy and I've not been ontop of my
>> upstream testing as well as I'd like, but today I did manage to chase
>> down an issue I've been seeing since 4.17-rc1 on the HiKey board,
>> which was causing emmc corruption and stopping the board from booting.
>>
>> Symptoms usually looked like:
>> [    1.690448] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> ...
>> [    1.777288] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [    1.777760] mmc0: new HS200 MMC card at address 0001
>> ...
>> [   12.214381] dwmmc_k3 f723d000.dwmmc0: Unexpected command timeout, state 3
>> [   12.457420] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> [   12.536676] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [   12.616827] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> [   12.695742] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [   12.772067] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> [   12.850429] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [   12.863384] print_req_error: I/O error, dev mmcblk0, sector 8810504
>> [   12.869778] Aborting journal on device mmcblk0p10-8.
>> [   12.887900] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> [   12.967509] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [   13.130182] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> [   13.209438] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [   13.302085] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> [   13.380462] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [   13.494539] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot
>> req 400000Hz, actual 400000HZ div = 31)
>> [   13.571420] mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot
>> req 150000000Hz, actual 148800000HZ div = 0)
>> [   13.640817] EXT4-fs error (device mmcblk0p10):
>> ext4_journal_check_start:61: Detected aborted journal
>> [   13.650043] EXT4-fs (mmcblk0p10): Remounting filesystem read-only
>>
>> And quite often this would result in a disk that wouldn't properly
>> boot even with older kernels.
>>
>> I've narrowed the issue down to the following change:
>> abd7d0972a192 ("arm64: dts: hikey: Enable HS200 mode on eMMC")
>>
>> Reverting this change seems to make things work reliably for me.
>
> Thanks to report this!
> Let me check with Leo and Guodong to know which property changing
> this is caused by.
>
> Hi Leo and Guodong,
>
> Can you help to confirm the commit abd7d0972a192?
> From the log it seemed to cause by the property "max-frequency".

So yes, I can confirm that if I drop only the max-frequency property
out, keeping the "mmc-hs200-1_8v;" line it still boots for me.

thanks
-john