| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Thu, 19 Dec 2019 21:20:44 +0100
From: Stephan Gerhold <stephan@...hold.net>
To: Linus Walleij <linus.walleij@...aro.org>
Cc: linux-arm-kernel@...ts.infradead.org,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
Stephan Gerhold <stephan@...hold.net>
Subject: [PATCH 1/9] ARM: dts: ux500: Remove unused ste-href-ab8505.dtsi
The pin configuration for HREF boards with AB8505 was added in
commit 77ad9dfc2c7e ("ARM: ux500: move last AB8505 set-up to DT").
As the commit message notes, it was unused back then and it has
remained so even today, especially considering AB8505 did not have
proper device tree support until recently.
We are now preparing to add support for some Samsung smartphones
that are using AB8505. However, they use different pin configs
because using ste-href-ab8505.dtsi is known to break UART.
There were not many HREFs with AB8505, so at this point it seems
unlikely that we will ever make use of this include. Remove it.
Signed-off-by: Stephan Gerhold <stephan@...hold.net>
---
arch/arm/boot/dts/ste-href-ab8505.dtsi | 234 -------------------------
1 file changed, 234 deletions(-)
delete mode 100644 arch/arm/boot/dts/ste-href-ab8505.dtsi
diff --git a/arch/arm/boot/dts/ste-href-ab8505.dtsi b/arch/arm/boot/dts/ste-href-ab8505.dtsi
deleted file mode 100644
index 95cf38a008e9..000000000000
--- a/arch/arm/boot/dts/ste-href-ab8505.dtsi
+++ /dev/null
@@ -1,234 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2014 Linaro Ltd.
- */
-
-/ {
- soc {
- prcmu@...57000 {
- ab8505 {
- ab8505-gpio {
- /* Hog a few default settings */
- pinctrl-names = "default";
- pinctrl-0 = <&gpio2_default_mode>,
- <&gpio10_default_mode>,
- <&gpio11_default_mode>,
- <&gpio13_default_mode>,
- <&gpio34_default_mode>,
- <&gpio50_default_mode>,
- <&pwm_default_mode>,
- <&adi2_default_mode>,
- <&modsclsda_default_mode>,
- <&resethw_default_mode>,
- <&service_default_mode>;
-
- /*
- * Pins 2, 10, 11, 13, 34 and 50
- * are muxed in as GPIO, and configured as INPUT PULL DOWN
- */
- gpio2 {
- gpio2_default_mode: gpio2_default {
- default_mux {
- function = "gpio";
- groups = "gpio2_a_1";
- };
- default_cfg {
- pins = "GPIO2_R5";
- input-enable;
- bias-pull-down;
- };
- };
- };
- gpio10 {
- gpio10_default_mode: gpio10_default {
- default_mux {
- function = "gpio";
- groups = "gpio10_d_1";
- };
- default_cfg {
- pins = "GPIO10_B16";
- input-enable;
- bias-pull-down;
- };
- };
- };
- gpio11 {
- gpio11_default_mode: gpio11_default {
- default_mux {
- function = "gpio";
- groups = "gpio11_d_1";
- };
- default_cfg {
- pins = "GPIO11_B17";
- input-enable;
- bias-pull-down;
- };
- };
- };
- gpio13 {
- gpio13_default_mode: gpio13_default {
- default_mux {
- function = "gpio";
- groups = "gpio13_d_1";
- };
- default_cfg {
- pins = "GPIO13_D17";
- input-enable;
- bias-disable;
- };
- };
- };
- gpio34 {
- gpio34_default_mode: gpio34_default {
- default_mux {
- function = "gpio";
- groups = "gpio34_a_1";
- };
- default_cfg {
- pins = "GPIO34_H14";
- input-enable;
- bias-pull-down;
- };
- };
- };
- gpio50 {
- gpio50_default_mode: gpio50_default {
- default_mux {
- function = "gpio";
- groups = "gpio50_d_1";
- };
- default_cfg {
- pins = "GPIO50_L4";
- input-enable;
- bias-disable;
- };
- };
- };
- /* This sets up the PWM pin 14 */
- pwm {
- pwm_default_mode: pwm_default {
- default_mux {
- function = "pwmout";
- groups = "pwmout1_d_1";
- };
- default_cfg {
- pins = "GPIO14_C16";
- input-enable;
- bias-pull-down;
- };
- };
- };
- /* This sets up audio interface 2 */
- adi2 {
- adi2_default_mode: adi2_default {
- default_mux {
- function = "adi2";
- groups = "adi2_d_1";
- };
- default_cfg {
- pins = "GPIO17_P2",
- "GPIO18_N3",
- "GPIO19_T1",
- "GPIO20_P3";
- input-enable;
- bias-pull-down;
- };
- };
- };
- /* Modem I2C setup (SCL and SDA pins) */
- modsclsda {
- modsclsda_default_mode: modsclsda_default {
- default_mux {
- function = "modsclsda";
- groups = "modsclsda_d_1";
- };
- default_cfg {
- pins = "GPIO40_J15",
- "GPIO41_J14";
- input-enable;
- bias-pull-down;
- };
- };
- };
- resethw {
- resethw_default_mode: resethw_default {
- default_mux {
- function = "resethw";
- groups = "resethw_d_1";
- };
- default_cfg {
- pins = "GPIO52_D16";
- input-enable;
- bias-pull-down;
- };
- };
- };
- service {
- service_default_mode: service_default {
- default_mux {
- function = "service";
- groups = "service_d_1";
- };
- default_cfg {
- pins = "GPIO53_D15";
- input-enable;
- bias-pull-down;
- };
- };
- };
- /*
- * Clock output pins associated with regulators.
- */
- sysclkreq2 {
- sysclkreq2_default_mode: sysclkreq2_default {
- default_mux {
- function = "sysclkreq";
- groups = "sysclkreq2_d_1";
- };
- default_cfg {
- pins = "GPIO1_N4";
- input-enable;
- bias-disable;
- };
- };
- sysclkreq2_sleep_mode: sysclkreq2_sleep {
- default_mux {
- function = "gpio";
- groups = "gpio1_a_1";
- };
- default_cfg {
- pins = "GPIO1_N4";
- input-enable;
- bias-pull-down;
- };
- };
- };
- sysclkreq4 {
- sysclkreq4_default_mode: sysclkreq4_default {
- default_mux {
- function = "sysclkreq";
- groups = "sysclkreq4_d_1";
- };
- default_cfg {
- pins = "GPIO3_P5";
- input-enable;
- bias-disable;
- };
- };
- sysclkreq4_sleep_mode: sysclkreq4_sleep {
- default_mux {
- function = "gpio";
- groups = "gpio3_a_1";
- };
- default_cfg {
- pins = "GPIO3_P5";
- input-enable;
- bias-pull-down;
- };
- };
- };
- };
- };
- };
- };
-};
--
2.24.1
Powered by blists - more mailing lists