lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date:   Thu, 19 Dec 2019 11:51:30 +0100
From:   Marek Szyprowski <m.szyprowski@...sung.com>
To:     linux-samsung-soc@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-pm@...r.kernel.org
Cc:     Marek Szyprowski <m.szyprowski@...sung.com>,
        Krzysztof Kozlowski <krzk@...nel.org>,
        Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>,
        Kamil Konieczny <k.konieczny@...sung.com>,
        Chanwoo Choi <cw00.choi@...sung.com>
Subject: [PATCH v2 2/2] ARM: dts: exynos: Adjust bus related OPPs to the
 values correct for Odroids

Hardkernel's Odroid XU3/XU4/HC1 boards use bootloader, which configures top
PLLs to the following values: MPLL: 532MHz, CPLL: 666MHz and DPLL: 600MHz.

Adjust all bus related OPPs to the values that are possible to derive from
the top PLL configured by the bootloader. Also add a comment for each bus
describing which PLL is used for it.

The most significant change is the highest rate for wcore bus. It has been
increased to 532MHz as this is the value configured initially by the
bootloader. Also the voltage for this OPP is changed to match the value
set by the bootloader.

This patch finally allows the buses to operate on the rates matching the
values set for each OPP and fixes the following warnings observed on boot:

exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz)
...
exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34)
exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34)
exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34)

The problem with setting incorrect (in some cases much lower) clock rate
for the defined OPP were there from the beginning, but went unnoticed
because the only way to observe it was to manually check the rate of the
respective clocks. The commit 4294a779bd8d ("PM / devfreq: exynos-bus:
Convert to use dev_pm_opp_set_rate()") finally revealed it, because it
enabled use of the generic code from the OPP framework, which issues the
above mentioned warnings.

Signed-off-by: Marek Szyprowski <m.szyprowski@...sung.com>
Tested-by: Chanwoo Choi <cw00.choi@...sung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@...sung.com>
---
 arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 76 +++++++++++--------
 1 file changed, 45 insertions(+), 31 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
index 5fb771680e98..5cf1aed20490 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@@ -38,82 +38,86 @@
 	bus_wcore_opp_table: opp_table2 {
 		compatible = "operating-points-v2";
 
+		/* derived from 532MHz MPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <84000000>;
+			opp-hz = /bits/ 64 <88700000>;
 			opp-microvolt = <925000 925000 1400000>;
 		};
 		opp01 {
-			opp-hz = /bits/ 64 <111000000>;
+			opp-hz = /bits/ 64 <133000000>;
 			opp-microvolt = <950000 950000 1400000>;
 		};
 		opp02 {
-			opp-hz = /bits/ 64 <222000000>;
+			opp-hz = /bits/ 64 <177400000>;
 			opp-microvolt = <950000 950000 1400000>;
 		};
 		opp03 {
-			opp-hz = /bits/ 64 <333000000>;
+			opp-hz = /bits/ 64 <266000000>;
 			opp-microvolt = <950000 950000 1400000>;
 		};
 		opp04 {
-			opp-hz = /bits/ 64 <400000000>;
-			opp-microvolt = <987500 987500 1400000>;
+			opp-hz = /bits/ 64 <532000000>;
+			opp-microvolt = <1000000 1000000 1400000>;
 		};
 	};
 
 	bus_noc_opp_table: opp_table3 {
 		compatible = "operating-points-v2";
 
+		/* derived from 666MHz CPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <67000000>;
+			opp-hz = /bits/ 64 <66600000>;
 		};
 		opp01 {
-			opp-hz = /bits/ 64 <75000000>;
+			opp-hz = /bits/ 64 <74000000>;
 		};
 		opp02 {
-			opp-hz = /bits/ 64 <86000000>;
+			opp-hz = /bits/ 64 <83250000>;
 		};
 		opp03 {
-			opp-hz = /bits/ 64 <100000000>;
+			opp-hz = /bits/ 64 <111000000>;
 		};
 	};
 
 	bus_fsys_apb_opp_table: opp_table4 {
 		compatible = "operating-points-v2";
-		opp-shared;
 
+		/* derived from 666MHz CPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <100000000>;
+			opp-hz = /bits/ 64 <111000000>;
 		};
 		opp01 {
-			opp-hz = /bits/ 64 <200000000>;
+			opp-hz = /bits/ 64 <222000000>;
 		};
 	};
 
 	bus_fsys2_opp_table: opp_table5 {
 		compatible = "operating-points-v2";
 
+		/* derived from 600MHz DPLL */
 		opp00 {
 			opp-hz = /bits/ 64 <75000000>;
 		};
 		opp01 {
-			opp-hz = /bits/ 64 <100000000>;
+			opp-hz = /bits/ 64 <120000000>;
 		};
 		opp02 {
-			opp-hz = /bits/ 64 <150000000>;
+			opp-hz = /bits/ 64 <200000000>;
 		};
 	};
 
 	bus_mfc_opp_table: opp_table6 {
 		compatible = "operating-points-v2";
 
+		/* derived from 666MHz CPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <96000000>;
+			opp-hz = /bits/ 64 <83250000>;
 		};
 		opp01 {
 			opp-hz = /bits/ 64 <111000000>;
 		};
 		opp02 {
-			opp-hz = /bits/ 64 <167000000>;
+			opp-hz = /bits/ 64 <166500000>;
 		};
 		opp03 {
 			opp-hz = /bits/ 64 <222000000>;
@@ -126,8 +130,9 @@
 	bus_gen_opp_table: opp_table7 {
 		compatible = "operating-points-v2";
 
+		/* derived from 532MHz MPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <89000000>;
+			opp-hz = /bits/ 64 <88700000>;
 		};
 		opp01 {
 			opp-hz = /bits/ 64 <133000000>;
@@ -136,32 +141,34 @@
 			opp-hz = /bits/ 64 <178000000>;
 		};
 		opp03 {
-			opp-hz = /bits/ 64 <267000000>;
+			opp-hz = /bits/ 64 <266000000>;
 		};
 	};
 
 	bus_peri_opp_table: opp_table8 {
 		compatible = "operating-points-v2";
 
+		/* derived from 666MHz CPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <67000000>;
+			opp-hz = /bits/ 64 <66600000>;
 		};
 	};
 
 	bus_g2d_opp_table: opp_table9 {
 		compatible = "operating-points-v2";
 
+		/* derived from 666MHz CPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <84000000>;
+			opp-hz = /bits/ 64 <83250000>;
 		};
 		opp01 {
-			opp-hz = /bits/ 64 <167000000>;
+			opp-hz = /bits/ 64 <111000000>;
 		};
 		opp02 {
-			opp-hz = /bits/ 64 <222000000>;
+			opp-hz = /bits/ 64 <166500000>;
 		};
 		opp03 {
-			opp-hz = /bits/ 64 <300000000>;
+			opp-hz = /bits/ 64 <222000000>;
 		};
 		opp04 {
 			opp-hz = /bits/ 64 <333000000>;
@@ -171,8 +178,9 @@
 	bus_g2d_acp_opp_table: opp_table10 {
 		compatible = "operating-points-v2";
 
+		/* derived from 532MHz MPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <67000000>;
+			opp-hz = /bits/ 64 <66500000>;
 		};
 		opp01 {
 			opp-hz = /bits/ 64 <133000000>;
@@ -181,13 +189,14 @@
 			opp-hz = /bits/ 64 <178000000>;
 		};
 		opp03 {
-			opp-hz = /bits/ 64 <267000000>;
+			opp-hz = /bits/ 64 <266000000>;
 		};
 	};
 
 	bus_jpeg_opp_table: opp_table11 {
 		compatible = "operating-points-v2";
 
+		/* derived from 600MHz DPLL */
 		opp00 {
 			opp-hz = /bits/ 64 <75000000>;
 		};
@@ -205,23 +214,25 @@
 	bus_jpeg_apb_opp_table: opp_table12 {
 		compatible = "operating-points-v2";
 
+		/* derived from 666MHz CPLL */
 		opp00 {
-			opp-hz = /bits/ 64 <84000000>;
+			opp-hz = /bits/ 64 <83250000>;
 		};
 		opp01 {
 			opp-hz = /bits/ 64 <111000000>;
 		};
 		opp02 {
-			opp-hz = /bits/ 64 <134000000>;
+			opp-hz = /bits/ 64 <133000000>;
 		};
 		opp03 {
-			opp-hz = /bits/ 64 <167000000>;
+			opp-hz = /bits/ 64 <166500000>;
 		};
 	};
 
 	bus_disp1_fimd_opp_table: opp_table13 {
 		compatible = "operating-points-v2";
 
+		/* derived from 600MHz DPLL */
 		opp00 {
 			opp-hz = /bits/ 64 <120000000>;
 		};
@@ -233,6 +244,7 @@
 	bus_disp1_opp_table: opp_table14 {
 		compatible = "operating-points-v2";
 
+		/* derived from 600MHz DPLL */
 		opp00 {
 			opp-hz = /bits/ 64 <120000000>;
 		};
@@ -247,6 +259,7 @@
 	bus_gscl_opp_table: opp_table15 {
 		compatible = "operating-points-v2";
 
+		/* derived from 600MHz DPLL */
 		opp00 {
 			opp-hz = /bits/ 64 <150000000>;
 		};
@@ -261,6 +274,7 @@
 	bus_mscl_opp_table: opp_table16 {
 		compatible = "operating-points-v2";
 
+		/* derived from 666MHz CPLL */
 		opp00 {
 			opp-hz = /bits/ 64 <84000000>;
 		};
@@ -274,7 +288,7 @@
 			opp-hz = /bits/ 64 <333000000>;
 		};
 		opp04 {
-			opp-hz = /bits/ 64 <400000000>;
+			opp-hz = /bits/ 64 <666000000>;
 		};
 	};
 
@@ -398,7 +412,7 @@
 };
 
 &bus_fsys {
-	operating-points-v2 = <&bus_fsys_apb_opp_table>;
+	operating-points-v2 = <&bus_fsys2_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
-- 
2.17.1

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ