rting at 30000000 (gap: 20000000:c0000000) Built 1 zonelists. Total pages: 113491 Kernel command line: ro root=301 vga=791 video=vesafb:ywrap,mtrr,1024x768-32@60 splash=silent,fadein,theme:eluxrl BOOT_MSG=\"\" CONSOLE=/dev/tty4 console=/dev/tty4 ether=0,0,0,eth0 parport=auto idebus=66 ramdisk_size=10240 ip=dhcp irqpoll ide_setup: idebus=66 Misrouted IRQ fixup and polling support enabled This may significantly impact system performance mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 1000.081 MHz processor. Console: colour dummy device 80x25 Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 30 ... MAX_LOCKDEP_KEYS: 2048 ... CLASSHASH_SIZE: 1024 ... MAX_LOCKDEP_ENTRIES: 8192 ... MAX_LOCKDEP_CHAINS: 16384 ... CHAINHASH_SIZE: 8192 memory used by lock dependency info: 992 kB per task-struct memory footprint: 1200 bytes Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 446632k/457536k available (2665k kernel code, 10356k reserved, 1201k data, 204k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB) lowmem : 0xc0000000 - 0xdbed0000 ( 446 MB) .init : 0xc04ca000 - 0xc04fd000 ( 204 kB) .data : 0xc039a501 - 0xc04c6aa4 (1201 kB) .text : 0xc0100000 - 0xc039a501 (2665 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2075.18 BogoMIPS (lpj=3457902) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 00000019 Compat vDSO mapped to ffffe000. CPU: AMD Sempron(tm) Processor 2100+ stepping 02 Checking 'hlt' instruction... OK. ACPI: Core revision 20070126 ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... failed. ...trying to set up timer as Virtual Wire IRQ... works. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on device 00:18 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: Device [FDC] status [00000008]: functional but not present; setting present ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GRFB._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXA._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.LAN_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 7 9 10 11 12 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 7 of bridge 0000:00:06.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:06.0 PCI: Cannot allocate resource region 3 of device 0000:00:00.0 pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:01: iomem range 0xfec00000-0xfecfffff could not be reserved pnp: 00:01: iomem range 0xfed00000-0xfedfffff has been reserved pnp: 00:01: iomem range 0xfee00000-0xfeefffff could not be reserved Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: fc100000-fc2fffff PREFETCH window: f8000000-fbffffff PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:07.0 IO window: a000-afff MEM window: fc300000-fc3fffff PREFETCH window: fc000000-fc0fffff PCI: Bridge: 0000:00:14.4 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:07.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 7, 720896 bytes) TCP bind hash table entries: 16384 (order: 7, 720896 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered Initializing RT-Tester: OK io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered PCI: MSI quirk detected. MSI deactivated. Boot video device is 0000:01:05.0 PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie02] Allocate Port Service[0000:00:06.0:pcie03] PCI: Setting latency timer of device 0000:00:07.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:07.0:pcie00] Allocate Port Service[0000:00:07.0:pcie03] vesafb: framebuffer at 0xf8000000, mapped to 0xdc880000, using 3072k, total 16384k vesafb: mode is 1024x768x16, linelength=2048, pages=9 vesafb: protected mode interface info at c000:9fba vesafb: pmi: set display start = c00ca044, set palette = c00ca102 vesafb: scrolling: ywrap using protected mode interface, yres_virtual=1536 vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device cs5535_gpio: DIVIL not found Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize loop: module loaded Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 Copyright (c) 1999-2006 Intel Corporation. pcnet32.c:v1.33 27.Jun.2006 tsbogend@alpha.franken.de Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 66MHz system bus speed for PIO modes SB600_PATA: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 SB600_PATA: chipset revision 0 SB600_PATA: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... Switched to high resolution mode on CPU 0 hda: FCR512, ATA DISK drive hda: selected mode 0x22 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 128KiB hda: 1025136 sectors (524 MB) w/0KiB Cache, CHS=1017/16/63, DMA hda: hda1 hda2 hda3 ahci 0000:00:12.0: version 2.2 ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17 ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:12.0: flags: ncq ilck pm led clo pmp pio slum part scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 cmd 0xdc80c100 ctl 0x00000000 bmdma 0x00000000 irq 17 ata2: SATA max UDMA/133 cmd 0xdc80c180 ctl 0x00000000 bmdma 0x00000000 irq 17 ata3: SATA max UDMA/133 cmd 0xdc80c200 ctl 0x00000000 bmdma 0x00000000 irq 17 ata4: SATA max UDMA/133 cmd 0xdc80c280 ctl 0x00000000 bmdma 0x00000000 irq 17 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 18 ehci_hcd 0000:00:13.5: EHCI Host Controller ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.5: debug port 1 ehci_hcd 0000:00:13.5: irq 18, io mem 0xfc60a400 ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 16, io mem 0xfc604000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 19, io mem 0xfc605000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-5: new high speed USB device using ehci_hcd and address 2 ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 20 ohci_hcd 0000:00:13.2: OHCI Host Controller ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:13.2: irq 20, io mem 0xfc606000 usb 1-5: configuration #1 chosen from 1 choice usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.3: OHCI Host Controller ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5 ohci_hcd 0000:00:13.3: irq 19, io mem 0xfc607000 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 20 ohci_hcd 0000:00:13.4: OHCI Host Controller ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6 ohci_hcd 0000:00:13.4: irq 20, io mem 0xfc608000 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... scsi4 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 IRQ 0 rejected by it's handlers, but taken by: i8042 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode IRQ 0 rejected by it's handlers, but taken by: i8042 IRQ 0 rejected by it's handlers, but taken by: i8042 input: ImPS/2 Generic Wheel Mouse as /class/input/input1 EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. IRQ 0 rejected by it's handlers, but taken by: ide0 scsi 4:0:0:0: Direct-Access SanDisk Cruzer Micro 0.1 PQ: 0 ANSI: 2 sd 4:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB) IRQ 0 rejected by it's handlers, but taken by: ehci_hcd:usb1 sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 4:0:0:0: [sda] Assuming drive cache: write through sd 4:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB) IRQ 0 rejected by it's handlers, but taken by: ehci_hcd:usb1 sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 4:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 4:0:0:0: [sda] Attached SCSI removable disk sd 4:0:0:0: Attached scsi generic sg0 type 0 usb-storage: device scan complete kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 204k freed Warning: unable to open an initial console. IRQ 0 rejected by it's handlers, but taken by: ide0 IRQ 0 rejected by it's handlers, but taken by: ide0 IRQ 0 rejected by it's handlers, but taken by: ide0 hda: selected mode 0x22 IRQ 0 rejected by it's handlers, but taken by: ide0 hda: selected mode 0x22 IRQ 0 rejected by it's handlers, but taken by: ide0 kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on hda3, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on hda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. IRQ 0 rejected by it's handlers, but taken by: ide0 Real Time Clock Driver v1.12ac r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:08:00.0 to 64 r8169 0000:08:00.0: no MSI. Back to INTx. eth0: RTL8168c/8111c at 0xdc82a000, 00:19:99:0b:9d:5b, XID 3c0000c0 IRQ 18 IRQ 0 rejected by it's handlers, but taken by: ide0 fuse init (API version 7.8) IRQ 0 rejected by it's handlers, but taken by: ehci_hcd:usb1 ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16 hda_codec: Unknown model for ALC262, trying auto-probe from BIOS... input: Power Button (FF) as /class/input/input2 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input3 ACPI: Power Button (CM) [PWRB] No dock devices found. r8169: eth0: link up EXT3 FS on hda1, internal journal kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. EXT3 FS on hda1, internal journal