linux-ext4 - Re: CFQ idling kills I/O performance on ext4 with blkio cgroup controller

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Date:   Thu, 30 May 2019 01:38:59 -0700
From:   "Srivatsa S. Bhat" <srivatsa@...il.mit.edu>
To:     Paolo Valente <paolo.valente@...aro.org>
Cc:     linux-fsdevel@...r.kernel.org,
        linux-block <linux-block@...r.kernel.org>,
        linux-ext4@...r.kernel.org, cgroups@...r.kernel.org,
        kernel list <linux-kernel@...r.kernel.org>,
        Jens Axboe <axboe@...nel.dk>, Jan Kara <jack@...e.cz>,
        jmoyer@...hat.com, Theodore Ts'o <tytso@....edu>,
        amakhalov@...are.com, anishs@...are.com, srivatsab@...are.com
Subject: Re: CFQ idling kills I/O performance on ext4 with blkio cgroup
 controller

On 5/23/19 4:32 PM, Srivatsa S. Bhat wrote:
> On 5/22/19 7:30 PM, Srivatsa S. Bhat wrote:
>> On 5/22/19 3:54 AM, Paolo Valente wrote:
>>>
>>>
>>>> Il giorno 22 mag 2019, alle ore 12:01, Srivatsa S. Bhat <srivatsa@...il.mit.edu> ha scritto:
>>>>
>>>> On 5/22/19 2:09 AM, Paolo Valente wrote:
>>>>>
>>>>> First, thank you very much for testing my patches, and, above all, for
>>>>> sharing those huge traces!
>>>>>
>>>>> According to the your traces, the residual 20% lower throughput that you
>>>>> record is due to the fact that the BFQ injection mechanism takes a few
>>>>> hundredths of seconds to stabilize, at the beginning of the workload.
>>>>> During that setup time, the throughput is equal to the dreadful ~60-90 KB/s
>>>>> that you see without this new patch.  After that time, there
>>>>> seems to be no loss according to the trace.
>>>>>
>>>>> The problem is that a loss lasting only a few hundredths of seconds is
>>>>> however not negligible for a write workload that lasts only 3-4
>>>>> seconds.  Could you please try writing a larger file?
>>>>>
>>>>
>>>> I tried running dd for longer (about 100 seconds), but still saw around
>>>> 1.4 MB/s throughput with BFQ, and between 1.5 MB/s - 1.6 MB/s with
>>>> mq-deadline and noop.
>>>
>>> Ok, then now the cause is the periodic reset of the mechanism.
>>>
>>> It would be super easy to fill this gap, by just gearing the mechanism
>>> toward a very aggressive injection.  The problem is maintaining
>>> control.  As you can imagine from the performance gap between CFQ (or
>>> BFQ with malfunctioning injection) and BFQ with this fix, it is very
>>> hard to succeed in maximizing the throughput while at the same time
>>> preserving control on per-group I/O.
>>>
>>
>> Ah, I see. Just to make sure that this fix doesn't overly optimize for
>> total throughput (because of the testcase we've been using) and end up
>> causing regressions in per-group I/O control, I ran a test with
>> multiple simultaneous dd instances, each writing to a different
>> portion of the filesystem (well separated, to induce seeks), and each
>> dd task bound to its own blkio cgroup. I saw similar results with and
>> without this patch, and the throughput was equally distributed among
>> all the dd tasks.
>>
> Actually, it turns out that I ran the dd tasks directly on the block
> device for this experiment, and not on top of ext4. I'll redo this on
> ext4 and report back soon.
> 

With all your patches applied (including waker detection for the low
latency case), I ran four simultaneous dd instances, each writing to a
different ext4 partition, and each dd task bound to its own blkio
cgroup.  The throughput continued to be well distributed among the dd
tasks, as shown below (I increased dd's block size from 512B to 8KB
for these experiments to get double-digit throughput numbers, so as to
make comparisons easier).

bfq with low_latency = 1:

819200000 bytes (819 MB, 781 MiB) copied, 16452.6 s, 49.8 kB/s
819200000 bytes (819 MB, 781 MiB) copied, 17139.6 s, 47.8 kB/s
819200000 bytes (819 MB, 781 MiB) copied, 17251.7 s, 47.5 kB/s
819200000 bytes (819 MB, 781 MiB) copied, 17384 s, 47.1 kB/s

bfq with low_latency = 0:

819200000 bytes (819 MB, 781 MiB) copied, 16257.9 s, 50.4 kB/s
819200000 bytes (819 MB, 781 MiB) copied, 17204.5 s, 47.6 kB/s
819200000 bytes (819 MB, 781 MiB) copied, 17220.6 s, 47.6 kB/s
819200000 bytes (819 MB, 781 MiB) copied, 17348.1 s, 47.2 kB/s
 
Regards,
Srivatsa
VMware Photon OS