[PATCH] Add SATA device to VIA IRQ quirk fixup list

Gentoo users at http://bugs.gentoo.org/138036 reported a 2.6.16.17 regression:
new kernels will not boot their system from their VIA SATA hardware.

The solution is just to add the SATA device to the fixup list.
This should also fix the same problem reported by Scott J. Harmon on LKML.

Signed-off-by: Daniel Drake <dsd@gentoo.org>

Index: linux/drivers/pci/quirks.c
===================================================================
--- linux.orig/drivers/pci/quirks.c
+++ linux/drivers/pci/quirks.c
@@ -648,10 +648,31 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_V
  * Some of the on-chip devices are actually '586 devices' so they are
  * listed here.
  */
+
+static int via_irq_fixup_needed = -1;
+
+/*
+ * As some VIA hardware is available in PCI-card form, we need to restrict
+ * this quirk to VIA PCI hardware built onto VIA-based motherboards only.
+ * This table lists southbridges on motherboards where this quirk needs to
+ * be run.
+ */
+static const struct pci_device_id via_irq_fixup_tbl[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233A) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237) },
+	{ 0, },
+};
+
 static void quirk_via_irq(struct pci_dev *dev)
 {
 	u8 irq, new_irq;
 
+	if (via_irq_fixup_needed == -1)
+		via_irq_fixup_needed = pci_dev_present(via_irq_fixup_tbl);
+
+	if (!via_irq_fixup_needed)
+		return;
+
 	new_irq = dev->irq & 0xf;
 	pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
 	if (new_irq != irq) {
@@ -661,13 +682,7 @@ static void quirk_via_irq(struct pci_dev
 		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
 	}
 }
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_5, quirk_via_irq);
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq);
 
 /*
  * VIA VT82C598 has its device ID settable and many BIOSes