netdev - Re: [PATCH] net: fix e100.rst Documentation build errors

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Date:   Mon, 18 Jun 2018 13:44:38 +0200
From:   Michal Kubecek <mkubecek@...e.cz>
To:     Jani Nikula <jani.nikula@...ux.intel.com>
Cc:     Randy Dunlap <rdunlap@...radead.org>,
        "linux-doc@...r.kernel.org" <linux-doc@...r.kernel.org>,
        "netdev@...r.kernel.org" <netdev@...r.kernel.org>,
        Jeff Kirsher <jeffrey.t.kirsher@...el.com>,
        David Miller <davem@...emloft.net>,
        LKML <linux-kernel@...r.kernel.org>,
        Aaron Brown <aaron.f.brown@...el.com>
Subject: Re: [PATCH] net: fix e100.rst Documentation build errors

On Mon, Jun 18, 2018 at 11:04:51AM +0300, Jani Nikula wrote:
> On Sat, 16 Jun 2018, Randy Dunlap <rdunlap@...radead.org> wrote:
> > From: Randy Dunlap <rdunlap@...radead.org>
> >
> > Fix Documentation build errors in e100.rst.  Several section titles
> > and the corresponding underlines should not be indented.
> 
> Really the content blocks below the titles should not be indented
> either. It's not an error, but the end result is probably not what you
> want.

Also the indentation of this part:

> Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
>    structure that describes a receive buffer and its attributes to the network
>    controller. The data in the descriptor is used by the controller to write
>    data from the controller to host memory. In the 3.x.x driver the valid range
>    for this parameter is 64-256. The default value is 256. This parameter can be
>    changed using the command::
> 
>    ethtool -G eth? rx n
> 
>    Where n is the number of desired Rx descriptors.
> 
> Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
>    structure that describes a transmit buffer and its attributes to the network
>    controller. The data in the descriptor is used by the controller to read
>    data from the host memory to the controller. In the 3.x.x driver the valid
>    range for this parameter is 64-256. The default value is 128. This parameter
>    can be changed using the command::
> 
>    ethtool -G eth? tx n
> 
>    Where n is the number of desired Tx descriptors.
> 
> Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
>    default. The ethtool utility can be used as follows to force speed/duplex.::
> 
>    ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
> 
>    NOTE: setting the speed/duplex to incorrect values will cause the link to
>    fail.
> 
> Event Log Message Level:  The driver uses the message level flag to log events
>    to syslog. The message level can be set at driver load time. It can also be
>    set using the command::
> 
>    ethtool -s eth? msglvl n

causes

.../Documentation/networking/e100.rst:56: WARNING: Literal block expected; none found.
.../Documentation/networking/e100.rst:67: WARNING: Literal block expected; none found.
.../Documentation/networking/e100.rst:74: WARNING: Literal block expected; none found.
.../Documentation/networking/e100.rst:83: WARNING: Literal block expected; none found.

as the literal block has the same indentation as preceding paragraph
(except for the first line).

Michal Kubecek