lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20190222233744.25735-4-maxime.chevallier@bootlin.com>
Date:   Sat, 23 Feb 2019 00:37:40 +0100
From:   Maxime Chevallier <maxime.chevallier@...tlin.com>
To:     davem@...emloft.net
Cc:     Maxime Chevallier <maxime.chevallier@...tlin.com>,
        netdev@...r.kernel.org, linux-kernel@...r.kernel.org,
        Andrew Lunn <andrew@...n.ch>,
        Florian Fainelli <f.fainelli@...il.com>,
        Heiner Kallweit <hkallweit1@...il.com>,
        Russell King <linux@...linux.org.uk>,
        linux-arm-kernel@...ts.infradead.org,
        Antoine Tenart <antoine.tenart@...tlin.com>,
        thomas.petazzoni@...tlin.com, gregory.clement@...tlin.com,
        miquel.raynal@...tlin.com, nadavh@...vell.com, stefanc@...vell.com,
        mw@...ihalf.com
Subject: [PATCH net-next v2 3/7] net: phy: marvell10g: Use 2500BASEX when using 2.5GBASET

The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.

Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.

At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.

This was tested with :
 - The 88X3310, which is on the MacchiatoBin
 - The 88E2010, an Alaska PHY that has no fiber interfaces, and is
   limited to 5G maximum speed.

Signed-off-by: Maxime Chevallier <maxime.chevallier@...tlin.com>
---
 drivers/net/phy/marvell10g.c | 26 +++++++++++++++++++-------
 1 file changed, 19 insertions(+), 7 deletions(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 821ef1b2f8cc..9342d8c2ff7f 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -235,6 +235,7 @@ static int mv3310_config_init(struct phy_device *phydev)
 {
 	/* Check that the PHY interface type is compatible */
 	if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
+	    phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
 	    phydev->interface != PHY_INTERFACE_MODE_XAUI &&
 	    phydev->interface != PHY_INTERFACE_MODE_RXAUI &&
 	    phydev->interface != PHY_INTERFACE_MODE_10GKR)
@@ -313,18 +314,29 @@ static int mv3310_aneg_done(struct phy_device *phydev)
 static void mv3310_update_interface(struct phy_device *phydev)
 {
 	if ((phydev->interface == PHY_INTERFACE_MODE_SGMII ||
+	     phydev->interface == PHY_INTERFACE_MODE_2500BASEX ||
 	     phydev->interface == PHY_INTERFACE_MODE_10GKR) && phydev->link) {
 		/* The PHY automatically switches its serdes interface (and
-		 * active PHYXS instance) between Cisco SGMII and 10GBase-KR
-		 * modes according to the speed.  Florian suggests setting
-		 * phydev->interface to communicate this to the MAC. Only do
-		 * this if we are already in either SGMII or 10GBase-KR mode.
+		 * active PHYXS instance) between Cisco SGMII, 10GBase-KR and
+		 * 2500BaseX modes according to the speed.  Florian suggests
+		 * setting phydev->interface to communicate this to the MAC.
+		 * Only do this if we are already in one of the above modes.
 		 */
-		if (phydev->speed == SPEED_10000)
+		switch (phydev->speed) {
+		case SPEED_10000:
 			phydev->interface = PHY_INTERFACE_MODE_10GKR;
-		else if (phydev->speed >= SPEED_10 &&
-			 phydev->speed < SPEED_10000)
+			break;
+		case SPEED_2500:
+			phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+			break;
+		case SPEED_1000:
+		case SPEED_100:
+		case SPEED_10:
 			phydev->interface = PHY_INTERFACE_MODE_SGMII;
+			break;
+		default:
+			break;
+		}
 	}
 }
 
-- 
2.19.2

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ