Date:	Mon, 16 Jan 2012 11:46:20 +0100
From:	Sascha Hauer <s.hauer@...gutronix.de>
To:	Jaccon Bastiaansen <jaccon.bastiaansen@...il.com>
Cc:	kernel@...gutronix.de, u.kleine-koenig@...gutronix.de,
	davem@...emloft.net, cavokz@...il.com,
	linux-arm-kernel@...ts.infradead.org, netdev@...r.kernel.org
Subject: Re: [PATCH V3 1/4] CS89x0 : add platform driver support

On Sat, Jan 14, 2012 at 08:56:36PM +0100, Jaccon Bastiaansen wrote:
> The CS89x0 ethernet controller is used on a number of evaluation
> boards, such as the MX31ADS. The current driver has memory address and
> IRQ settings for each board on which this controller is used. Driver
> updates are therefore required to support other boards that also use
> the CS89x0. To avoid these driver updates, a better mechanism
> (platform driver support) is added to communicate the board dependent
> settings to the driver.
> 
> Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@...il.com>

Looks good to me now.

Reviewed-by: Sascha Hauer <s.hauer@...gutronix.de>


> ---
>  drivers/net/Space.c                  |    2 +
>  drivers/net/ethernet/cirrus/Kconfig  |   19 +++--
>  drivers/net/ethernet/cirrus/cs89x0.c |  123 ++++++++++++++++++++++++++++++++--
>  3 files changed, 129 insertions(+), 15 deletions(-)
> 
> diff --git a/drivers/net/Space.c b/drivers/net/Space.c
> index 068c356..88bbd8f 100644
> --- a/drivers/net/Space.c
> +++ b/drivers/net/Space.c
> @@ -190,8 +190,10 @@ static struct devprobe2 isa_probes[] __initdata = {
>  	{seeq8005_probe, 0},
>  #endif
>  #ifdef CONFIG_CS89x0
> +#ifndef CONFIG_CS89x0_PLATFORM
>   	{cs89x0_probe, 0},
>  #endif
> +#endif
>  #ifdef CONFIG_AT1700
>  	{at1700_probe, 0},
>  #endif
> diff --git a/drivers/net/ethernet/cirrus/Kconfig b/drivers/net/ethernet/cirrus/Kconfig
> index 1f8648f..3784b1b 100644
> --- a/drivers/net/ethernet/cirrus/Kconfig
> +++ b/drivers/net/ethernet/cirrus/Kconfig
> @@ -5,8 +5,7 @@
>  config NET_VENDOR_CIRRUS
>  	bool "Cirrus devices"
>  	default y
> -	depends on ISA || EISA || MACH_IXDP2351 || ARCH_IXDP2X01 \
> -		|| MACH_MX31ADS || MACH_QQ2440 || (ARM && ARCH_EP93XX) || MAC
> +	depends on ISA || EISA || ARM || (ARM && ARCH_EP93XX) || MAC
>  	---help---
>  	  If you have a network (Ethernet) card belonging to this class, say Y
>  	  and read the Ethernet-HOWTO, available from
> @@ -21,8 +20,7 @@ if NET_VENDOR_CIRRUS
>  
>  config CS89x0
>  	tristate "CS89x0 support"
> -	depends on (ISA || EISA || MACH_IXDP2351 \
> -		|| ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440)
> +	depends on ISA || EISA || ARM
>  	---help---
>  	  Support for CS89x0 chipset based Ethernet cards. If you have a
>  	  network (Ethernet) card of this type, say Y and read the
> @@ -33,10 +31,15 @@ config CS89x0
>  	  To compile this driver as a module, choose M here. The module
>  	  will be called cs89x0.
>  
> -config CS89x0_NONISA_IRQ
> -	def_bool y
> -	depends on CS89x0 != n
> -	depends on MACH_IXDP2351 || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440
> +config CS89x0_PLATFORM
> +	bool "CS89x0 platform driver support"
> +	depends on CS89x0
> +	help
> +	  Say Y to compile the cs89x0 driver as a platform driver. This
> +	  makes this driver suitable for use on certain evaluation boards
> +	  such as the iMX21ADS.
> +
> +	  If you are unsure, say N.
>  
>  config EP93XX_ETH
>  	tristate "EP93xx Ethernet support"
> diff --git a/drivers/net/ethernet/cirrus/cs89x0.c b/drivers/net/ethernet/cirrus/cs89x0.c
> index f328da2..aec732c 100644
> --- a/drivers/net/ethernet/cirrus/cs89x0.c
> +++ b/drivers/net/ethernet/cirrus/cs89x0.c
> @@ -100,9 +100,6 @@
>  
>  */
>  
> -/* Always include 'config.h' first in case the user wants to turn on
> -   or override something. */
> -#include <linux/module.h>
>  
>  /*
>   * Set this to zero to disable DMA code
> @@ -131,9 +128,12 @@
>  
>  */
>  
> +#include <linux/module.h>
> +#include <linux/printk.h>
>  #include <linux/errno.h>
>  #include <linux/netdevice.h>
>  #include <linux/etherdevice.h>
> +#include <linux/platform_device.h>
>  #include <linux/kernel.h>
>  #include <linux/types.h>
>  #include <linux/fcntl.h>
> @@ -151,6 +151,7 @@
>  #include <asm/system.h>
>  #include <asm/io.h>
>  #include <asm/irq.h>
> +#include <linux/atomic.h>
>  #if ALLOW_DMA
>  #include <asm/dma.h>
>  #endif
> @@ -174,26 +175,32 @@ static char version[] __initdata =
>     them to system IRQ numbers. This mapping is card specific and is set to
>     the configuration of the Cirrus Eval board for this chip. */
>  #if defined(CONFIG_MACH_IXDP2351)
> +#define CS89x0_NONISA_IRQ
>  static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
>  static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
>  #elif defined(CONFIG_ARCH_IXDP2X01)
> +#define CS89x0_NONISA_IRQ
>  static unsigned int netcard_portlist[] __used __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
>  static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
>  #elif defined(CONFIG_MACH_QQ2440)
> +#define CS89x0_NONISA_IRQ
>  #include <mach/qq2440.h>
>  static unsigned int netcard_portlist[] __used __initdata = { QQ2440_CS8900_VIRT_BASE + 0x300, 0 };
>  static unsigned int cs8900_irq_map[] = { QQ2440_CS8900_IRQ, 0, 0, 0 };
>  #elif defined(CONFIG_MACH_MX31ADS)
> +#define CS89x0_NONISA_IRQ
>  #include <mach/board-mx31ads.h>
>  static unsigned int netcard_portlist[] __used __initdata = {
>  	PBC_BASE_ADDRESS + PBC_CS8900A_IOBASE + 0x300, 0
>  };
>  static unsigned cs8900_irq_map[] = {EXPIO_INT_ENET_INT, 0, 0, 0};
>  #else
> +#ifndef CONFIG_CS89x0_PLATFORM
>  static unsigned int netcard_portlist[] __used __initdata =
>     { 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
>  static unsigned int cs8900_irq_map[] = {10,11,12,5};
>  #endif
> +#endif
>  
>  #if DEBUGGING
>  static unsigned int net_debug = DEBUGGING;
> @@ -236,6 +243,11 @@ struct net_local {
>  	unsigned char *end_dma_buff;	/* points to the end of the buffer */
>  	unsigned char *rx_dma_ptr;	/* points to the next packet  */
>  #endif
> +#ifdef CONFIG_CS89x0_PLATFORM
> +	void *virt_addr;	/* Virtual address for accessing the CS89x0. */
> +	unsigned long phys_addr;/* Physical address for accessing the CS89x0. */
> +	unsigned long size;	/* Length of CS89x0 memory region. */
> +#endif
>  };
>  
>  /* Index to functions, as function prototypes. */
> @@ -294,6 +306,7 @@ static int __init media_fn(char *str)
>  __setup("cs89x0_media=", media_fn);
>  
>  
> +#ifndef CONFIG_CS89x0_PLATFORM
>  /* Check for a network adaptor of this type, and return '0' iff one exists.
>     If dev->base_addr == 0, probe all likely locations.
>     If dev->base_addr == 1, always return failure.
> @@ -343,6 +356,7 @@ out:
>  	return ERR_PTR(err);
>  }
>  #endif
> +#endif
>  
>  #if defined(CONFIG_MACH_IXDP2351)
>  static u16
> @@ -736,8 +750,9 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
>  			dev->irq = i;
>  	} else {
>  		i = lp->isa_config & INT_NO_MASK;
> +#ifndef CONFIG_CS89x0_PLATFORM
>  		if (lp->chip_type == CS8900) {
> -#ifdef CONFIG_CS89x0_NONISA_IRQ
> +#ifdef CS89x0_NONISA_IRQ
>  		        i = cs8900_irq_map[0];
>  #else
>  			/* Translate the IRQ using the IRQ mapping table. */
> @@ -758,6 +773,7 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
>  			}
>  #endif
>  		}
> +#endif
>  		if (!dev->irq)
>  			dev->irq = i;
>  	}
> @@ -1168,6 +1184,7 @@ write_irq(struct net_device *dev, int chip_type, int irq)
>  	int i;
>  
>  	if (chip_type == CS8900) {
> +#ifndef CONFIG_CS89x0_PLATFORM
>  		/* Search the mapping table for the corresponding IRQ pin. */
>  		for (i = 0; i != ARRAY_SIZE(cs8900_irq_map); i++)
>  			if (cs8900_irq_map[i] == irq)
> @@ -1175,6 +1192,10 @@ write_irq(struct net_device *dev, int chip_type, int irq)
>  		/* Not found */
>  		if (i == ARRAY_SIZE(cs8900_irq_map))
>  			i = 3;
> +#else
> +		/* INTRQ0 pin is used for interrupt generation. */
> +		i = 0;
> +#endif
>  		writereg(dev, PP_CS8900_ISAINT, i);
>  	} else {
>  		writereg(dev, PP_CS8920_ISAINT, irq);
> @@ -1228,7 +1249,7 @@ net_open(struct net_device *dev)
>  	}
>  	else
>  	{
> -#ifndef CONFIG_CS89x0_NONISA_IRQ
> +#if !defined(CS89x0_NONISA_IRQ) && !defined(CONFIG_CS89x0_PLATFORM)
>  		if (((1 << dev->irq) & lp->irq_map) == 0) {
>  			printk(KERN_ERR "%s: IRQ %d is not in our map of allowable IRQs, which is %x\n",
>                                 dev->name, dev->irq, lp->irq_map);
> @@ -1746,7 +1767,7 @@ static int set_mac_address(struct net_device *dev, void *p)
>  	return 0;
>  }
>  
> -#ifdef MODULE
> +#if defined(MODULE) && !defined(CONFIG_CS89x0_PLATFORM)
>  
>  static struct net_device *dev_cs89x0;
>  
> @@ -1900,7 +1921,95 @@ cleanup_module(void)
>  	release_region(dev_cs89x0->base_addr, NETCARD_IO_EXTENT);
>  	free_netdev(dev_cs89x0);
>  }
> -#endif /* MODULE */
> +#endif /* MODULE && !CONFIG_CS89x0_PLATFORM */
> +
> +#ifdef CONFIG_CS89x0_PLATFORM
> +static int __init cs89x0_platform_probe(struct platform_device *pdev)
> +{
> +	struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
> +	struct net_local *lp = netdev_priv(dev);
> +	struct resource *mem_res;
> +	int err;
> +
> +	if (!dev)
> +		return -ENODEV;
> +
> +	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	dev->irq = platform_get_irq(pdev, 0);
> +	if (mem_res == NULL || dev->irq <= 0) {
> +		dev_warn(&dev->dev, "memory/interrupt resource missing.\n");
> +		err = -ENOENT;
> +		goto free;
> +	}
> +
> +	lp->phys_addr = mem_res->start;
> +	lp->size = mem_res->end - mem_res->start + 1;
> +	if (!request_mem_region(lp->phys_addr, lp->size, DRV_NAME)) {
> +		dev_warn(&dev->dev, "request_mem_region() failed.\n");
> +		err = -ENOMEM;
> +		goto free;
> +	}
> +
> +	lp->virt_addr = ioremap(lp->phys_addr, lp->size);
> +	if (!lp->virt_addr) {
> +		dev_warn(&dev->dev, "ioremap() failed.\n");
> +		err = -ENOMEM;
> +		goto release;
> +	}
> +
> +	err = cs89x0_probe1(dev, (int)lp->virt_addr, 0);
> +	if (err) {
> +		dev_warn(&dev->dev, "no cs8900 or cs8920 detected.\n");
> +		goto unmap;
> +	}
> +
> +	platform_set_drvdata(pdev, dev);
> +	return 0;
> +
> +unmap:
> +	iounmap(lp->virt_addr);
> +release:
> +	release_mem_region(lp->phys_addr, lp->size);
> +free:
> +	free_netdev(dev);
> +	return err;
> +}
> +
> +static int cs89x0_platform_remove(struct platform_device *pdev)
> +{
> +	struct net_device *dev = platform_get_drvdata(pdev);
> +	struct net_local *lp = netdev_priv(dev);
> +
> +	unregister_netdev(dev);
> +	iounmap(lp->virt_addr);
> +	release_mem_region(lp->phys_addr, lp->size);
> +	free_netdev(dev);
> +	return 0;
> +}
> +
> +static struct platform_driver cs89x0_driver = {
> +	.driver	= {
> +		.name	= DRV_NAME,
> +		.owner	= THIS_MODULE,
> +	},
> +	.remove	= cs89x0_platform_remove,
> +};
> +
> +static int __init cs89x0_init(void)
> +{
> +	return platform_driver_probe(&cs89x0_driver, cs89x0_platform_probe);
> +}
> +
> +module_init(cs89x0_init);
> +
> +static void __exit cs89x0_cleanup(void)
> +{
> +	platform_driver_unregister(&cs89x0_driver);
> +}
> +
> +module_exit(cs89x0_cleanup);
> +
> +#endif /* CONFIG_CS89x0_PLATFORM */
>  
>  /*
>   * Local variables:
> -- 
> 1.7.1
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Powered by blists - more mailing lists