| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Sat, 17 Nov 2018 05:37:55 -0800
From: Tony Lindgren <tony@...mide.com>
To: Kishon Vijay Abraham I <kishon@...com>
Cc: linux-kernel@...r.kernel.org, linux-usb@...r.kernel.org,
linux-omap@...r.kernel.org, Pavel Machek <pavel@....cz>,
Sebastian Reichel <sre@...nel.org>
Subject: [PATCH 2/2] phy: mapphone-mdm6600: Improve phy related runtime PM calls
I noticed that phy_pm_runtime_get_sync() and phy_pm_runtime_put() are not
currently doing anything for phy-mapphone-mdm6600, only the sysfs interface
for works for "auto" and "on".
This is because of the shared GPIO pins between mdm6600 USB port and n_gsm
port. We have not enabled runtime PM for the phy driver until after we've
booted up mdm6600 properly to the USB mode. Otherwise phy_create() would
have called pm_runtime_enable() and pm_runtime_no_callbacks() automatically
on init.
Let's fix this by registering the phy a bit later after we've powered up the
mdm6600 USB port.
And as the PM runtime support is only needed for the n_gsm mode and not for
USB, we can allow the device to idle between phy_mdm6600_power_on() and
phy_mdm6600_power_off(). Note that for suspend, runtime_pm is already
disabled for the phy so we need to check for phy_pm_runtime_enabled().
Cc: Pavel Machek <pavel@....cz>
Cc: Sebastian Reichel <sre@...nel.org>
Signed-off-by: Tony Lindgren <tony@...mide.com>
---
drivers/phy/motorola/phy-mapphone-mdm6600.c | 71 +++++++++++++++------
1 file changed, 51 insertions(+), 20 deletions(-)
diff --git a/drivers/phy/motorola/phy-mapphone-mdm6600.c b/drivers/phy/motorola/phy-mapphone-mdm6600.c
--- a/drivers/phy/motorola/phy-mapphone-mdm6600.c
+++ b/drivers/phy/motorola/phy-mapphone-mdm6600.c
@@ -16,6 +16,7 @@
#include <linux/gpio/consumer.h>
#include <linux/of_platform.h>
#include <linux/phy/phy.h>
+#include <linux/pinctrl/consumer.h>
#define PHY_MDM6600_PHY_DELAY_MS 4000 /* PHY enable 2.2s to 3.5s */
#define PHY_MDM6600_ENABLED_DELAY_MS 8000 /* 8s more total for MDM6600 */
@@ -124,12 +125,22 @@ static int phy_mdm6600_power_on(struct phy *x)
{
struct phy_mdm6600 *ddata = phy_get_drvdata(x);
struct gpio_desc *enable_gpio = ddata->ctrl_gpios[PHY_MDM6600_ENABLE];
+ int error;
if (!ddata->enabled)
return -ENODEV;
+ error = pinctrl_pm_select_default_state(ddata->dev);
+ if (error)
+ dev_warn(ddata->dev, "%s: error with default_state: %i\n",
+ __func__, error);
+
gpiod_set_value_cansleep(enable_gpio, 1);
+ /* Allow aggressive PM for USB, it's only needed for n_gsm port */
+ if (phy_pm_runtime_enabled(ddata->generic_phy))
+ phy_pm_runtime_put(ddata->generic_phy);
+
return 0;
}
@@ -137,12 +148,26 @@ static int phy_mdm6600_power_off(struct phy *x)
{
struct phy_mdm6600 *ddata = phy_get_drvdata(x);
struct gpio_desc *enable_gpio = ddata->ctrl_gpios[PHY_MDM6600_ENABLE];
+ int error;
if (!ddata->enabled)
return -ENODEV;
+ /* Paired with phy_pm_runtime_put() in phy_mdm6600_power_on() */
+ if (phy_pm_runtime_enabled(ddata->generic_phy)) {
+ error = phy_pm_runtime_get(ddata->generic_phy);
+ if (error < 0 && error != -EINPROGRESS)
+ dev_warn(ddata->dev, "%s: phy_pm_runtime_get: %i\n",
+ __func__, error);
+ }
+
gpiod_set_value_cansleep(enable_gpio, 0);
+ error = pinctrl_pm_select_sleep_state(ddata->dev);
+ if (error)
+ dev_warn(ddata->dev, "%s: error with sleep_state: %i\n",
+ __func__, error);
+
return 0;
}
@@ -555,28 +580,17 @@ static int phy_mdm6600_probe(struct platform_device *pdev)
ddata->dev = &pdev->dev;
platform_set_drvdata(pdev, ddata);
+ /* Active state selected in phy_mdm6600_power_on() */
+ error = pinctrl_pm_select_sleep_state(ddata->dev);
+ if (error)
+ dev_warn(ddata->dev, "%s: error with sleep_state: %i\n",
+ __func__, error);
+
error = phy_mdm6600_init_lines(ddata);
if (error)
return error;
phy_mdm6600_init_irq(ddata);
-
- ddata->generic_phy = devm_phy_create(ddata->dev, NULL, &gpio_usb_ops);
- if (IS_ERR(ddata->generic_phy)) {
- error = PTR_ERR(ddata->generic_phy);
- goto cleanup;
- }
-
- phy_set_drvdata(ddata->generic_phy, ddata);
-
- ddata->phy_provider =
- devm_of_phy_provider_register(ddata->dev,
- of_phy_simple_xlate);
- if (IS_ERR(ddata->phy_provider)) {
- error = PTR_ERR(ddata->phy_provider);
- goto cleanup;
- }
-
schedule_delayed_work(&ddata->bootup_work, 0);
/*
@@ -600,14 +614,31 @@ static int phy_mdm6600_probe(struct platform_device *pdev)
if (error < 0) {
dev_warn(ddata->dev, "failed to wake modem: %i\n", error);
pm_runtime_put_noidle(ddata->dev);
+ goto cleanup;
}
+
+ ddata->generic_phy = devm_phy_create(ddata->dev, NULL, &gpio_usb_ops);
+ if (IS_ERR(ddata->generic_phy)) {
+ error = PTR_ERR(ddata->generic_phy);
+ goto idle;
+ }
+
+ phy_set_drvdata(ddata->generic_phy, ddata);
+
+ ddata->phy_provider =
+ devm_of_phy_provider_register(ddata->dev,
+ of_phy_simple_xlate);
+ if (IS_ERR(ddata->phy_provider))
+ error = PTR_ERR(ddata->phy_provider);
+
+idle:
pm_runtime_mark_last_busy(ddata->dev);
pm_runtime_put_autosuspend(ddata->dev);
- return 0;
-
cleanup:
- phy_mdm6600_device_power_off(ddata);
+ if (error < 0)
+ phy_mdm6600_device_power_off(ddata);
+
return error;
}
--
2.19.1
Powered by blists - more mailing lists