Linux version 2.6.18-rc6 (root@chevrolet) (gcc version 4.1.2 20060903 (prerelease) (Ubuntu 4.1.1-13ubuntu1)) #1 SMP Wed Sep 6 17:27:24 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fffc000 (usable) BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data) BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 511MB LOWMEM available. found SMP MP-table at 000f5500 On node 0 totalpages: 131068 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 126972 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 ASUS ) @ 0x000f6930 ACPI: RSDT (v001 ASUS CV266DLS 0x30303031 MSFT 0x31313031) @ 0x1fffc000 ACPI: FADT (v001 ASUS CV266DLS 0x30303031 MSFT 0x31313031) @ 0x1fffc100 ACPI: BOOT (v001 ASUS CV266DLS 0x30303031 MSFT 0x31313031) @ 0x1fffc040 ACPI: MADT (v001 ASUS CV266DLS 0x30303031 MSFT 0x31313031) @ 0x1fffc080 ACPI: DSDT (v001 ASUS CV266DLS 0x00001000 MSFT 0x0100000b) @ 0x00000000 ACPI: PM-Timer IO Port: 0xe408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x03] enabled) Processor #3 6:8 APIC version 17 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 17 ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Detected 999.736 MHz processor. Built 1 zonelists. Total pages: 131068 Kernel command line: root=/dev/sda2 ro quiet splash mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 514368k/524272k available (3127k kernel code, 9368k reserved, 1180k data, 200k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2001.80 BogoMIPS (lpj=4003604) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. Freeing SMP alternatives: 20k freed ACPI: Core revision 20060707 CPU0: Intel Pentium III (Coppermine) stepping 0a Booting processor 1/0 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 1999.59 BogoMIPS (lpj=3999183) CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Pentium III (Coppermine) stepping 0a Total of 2 processors activated (4001.39 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=608 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0d40, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Firmware left 0000:00:05.0 e100 interrupts enabled, disabling Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report irda_init() NET: Registered protocol family 23 Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized PCI: Bridge: 0000:00:01.0 IO window: d000-dfff MEM window: de800000-dfdfffff PREFETCH window: e0000000-f7ffffff PCI: Bus 2, cardbus bridge: 0000:00:0f.0 IO window: 00001000-000010ff IO window: 00001400-000014ff PREFETCH window: 30000000-31ffffff MEM window: 32000000-33ffffff PCI: Bus 6, cardbus bridge: 0000:00:0f.1 IO window: 00001800-000018ff IO window: 00001c00-00001cff PREFETCH window: 34000000-35ffffff MEM window: 36000000-37ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:0f.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 16 PCI: Enabling device 0000:00:0f.1 (0000 -> 0003) ACPI: PCI Interrupt 0000:00:0f.1[B] -> GSI 19 (level, low) -> IRQ 17 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered Simple Boot Flag at 0x3a set to 0x1 IA-32 Microcode Update Driver: v1.14a NTFS driver 2.1.27 [Flags: R/O]. SGI XFS with ACLs, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected VIA Pro 266 chipset agpgart: AGP aperture is 64M @ 0xf8000000 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 19 (level, low) -> IRQ 17 e100: eth0: e100_probe: addr 0xde000000, irq 17, MAC addr 00:E0:18:2E:FF:C0 PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered netconsole: not configured, aborting Linux video capture interface: v2.00 saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 19 (level, low) -> IRQ 17 saa7134[0]: found at 0000:00:0c.0, rev: 1, irq: 17, latency: 32, mmio: 0xdc000000 saa7134[0]: subsystem: 153b:1143, board: Terratec Cinergy 600 TV [card=11,autodetected] saa7134[0]: board init: gpio is 50000 input: saa7134 IR (Terratec Cinergy 60 as /class/input/input0 saa7134[0]: i2c eeprom 00: 3b 15 43 11 ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: registered device video0 [v4l2] saa7134[0]: registered device vbi0 saa7134[0]: registered device radio0 tuner 0-0060: All bytes are equal. It is not a TEA5767 tuner 0-0060: chip found @ 0xc0 (saa7134[0]) tuner 0-0060: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1 ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:pio, hdd:DMA Probing IDE interface ide0... hda: ST3200822A, ATA DISK drive hdb: ST3200822A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdd: IOMEGA ZIP 100 ATAPI Floppy, ATAPI FLOPPY drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(33) hda: cache flushes supported hda: hda1 hdb: max request size: 512KiB hdb: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(33) hdb: cache flushes supported hdb: hdb1 ide-floppy driver 0.99.newide hdd: No disk in drive hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 18 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs Vendor: SEAGATE Model: ST318452LW Rev: 0004 Type: Direct-Access ANSI SCSI revision: 03 scsi0:A:0:0: Tagged Queuing enabled. Depth 253 target0:0:0: Beginning Domain Validation target0:0:0: wide asynchronous target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63) target0:0:0: Ending Domain Validation ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 18 (level, low) -> IRQ 16 scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs Vendor: PIONEER Model: DVD-ROM DVD-304F Rev: 1.03 Type: CD-ROM ANSI SCSI revision: 02 target1:0:4: Beginning Domain Validation target1:0:4: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 16) target1:0:4: Domain Validation skipping write tests target1:0:4: Ending Domain Validation Vendor: YAMAHA Model: CRW-F1S Rev: 1.0g Type: CD-ROM ANSI SCSI revision: 02 target1:0:5: Beginning Domain Validation target1:0:5: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) target1:0:5: Domain Validation skipping write tests target1:0:5: Ending Domain Validation Vendor: SEAGATE Model: DAT 04687-XXX Rev: 6610 Type: Sequential-Access ANSI SCSI revision: 02 target1:0:6: Beginning Domain Validation target1:0:6: FAST-10 SCSI 7.8 MB/s ST (128 ns, offset 15) target1:0:6: Domain Validation skipping write tests target1:0:6: Ending Domain Validation st: Version 20050830, fixed bufsize 32768, s/g segs 256 st 1:0:6:0: Attached scsi tape st0 st0: try direct i/o: yes (alignment 512 B) SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB) sda: Write Protect is off sda: Mode Sense: a3 00 10 08 SCSI device sda: drive cache: write back w/ FUA SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB) sda: Write Protect is off sda: Mode Sense: a3 00 10 08 SCSI device sda: drive cache: write back w/ FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda sr0: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:4:0: Attached scsi CD-ROM sr0 sr1: scsi3-mmc drive: 44x/44x writer cd/rw xa/form2 cdda tray sr 1:0:5:0: Attached scsi CD-ROM sr1 sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 1:0:4:0: Attached scsi generic sg1 type 5 sr 1:0:5:0: Attached scsi generic sg2 type 5 st 1:0:6:0: Attached scsi generic sg3 type 1 Yenta: CardBus bridge found at 0000:00:0f.0 [14ef:0220] Yenta: ISA IRQ mask 0x0000, PCI irq 16 Socket status: 30000006 Yenta: CardBus bridge found at 0000:00:0f.1 [14ef:0220] Yenta: ISA IRQ mask 0x0000, PCI irq 17 Socket status: 30000006 usbmon: debugfs is not available USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: VIA IRQ fixup for 0000:00:11.2, from 9 to 11 uhci_hcd 0000:00:11.2: UHCI Host Controller uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:11.2: irq 11, io base 0x00009800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: VIA IRQ fixup for 0000:00:11.3, from 9 to 11 uhci_hcd 0000:00:11.3: UHCI Host Controller uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:11.3: irq 11, io base 0x00009400 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:11.4[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: VIA IRQ fixup for 0000:00:11.4, from 9 to 11 uhci_hcd 0000:00:11.4: UHCI Host Controller uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:11.4: irq 11, io base 0x00009000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-1: new full speed USB device using uhci_hcd and address 2 usb 1-1: configuration #1 chosen from 1 choice usb 2-1: new full speed USB device using uhci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice usb 2-2: new full speed USB device using uhci_hcd and address 3 usb 2-2: configuration #1 chosen from 1 choice drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3304 usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device usbcore: registered new driver ftdi_sio drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input1 gameport: EMU10K1 is pci0000:00:0e.1/gameport0, io 0xa400, speed 1193kHz input: AT Translated Set 2 keyboard as /class/input/input2 logips2pp: Detected unknown logitech mouse model 57 Bluetooth: HCI USB driver ver 2.9 usbcore: registered new driver hci_usb ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/none/1.1.2.2 PPP BSD Compression module registered HiSax: Linux Driver for passive ISDN cards HiSax: Version 3.5 (kernel) HiSax: Layer1 Revision 2.46.2.5 HiSax: Layer2 Revision 2.30.2.4 HiSax: TeiMgr Revision 2.20.2.3 HiSax: Layer3 Revision 2.22.2.3 HiSax: LinkLayer Revision 2.59.2.4 HiSax: Total 1 card defined HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) HiSax: Teles/PCI driver Rev. 2.23.2.3 ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 19 Found: Zoran, base-address: 0xdb800000, irq: 0x13 HiSax: Teles PCI config irq:19 mem:e084e000 TelesPCI: ISAC version (0): 2086/2186 V1.1 TelesPCI: HSCX version A: V2.1 B: V2.1 Teles PCI: IRQ 19 count 0 Teles PCI: IRQ 19 count 0 Teles PCI: IRQ(19) getting no interrupts during init 1 Teles PCI: IRQ 19 count 0 Teles PCI: IRQ(19) getting no interrupts during init 2 Teles PCI: IRQ 19 count 0 Teles PCI: IRQ(19) getting no interrupts during init 3 HiSax: Card Teles PCI not installed ! Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC). input: ImExPS/2 Logitech Explorer Mouse as /class/input/input3 specify port snd_mpu401: probe of snd_mpu401.0 failed with error -22 ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 18 ALSA device list: #0: SBLive 5.1 [SB0060] (rev.7, serial:0x80611102) at 0xa800, irq 18 ip_conntrack version 2.4 (4095 buckets, 32760 max) - 192 bytes per conntrack TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 IrCOMM protocol (Dag Brattli) Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 Bluetooth: BNEP (Ethernet Emulation) ver 1.2 Bluetooth: BNEP filters: protocol multicast Using IPI Shortcut mode saa7134 ALSA driver for DMA sound loaded saa7134[0]/alsa: saa7134[0] at 0xdc000000 irq 17 registered as card -1 Time: tsc clocksource has been installed. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 200k freed e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex hdd: No disk in drive hdd: No disk in drive Adding 1052248k swap on /dev/disk/by-uuid/ff8135cc-d5e6-40b8-b9dd-fd8ab1245cac. Priority:-1 extents:1 across:1052248k EXT3 (no)user_xattr options not supported EXT3 FS on sda2, internal journal sr0: CDROM not ready. Make sure there is a disc in the drive. XFS mounting filesystem sda3 Starting XFS recovery on filesystem: sda3 (logdev: internal) Ending XFS recovery on filesystem: sda3 (logdev: internal) XFS mounting filesystem hda1 Ending clean XFS mount for filesystem: hda1 XFS mounting filesystem hdb1 Ending clean XFS mount for filesystem: hdb1 NTFS volume version 3.1.