Linux version 2.6.17 (root@localhost) (gcc version 3.2.2 (Mandrake Linux 9.1 3.2.2-3mdk)) #1 Fri Jul 28 15:05:07 AST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000fff0000 (usable) BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS) BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 255MB LOWMEM available. On node 0 totalpages: 65520 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 61424 pages, LIFO batch:15 DMI 2.1 present. ACPI: RSDP (v000 COMPAQ ) @ 0x000f7090 ACPI: RSDT (v001 COMPAQ CPQB0B9 0x00000000 0x00000000) @ 0x0fff3000 ACPI: FADT (v001 COMPAQ CPQB0B9 0x00000000 0x00000000) @ 0x0fff3040 ACPI: DSDT (v001 COMPAQ AWRDACPI 0x00001000 MSFT 0x01000007) @ 0x00000000 Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000) Built 1 zonelists Kernel command line: root=/dev/nfs ip=bootp nfsroot=rh52 lapic BOOT_IMAGE=grub/v617.s2r Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! mapped APIC to ffffd000 (fee00000) Enabling fast FPU save and restore... done. Initializing CPU#0 PID hash table entries: 1024 (order: 10, 4096 bytes) Detected 432.483 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256600k/262080k available (1770k kernel code, 4988k reserved, 560k data, 212k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 865.59 BogoMIPS (lpj=432797) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0183fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 128K CPU: After all inits, caps: 0183fbff 00000000 00000000 00000040 00000000 00000000 00000000 CPU: Intel Celeron (Mendocino) stepping 05 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed ACPI: setting ELCR to 0200 (from 8800) NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb180, last bus=1 Setting up standard PCI resources Nosave address range: 00000000000a0000 - 00000000000f0000 Nosave address range: 00000000000f0000 - 0000000000100000 Nosave address range: 000000000fff0000 - 000000000fff3000 Nosave address range: 000000000fff3000 - 0000000010000000 Nosave address range: 0000000010000000 - 00000000ffff0000 ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region 4000-403f claimed by PIIX4 ACPI PCI quirk: region 5000-500f claimed by PIIX4 SMB ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15) ACPI: Power Resource [PFAN] (on) PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: d000-dfff MEM window: disabled. PREFETCH window: disabled. NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 8192 bind 4096) TCP reno registered io scheduler noop registered (default) Limiting direct PCI/PCI transfers. ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Fan [FAN] (on) ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Thermal Zone [THRM] (38 C) Real Time Clock Driver v1.12ac Linux Tulip driver version 1.1.13 (May 11, 2002) ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 tulip0: EEPROM default media type Autosense. tulip0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip0: MII transceiver #0 config 1000 status 782d advertising 01e1. eth0: Digital DS21140 Tulip rev 34 at 0001e400, 00:80:C8:45:77:A9, IRQ 11. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PCI: Enabling device 0000:00:07.1 (0000 -> 0001) PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later PIIX4: neither IDE port enabled (BIOS) Probing IDE interface ide0... Probing IDE interface ide1... serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ACPI wakeup devices: USB0 ACPI: (supports S0 S1 S3 S4 S5) Sending BOOTP requests . OK IP-Config: Got BOOTP answer from 10.0.0.1, my address is 10.0.0.2 IP-Config: Complete: device=eth0, addr=10.0.0.2, mask=255.0.0.0, gw=10.0.0.1, host=10.0.0.2, domain=intranet, nis-domain=(none), bootserver=10.0.0.1, rootserver=10.0.0.1, rootpath= Looking up port of RPC 100003/2 on 10.0.0.1 Looking up port of RPC 100005/1 on 10.0.0.1 VFS: Mounted root (nfs filesystem) readonly. Freeing unused kernel memory: 212k freed eth0: Setting full-duplex based on MII#0 link partner capability of 05e1.