Linux version 2.6.17-1.2174_FC5 (brewbuilder@hs20-bc2-3.build.redhat.com) (gcc version 4.1.1 20060525 (Red Hat 4.1.1-1)) #1 Tue Aug 8 15:30:55 EDT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fffb000 (usable) BIOS-e820: 000000003fffb000 - 000000003ffff000 (ACPI data) BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 895MB LOWMEM available. Using x86 segment limits to approximate NX protection On node 0 totalpages: 262139 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225279 pages, LIFO batch:31 HighMem zone: 32764 pages, LIFO batch:7 DMI 2.3 present. ACPI: RSDP (v000 ASUS ) @ 0x000f5e20 ACPI: RSDT (v001 ASUS A7V600 0x42302e31 MSFT 0x31313031) @ 0x3fffb000 ACPI: FADT (v001 ASUS A7V600 0x42302e31 MSFT 0x31313031) @ 0x3fffb0b2 ACPI: BOOT (v001 ASUS A7V600 0x42302e31 MSFT 0x31313031) @ 0x3fffb030 ACPI: MADT (v001 ASUS A7V600 0x42302e31 MSFT 0x31313031) @ 0x3fffb058 ACPI: DSDT (v001 ASUS A7V600 0x00001000 MSFT 0x0100000b) @ 0x00000000 ACPI: PM-Timer IO Port: 0xe408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:10 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) Built 1 zonelists Kernel command line: ro root=/dev/md1 video=matroxfb:vesa:0x107 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c075c000 soft=c075b000 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2200.493 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1034076k/1048556k available (2068k kernel code, 13836k reserved, 1127k data, 216k init, 131056k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4404.79 BogoMIPS (lpj=8809590) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000420 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Athlon(TM) XP 3200+ stepping 00 Checking 'hlt' instruction... OK. ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking if image is initramfs... it is Freeing initrd memory: 921k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf1970, last bus=1 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 *6 7 9 10 11 12) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12) *15, disabled. ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Quirk-MSI-K8T Soundcard On PCI: Unexpected Value in PCI-Register: no Change! PCI: enabled onboard AC97/MC97 devices Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved pnp: 00:02: ioport range 0xe800-0xe81f has been reserved pnp: 00:0e: ioport range 0x290-0x297 has been reserved pnp: 00:0e: ioport range 0x370-0x375 has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: f4800000-f57fffff PREFETCH window: f5f00000-f7ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 8, 1310720 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x3a set to 0x1 apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1157717766.536:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 159031EDF350496D - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Bypassing VIA 8237 APIC De-Assert Message pci_hotplug: PCI Hot Plug PCI Core version: 0.5 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected VIA KT400/KT400A/KT600 chipset agpgart: AGP aperture is 64M @ 0xf8000000 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 169 PCI: VIA IRQ fixup for 0000:00:0f.1, from 14 to 9 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0x9800-0x9807, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x9808-0x980f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: ExcelStor Technology J840, ATA DISK drive hdb: ST340014A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: CREATIVE CD-RW RW1210E, ATAPI CD/DVD-ROM drive hdd: _NEC DVD_RW ND-1300A, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: 80418240 sectors (41174 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(133) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 hdb: max request size: 512KiB hdb: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) hdb: cache flushes supported hdb: hdb1 hdb2 hdb3 hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) ide-floppy driver 0.99.newide usbcore: registered new driver libusual usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Processor cpuid 6a0 not supported Using IPI Shortcut mode ACPI wakeup devices: PCI0 PCI1 USB0 USB1 USB2 USB3 SU20 MC97 ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 216k freed Write protecting the kernel read-only data: 705k input: AT Translated Set 2 keyboard as /class/input/input0 md: raid1 personality registered for level 1 md: Autodetecting RAID arrays. md: autorun ... md: considering hdb3 ... md: adding hdb3 ... md: hdb1 has different UUID to hdb3 md: adding hda3 ... md: hda1 has different UUID to hdb3 md: created md1 md: bind md: bind md: running: raid1: raid set md1 active with 2 out of 2 mirrors md: considering hdb1 ... md: adding hdb1 ... md: adding hda1 ... md: created md0 md: bind md: bind md: running: raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. input: PS/2 Generic Mouse as /class/input/input1 security: 3 users, 6 roles, 1468 types, 152 bools, 1 sens, 256 cats security: 58 classes, 43331 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev md1, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts audit(1157717771.540:2): policy loaded auid=4294967295 SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded PCI: Enabling device 0000:00:0a.0 (0014 -> 0017) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 16 (level, low) -> IRQ 177 eth0: Identified chip type is 'RTL8169s/8110s'. eth0: RTL8169 at 0xf8834000, 00:0f:b5:08:31:d5, IRQ 177 SCSI subsystem initialized PCI: Enabling device 0000:00:09.0 (0014 -> 0017) ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 185 skge 1.5 addr 0xf4000000 irq 185 chip Yukon rev 1 skge eth1: addr 00:0c:6e:6d:74:f6 libata version 1.20 loaded. sata_mv 0000:00:0d.0: version 0.7 ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 177 sata_mv 0000:00:0d.0: 32 slots 8 ports SCSI mode IRQ via INTx ata1: SATA max UDMA/133 cmd 0x0 ctl 0xF8A22120 bmdma 0x0 irq 177 ata2: SATA max UDMA/133 cmd 0x0 ctl 0xF8A24120 bmdma 0x0 irq 177 ata3: SATA max UDMA/133 cmd 0x0 ctl 0xF8A26120 bmdma 0x0 irq 177 ata4: SATA max UDMA/133 cmd 0x0 ctl 0xF8A28120 bmdma 0x0 irq 177 ata5: SATA max UDMA/133 cmd 0x0 ctl 0xF8A32120 bmdma 0x0 irq 177 ata6: SATA max UDMA/133 cmd 0x0 ctl 0xF8A34120 bmdma 0x0 irq 177 ata7: SATA max UDMA/133 cmd 0x0 ctl 0xF8A36120 bmdma 0x0 irq 177 ata8: SATA max UDMA/133 cmd 0x0 ctl 0xF8A38120 bmdma 0x0 irq 177 BUG: warning at drivers/scsi/sata_mv.c:1919/__msleep() (Not tainted) __mv_phy_reset+0xeb/0x3a7 [sata_mv] __freed_request+0x1f/0x6f mv_interrupt+0x209/0x310 [sata_mv] handle_IRQ_event+0x23/0x4c __do_IRQ+0x7c/0xd1 do_IRQ+0x63/0x80 ======================= common_interrupt+0x1a/0x20 kmap_atomic+0x75/0x7a file_read_actor+0x59/0xe0 do_generic_mapping_read+0x1b7/0x465 __generic_file_aio_read+0x167/0x1ac file_read_actor+0x0/0xe0 generic_file_aio_read+0x40/0x47 do_sync_read+0xc3/0xfd autoremove_wake_function+0x0/0x35 do_sync_read+0x0/0xfd vfs_read+0xa6/0x14e sys_read+0x41/0x67 syscall_call+0x7/0xb ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:bc01 87:4023 88:40ff ata1: dev 0 ATA-7, max UDMA7, 488397168 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_mv ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:bc01 87:4023 88:40ff ata2: dev 0 ATA-7, max UDMA7, 488397168 sectors: LBA48 ata2: dev 0 configured for UDMA/133 scsi1 : sata_mv ata3: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:bc01 87:4023 88:40ff ata3: dev 0 ATA-7, max UDMA7, 488397168 sectors: LBA48 ata3: dev 0 configured for UDMA/133 scsi2 : sata_mv ata4: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:bc01 87:4023 88:40ff ata4: dev 0 ATA-7, max UDMA7, 488397168 sectors: LBA48 ata4: dev 0 configured for UDMA/133 scsi3 : sata_mv ata5: no device found (phy stat 00000000) scsi4 : sata_mv ata6: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:bc01 87:4023 88:40ff ata6: dev 0 ATA-7, max UDMA7, 488397168 sectors: LBA48 ata6: dev 0 configured for UDMA/133 scsi5 : sata_mv ata7: no device found (phy stat 00000000) scsi6 : sata_mv ata8: no device found (phy stat 00000000) scsi7 : sata_mv Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10 Type: Direct-Access ANSI SCSI revision: 05 sata_via 0000:00:0f.0: version 1.1 ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 20 (level, low) -> IRQ 169 sata_via 0000:00:0f.0: routed to hard irq line 0 ata9: SATA max UDMA/133 cmd 0xB800 ctl 0xB402 bmdma 0xA400 irq 169 ata10: SATA max UDMA/133 cmd 0xB000 ctl 0xA802 bmdma 0xA408 irq 169 ata9: SATA link down (SStatus 0) scsi8 : sata_via ata10: SATA link down (SStatus 0) scsi9 : sata_via PCI: Enabling device 0000:00:11.6 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:11.6 to 64 VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13 ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:11.5 to 64 codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] 0:0:0:0: Attached scsi generic sg0 type 0 1:0:0:0: Attached scsi generic sg1 type 0 2:0:0:0: Attached scsi generic sg2 type 0 3:0:0:0: Attached scsi generic sg3 type 0 5:0:0:0: Attached scsi generic sg4 type 0 ieee1394: Initialized config rom entry `ip1394' USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 201 PCI: VIA IRQ fixup for 0000:00:10.0, from 0 to 9 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:10.0: irq 201, io base 0x00009400 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: unknown partition table sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: unknown partition table sd 1:0:0:0: Attached scsi disk sdb SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back sdc: unknown partition table sd 2:0:0:0: Attached scsi disk sdc SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB) sdd: Write Protect is off sdd: Mode Sense: 00 3a 00 00 SCSI device sdd: drive cache: write back SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB) sdd: Write Protect is off sdd: Mode Sense: 00 3a 00 00 SCSI device sdd: drive cache: write back sdd:<6>ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 201 PCI: VIA IRQ fixup for 0000:00:10.1, from 0 to 9 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.1: irq 201, io base 0x00009000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected unknown partition table sd 3:0:0:0: Attached scsi disk sdd SCSI device sde: 488397168 512-byte hdwr sectors (250059 MB) sde: Write Protect is off sde: Mode Sense: 00 3a 00 00 SCSI device sde: drive cache: write back SCSI device sde: 488397168 512-byte hdwr sectors (250059 MB) sde: Write Protect is off sde: Mode Sense: 00 3a 00 00 SCSI device sde: drive cache: write back sde: unknown partition table sd 5:0:0:0: Attached scsi disk sde ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 201 PCI: VIA IRQ fixup for 0000:00:10.2, from 0 to 9 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.2: irq 201, io base 0x00008800 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 201 PCI: VIA IRQ fixup for 0000:00:10.3, from 0 to 9 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.3: irq 201, io base 0x00008400 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected PCI: Enabling device 0000:00:0e.0 (0014 -> 0016) ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 209 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209] MMIO=[f2000000-f20007ff] Max Packet=[1024] IR/IT contexts=[4/4] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 201 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: irq 201, io mem 0xf1800000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected BUG: warning at drivers/ieee1394/ohci1394.c:3181/ohci_hw_csr_reg() (Not tainted) ohci_hw_csr_reg+0x85/0xa3 [ohci1394] ohci_hw_csr_reg+0x0/0xa3 [ohci1394] host_reset+0x6e/0x114 [ieee1394] highlevel_host_reset+0x21/0x42 [ieee1394] ohci_irq_handler+0x6b9/0x73d [ohci1394] scheduler_tick+0x1a/0x2af handle_IRQ_event+0x23/0x4c __do_IRQ+0x7c/0xd1 do_IRQ+0x63/0x80 ======================= common_interrupt+0x1a/0x20 _spin_unlock_irqrestore+0xa/0xc ohci_devctl+0x5d/0x5de [ohci1394] hpsb_reset_bus+0x1c/0x22 [ieee1394] run_workqueue+0x85/0xc5 remove_wait_queue+0xaf/0xb9 delayed_reset_bus+0x0/0xca [ieee1394] worker_thread+0x0/0x10c worker_thread+0xdb/0x10c default_wake_function+0x0/0xc kthread+0x91/0xbd kthread+0x0/0xbd kernel_thread_helper+0x5/0xb ieee1394: Error parsing configrom for node 0-00:1023 ieee1394: Host added: ID:BUS[0-01:1023] GUID[00c0d00001f79969] floppy0: no floppy controllers found parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] lp0: using parport0 (interrupt-driven). lp0: console ready ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ibm_acpi: ec object not found md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. md: md3 stopped. device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com EXT3 FS on md1, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on md0, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev md0, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs ext3: No journal on filesystem on hdb2 Adding 1000432k swap on /dev/hda2. Priority:-1 extents:1 across:1000432k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts r8169: eth0: link up skge eth1: enabling interface skge eth1: disabling interface audit(1157717802.877:3): audit_pid=2108 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0 SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts ext3: No journal on filesystem on hdb2 Bluetooth: Core ver 2.8 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: HIDP (Human Interface Emulation) ver 1.1 it87: Found IT8712F chip at 0x290, revision 5 SELinux: initialized (dev autofs, type autofs), uses genfs_contexts NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver Installing knfsd (copyright (C) 1996 okir@monad.swb.de). SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period eth0: no IPv6 routers present md: md3 stopped. md: md3 stopped. md: bind md: bind md: bind md: bind md: bind raid5: automatically using best checksumming function: pIII_sse pIII_sse : 3756.000 MB/sec raid5: using function: pIII_sse (3756.000 MB/sec) raid6: int32x1 808 MB/s raid6: int32x2 917 MB/s raid6: int32x4 825 MB/s raid6: int32x8 568 MB/s raid6: mmxx1 1808 MB/s raid6: mmxx2 3050 MB/s raid6: sse1x1 1638 MB/s raid6: sse1x2 2826 MB/s raid6: using algorithm sse1x2 (2826 MB/s) md: raid6 personality registered for level 6 raid6: device sdc operational as raid disk 0 raid6: device sde operational as raid disk 4 raid6: device sdb operational as raid disk 3 raid6: device sda operational as raid disk 2 raid6: device sdd operational as raid disk 1 raid6: allocated 6289kB for md3 raid6: raid level 6 set md3 active with 5 out of 6 devices, algorithm 2 RAID6 conf printout: --- rd:6 wd:5 fd:1 disk 0, o:1, dev:sdc disk 1, o:1, dev:sdd disk 2, o:1, dev:sda disk 3, o:1, dev:sdb disk 4, o:1, dev:sde kjournald starting. Commit interval 5 seconds EXT3 FS on md3, internal journal EXT3-fs: mounted filesystem with journal data mode. SELinux: initialized (dev md3, type ext3), uses xattr [drm] Initialized drm 1.0.1 20051102 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177 [drm] Initialized mga 3.2.1 20051102 on minor 0 agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Device is in legacy mode, falling back to 2.x agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Initialized card for AGP DMA. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177 matroxfb: Matrox G550 detected PInS memtype = 5 matroxfb: MTRR's turned on matroxfb: 640x480x8bpp (virtual: 640x26214) matroxfb: framebuffer at 0xF6000000, mapped to 0xf9880000, size 33554432 Console: switching to colour frame buffer device 80x30 fb0: MATROX frame buffer device