Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb
Linux version 2.4.21 (andy@MARS-V) (gcc version 3.2.3) #1 Fri Nov 11 14:03:24 CST 2005
Motorola  PMC8241
PORTING  by  Premier Microelectronics Development
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: ethaddr=00:08:54:E1:78:0D

 sizeof(OpenPIC_Reg)=16
OpenPIC Version 1.2 (1 CPUs and 138 IRQ sources) at fc040000
Decrementer frequency = 133.000000 MHz
Warning: real time clock seems stuck!
Calibrating delay loop... 176.94 BogoMIPS
Memory: 61172k available (1704k kernel code, 960k data, 248k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page cache: 64MB memory, maximum pages = 5120, maximum inactive pages = 300
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
NTFS driver v1.1.22 [Flags: R/O]
NH230_gpio: NH200 GPIO setting ...
Trying to free free IRQ20
NH230_gpio: Get the IRQ SUCCESS !!
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xfc004500 (irq = 137) is a ST16650
RTC: character device (/dev/rtc) driver v1.00 (01/22/2005) is registered
PCF8563 Real-Time Clock Driver, $Revision: 1.15 $
PCF8563: RTC Voltage Low - reliable date/time information is no longer guaranteed!
PCF8563: RTC Voltage Low - try to set date/timeto default 2005/01/01 12:00:00
RAMDISK driver initialized: 16 RAM disks of 193840K size 1024 blocksize
loop: loaded (max 8 devices)
RTL8169s/8110s: RTL8169S: NAPI enabled
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169s/8110s Gigabit Ethernet driver 2.2-R5 (09/05/2005) at 0xc5000e00, 00:08:54:e1:78:0d, IRQ 17
eth0: Auto-negotiation Enabled.
eth0: 100Mbps Full-duplex operation.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
IT8211: IDE controller at PCI slot 00:10.0
IT8211: chipset revision 17
IT8211: not 100% native mode: will probe irqs later
IT8212: wait 8 seconds for hard disk ready before initialize IT8212 after cold boot.
........ Done
    ide0: BM-DMA at 0xbffdd0-0xbffdd7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xbffdd8-0xbffddf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG SP1614N, ATA DISK drive
blk: queue c02d3800, I/O limit 4095Mb (mask 0xffffffff)
Probing IDE interface ide1...
ide0 at 0xbffdf8-0xbffdff,0xbffdf6 on irq 18
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 312581808 sectors (160042 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1 p2
SCSI subsystem driver Revision: 1.00
physmap flash device: 400000 at ffc00000
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Using physmap partition definition
Creating 8 MTD partitions on "Physically mapped flash":
0x00300000-0x00320000 : "Boot-loader"
0x00000000-0x00004000 : "Boot CFG"
0x00004000-0x00006000 : "POST Result"
0x00008000-0x00010000 : "Linux CFG"
0x00006000-0x00008000 : "Reserved"
0x00010000-0x00190000 : "Linux"
0x00190000-0x00300000 : "RAM disk #2"
0x00320000-0x00400000 : "RAM disk #1 (root)"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:0e.3: PCI device 17a0:8084
ehci_hcd 00:0e.3: irq 19, pci mem c5004f00
usb.c: new USB bus registered, assigned bus number 1
PCI: 00:0e.3 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:0e.3 PCI cache line size corrected to 32.
ehci_hcd 00:0e.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-uhci.c: $Revision: 1.275 $ time 14:05:35 Nov 11 2005
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: USB UHCI at I/O 0xbfffe0, IRQ 19
host/usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 677k freed
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 248k init
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 538168k swap-space (priority -1)