| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Fri, 26 Jul 2019 00:08:49 +0900
From: Chanwoo Choi <cwchoi00@...il.com>
To: Kamil Konieczny <k.konieczny@...tner.samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>,
Marek Szyprowski <m.szyprowski@...sung.com>,
Chanwoo Choi <cw00.choi@...sung.com>,
Krzysztof Kozlowski <krzk@...nel.org>,
Kukjin Kim <kgene@...nel.org>,
Kyungmin Park <kyungmin.park@...sung.com>,
Mark Rutland <mark.rutland@....com>,
MyungJoo Ham <myungjoo.ham@...sung.com>,
Nishanth Menon <nm@...com>, Rob Herring <robh+dt@...nel.org>,
Stephen Boyd <sboyd@...nel.org>,
Viresh Kumar <vireshk@...nel.org>,
devicetree <devicetree@...r.kernel.org>,
linux-arm-kernel <linux-arm-kernel@...ts.infradead.org>,
linux-kernel <linux-kernel@...r.kernel.org>,
Linux PM list <linux-pm@...r.kernel.org>,
linux-samsung-soc <linux-samsung-soc@...r.kernel.org>
Subject: Re: [PATCH v4 2/5] devfreq: exynos-bus: convert to use dev_pm_opp_set_rate()
Hi,
This patch has the same problem as I mentioned on v3.
We need to discuss it on v3[1]. Please check my reply.
[1] [PATCH v3 3/5] devfreq: exynos-bus: convert to use dev_pm_opp_set_rate()
2019년 7월 25일 (목) 오후 11:46, <k.konieczny@...tner.samsung.com>님이 작성:
>
> Reuse opp core code for setting bus clock and voltage. As a side
> effect this allow usage of coupled regulators feature (required
> for boards using Exynos5422/5800 SoCs) because dev_pm_opp_set_rate()
> uses regulator_set_voltage_triplet() for setting regulator voltage
> while the old code used regulator_set_voltage_tol() with fixed
> tolerance. This patch also removes no longer needed parsing of DT
> property "exynos,voltage-tolerance" (no Exynos devfreq DT node uses
> it).
>
> Signed-off-by: Kamil Konieczny <k.konieczny@...tner.samsung.com>
> ---
> Changes:
> v4:
> - remove unrelated changes, add newline before comment
>
> ---
> drivers/devfreq/exynos-bus.c | 108 +++++++++--------------------------
> 1 file changed, 28 insertions(+), 80 deletions(-)
>
> diff --git a/drivers/devfreq/exynos-bus.c b/drivers/devfreq/exynos-bus.c
> index f34fa26f00d0..ebb8f46312b6 100644
> --- a/drivers/devfreq/exynos-bus.c
> +++ b/drivers/devfreq/exynos-bus.c
> @@ -25,7 +25,6 @@
> #include <linux/slab.h>
>
> #define DEFAULT_SATURATION_RATIO 40
> -#define DEFAULT_VOLTAGE_TOLERANCE 2
>
> struct exynos_bus {
> struct device *dev;
> @@ -37,9 +36,8 @@ struct exynos_bus {
>
> unsigned long curr_freq;
>
> - struct regulator *regulator;
> + struct opp_table *opp_table;
> struct clk *clk;
> - unsigned int voltage_tolerance;
> unsigned int ratio;
> };
>
> @@ -99,56 +97,23 @@ static int exynos_bus_target(struct device *dev, unsigned long *freq, u32 flags)
> {
> struct exynos_bus *bus = dev_get_drvdata(dev);
> struct dev_pm_opp *new_opp;
> - unsigned long old_freq, new_freq, new_volt, tol;
> int ret = 0;
>
> - /* Get new opp-bus instance according to new bus clock */
> + /* Get correct frequency for bus. */
> new_opp = devfreq_recommended_opp(dev, freq, flags);
> if (IS_ERR(new_opp)) {
> dev_err(dev, "failed to get recommended opp instance\n");
> return PTR_ERR(new_opp);
> }
>
> - new_freq = dev_pm_opp_get_freq(new_opp);
> - new_volt = dev_pm_opp_get_voltage(new_opp);
> dev_pm_opp_put(new_opp);
>
> - old_freq = bus->curr_freq;
> -
> - if (old_freq == new_freq)
> - return 0;
> - tol = new_volt * bus->voltage_tolerance / 100;
> -
> /* Change voltage and frequency according to new OPP level */
> mutex_lock(&bus->lock);
> + ret = dev_pm_opp_set_rate(dev, *freq);
> + if (!ret)
> + bus->curr_freq = *freq;
>
> - if (old_freq < new_freq) {
> - ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol);
> - if (ret < 0) {
> - dev_err(bus->dev, "failed to set voltage\n");
> - goto out;
> - }
> - }
> -
> - ret = clk_set_rate(bus->clk, new_freq);
> - if (ret < 0) {
> - dev_err(dev, "failed to change clock of bus\n");
> - clk_set_rate(bus->clk, old_freq);
> - goto out;
> - }
> -
> - if (old_freq > new_freq) {
> - ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol);
> - if (ret < 0) {
> - dev_err(bus->dev, "failed to set voltage\n");
> - goto out;
> - }
> - }
> - bus->curr_freq = new_freq;
> -
> - dev_dbg(dev, "Set the frequency of bus (%luHz -> %luHz, %luHz)\n",
> - old_freq, new_freq, clk_get_rate(bus->clk));
> -out:
> mutex_unlock(&bus->lock);
>
> return ret;
> @@ -196,8 +161,10 @@ static void exynos_bus_exit(struct device *dev)
>
> dev_pm_opp_of_remove_table(dev);
> clk_disable_unprepare(bus->clk);
> - if (bus->regulator)
> - regulator_disable(bus->regulator);
> + if (bus->opp_table) {
> + dev_pm_opp_put_regulators(bus->opp_table);
> + bus->opp_table = NULL;
> + }
> }
>
> /*
> @@ -208,39 +175,23 @@ static int exynos_bus_passive_target(struct device *dev, unsigned long *freq,
> {
> struct exynos_bus *bus = dev_get_drvdata(dev);
> struct dev_pm_opp *new_opp;
> - unsigned long old_freq, new_freq;
> - int ret = 0;
> + int ret;
>
> - /* Get new opp-bus instance according to new bus clock */
> + /* Get correct frequency for bus. */
> new_opp = devfreq_recommended_opp(dev, freq, flags);
> if (IS_ERR(new_opp)) {
> dev_err(dev, "failed to get recommended opp instance\n");
> return PTR_ERR(new_opp);
> }
>
> - new_freq = dev_pm_opp_get_freq(new_opp);
> dev_pm_opp_put(new_opp);
>
> - old_freq = bus->curr_freq;
> -
> - if (old_freq == new_freq)
> - return 0;
> -
> /* Change the frequency according to new OPP level */
> mutex_lock(&bus->lock);
> + ret = dev_pm_opp_set_rate(dev, *freq);
> + if (!ret)
> + bus->curr_freq = *freq;
>
> - ret = clk_set_rate(bus->clk, new_freq);
> - if (ret < 0) {
> - dev_err(dev, "failed to set the clock of bus\n");
> - goto out;
> - }
> -
> - *freq = new_freq;
> - bus->curr_freq = new_freq;
> -
> - dev_dbg(dev, "Set the frequency of bus (%luHz -> %luHz, %luHz)\n",
> - old_freq, new_freq, clk_get_rate(bus->clk));
> -out:
> mutex_unlock(&bus->lock);
>
> return ret;
> @@ -258,21 +209,19 @@ static int exynos_bus_parent_parse_of(struct device_node *np,
> struct exynos_bus *bus)
> {
> struct device *dev = bus->dev;
> + struct opp_table *opp_table;
> + const char *vdd = "vdd";
> int i, ret, count, size;
>
> - /* Get the regulator to provide each bus with the power */
> - bus->regulator = devm_regulator_get(dev, "vdd");
> - if (IS_ERR(bus->regulator)) {
> - dev_err(dev, "failed to get VDD regulator\n");
> - return PTR_ERR(bus->regulator);
> - }
> -
> - ret = regulator_enable(bus->regulator);
> - if (ret < 0) {
> - dev_err(dev, "failed to enable VDD regulator\n");
> + opp_table = dev_pm_opp_set_regulators(dev, &vdd, 1);
> + if (IS_ERR(opp_table)) {
> + ret = PTR_ERR(opp_table);
> + dev_err(dev, "failed to set regulators %d\n", ret);
> return ret;
> }
>
> + bus->opp_table = opp_table;
> +
> /*
> * Get the devfreq-event devices to get the current utilization of
> * buses. This raw data will be used in devfreq ondemand governor.
> @@ -313,14 +262,11 @@ static int exynos_bus_parent_parse_of(struct device_node *np,
> if (of_property_read_u32(np, "exynos,saturation-ratio", &bus->ratio))
> bus->ratio = DEFAULT_SATURATION_RATIO;
>
> - if (of_property_read_u32(np, "exynos,voltage-tolerance",
> - &bus->voltage_tolerance))
> - bus->voltage_tolerance = DEFAULT_VOLTAGE_TOLERANCE;
> -
> return 0;
>
> err_regulator:
> - regulator_disable(bus->regulator);
> + dev_pm_opp_put_regulators(bus->opp_table);
> + bus->opp_table = NULL;
>
> return ret;
> }
> @@ -511,8 +457,10 @@ static int exynos_bus_probe(struct platform_device *pdev)
> dev_pm_opp_of_remove_table(dev);
> clk_disable_unprepare(bus->clk);
> err_reg:
> - if (!passive)
> - regulator_disable(bus->regulator);
> + if (!passive) {
> + dev_pm_opp_put_regulators(bus->opp_table);
> + bus->opp_table = NULL;
> + }
>
> return ret;
> }
> --
> 2.22.0
>
--
Best Regards,
Chanwoo Choi
Powered by blists - more mailing lists