Message-ID: <489ecd0c0609202033j4dd9a62fye81f99d61bff030d@mail.gmail.com>
Date:	Thu, 21 Sep 2006 11:33:05 +0800
From:	"Luke Yang" <luke.adi@...il.com>
To:	linux-kernel@...r.kernel.org, "Andrew Morton" <akpm@...l.org>
Subject: [PATCH 2/4] Blackfin: Serial driver for Blackfin arch on 2.6.18

Hi,

This is the serial driver for Blackfin. It is designed for the serial
core framework.

As to other drivers, I'll send them one by one later.

Signed-off-by: Luke Yang <luke.adi@...il.com>

 drivers/serial/Kconfig      |   35 +
 drivers/serial/Makefile     |    3
 drivers/serial/bfin_5xx.c   |  903 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/serial_core.h |    3
 4 files changed, 943 insertions(+), 1 deletion(-)

diff -urN linux-2.6.18.patch1/drivers/serial/Kconfig
linux-2.6.18.patch2/drivers/serial/Kconfig
--- linux-2.6.18.patch1/drivers/serial/Kconfig	2006-09-21
09:14:42.000000000 +0800
+++ linux-2.6.18.patch2/drivers/serial/Kconfig	2006-09-21
09:38:17.000000000 +0800
@@ -488,6 +488,41 @@
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)

+config SERIAL_BFIN
+	bool "Blackfin serial port support (EXPERIMENTAL)"
+	depends on BFIN && EXPERIMENTAL
+	select SERIAL_CORE
+
+config SERIAL_BFIN_CONSOLE
+	bool "Console on Blackfin serial port"
+	depends on SERIAL_BFIN
+	select SERIAL_CORE_CONSOLE
+
+choice
+        prompt  "Blackfin UART Mode"
+        depends on SERIAL_BFIN
+        default SERIAL_BFIN_DMA
+        ---help---
+          This driver supports the built-in serial ports of the
Blackfin family of CPUs
+
+config SERIAL_BFIN_DMA
+        bool "Blackfin UART DMA mode"
+        depends on DMA_UNCACHED_1M
+        help
+          This driver works under DMA mode. If this option is
selected, the blackfin simple dma driver is also enabled.
+
+config SERIAL_BFIN_PIO
+        bool "Blackfin UART PIO mode"
+        help
+          This driver works under PIO mode.
+endchoice
+
+config SERIAL_BFIN_CTSRTS
+	bool "Enable hardware flow control"
+	depends on SERIAL_BFIN
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the
CTS/RTS signal.
+
 config SERIAL_IMX
 	bool "IMX serial port support"
 	depends on ARM && ARCH_IMX
diff -urN linux-2.6.18.patch1/drivers/serial/Makefile
linux-2.6.18.patch2/drivers/serial/Makefile
--- linux-2.6.18.patch1/drivers/serial/Makefile	2006-09-21
09:14:42.000000000 +0800
+++ linux-2.6.18.patch2/drivers/serial/Makefile	2006-09-21
09:38:17.000000000 +0800
@@ -25,6 +25,7 @@
 obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
 obj-$(CONFIG_SERIAL_PXA) += pxa.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
 obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
 obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
 obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o
@@ -55,4 +56,4 @@
 obj-$(CONFIG_SERIAL_SGI_IOC4) += ioc4_serial.o
 obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
 obj-$(CONFIG_SERIAL_AT91) += at91_serial.o
-obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
+obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
\ No newline at end of file
diff -urN linux-2.6.18.patch1/drivers/serial/bfin_5xx.c
linux-2.6.18.patch2/drivers/serial/bfin_5xx.c
--- linux-2.6.18.patch1/drivers/serial/bfin_5xx.c	1970-01-01
08:00:00.000000000 +0800
+++ linux-2.6.18.patch2/drivers/serial/bfin_5xx.c	2006-09-21
09:38:17.000000000 +0800
@@ -0,0 +1,903 @@
+/*
+ * File:         drivers/serial/bfin_5xx.c
+ * Based on:     Based on drivers/serial/sa1100.c
+ * Author:       Aubrey Li <aubrey.li@...log.com>
+ *
+ * Created:
+ * Description:  Driver for blackfin 5xx serial ports
+ *
+ * Rev:          $Id: bfin_5xx.c,v 1.12 2006/09/04 04:44:27 aubrey Exp $
+ *
+ * Modified:
+ *               Copyright 2006 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/config.h>
+
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/bfin_serial_5xx.h>
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+#include <linux/dma-mapping.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/cacheflush.h>
+#endif
+
+/* We've been assigned a range on the "Low-density serial ports" major */
+#define SERIAL_BFIN_MAJOR	TTY_MAJOR
+#define MINOR_START		64
+
+#define DEBUG
+
+#ifdef DEBUG
+# define DPRINTK(x...)   printk(KERN_DEBUG x)
+#else
+# define DPRINTK(x...)   do { } while (0)
+#endif
+
+/*
+ * Setup for console. Argument comes from the menuconfig
+ */
+
+#if defined(CONFIG_BAUD_9600)
+#define CONSOLE_BAUD_RATE       9600
+#elif defined(CONFIG_BAUD_19200)
+#define CONSOLE_BAUD_RATE       19200
+#elif defined(CONFIG_BAUD_38400)
+#define CONSOLE_BAUD_RATE       38400
+#elif defined(CONFIG_BAUD_57600)
+#define CONSOLE_BAUD_RATE       57600
+#elif defined(CONFIG_BAUD_115200)
+#define CONSOLE_BAUD_RATE       115200
+#endif
+
+#define DMA_RX_XCOUNT		TTY_FLIPBUF_SIZE
+#define DMA_RX_YCOUNT		(PAGE_SIZE / DMA_RX_XCOUNT)
+
+#define DMA_RX_FLUSH_JIFFIES	5
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+wait_queue_head_t bfin_serial_tx_queue[NR_PORTS];
+static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
+#else
+static void bfin_serial_do_work(void *);
+static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
+static void local_put_char(struct bfin_serial_port *uart, char ch);
+#endif
+
+static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
+
+/*
+ * interrupts disabled on entry
+ */
+static void bfin_serial_stop_tx(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	unsigned short ier;
+	ier = UART_GET_IER(uart);
+	ier &= ~ETBEI;
+	UART_PUT_IER(uart, ier);
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	disable_dma(uart->tx_dma_channel);
+#endif
+}
+
+/*
+ * port locked and interrupts disabled
+ */
+static void bfin_serial_start_tx(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	bfin_serial_dma_tx_chars(uart);
+#else
+	unsigned short ier;
+	ier = UART_GET_IER(uart);
+	ier |= ETBEI;
+	UART_PUT_IER(uart, ier);
+	bfin_serial_tx_chars(uart);
+#endif
+}
+
+/*
+ * Interrupts enabled
+ */
+static void bfin_serial_stop_rx(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	unsigned short ier;
+	ier = UART_GET_IER(uart);
+	ier &= ERBFI;
+	UART_PUT_IER(uart, ier);
+}
+
+/*
+ * Set the modem control timer to fire immediately.
+ */
+static void bfin_serial_enable_ms(struct uart_port *port)
+{
+}
+
+#ifdef CONFIG_SERIAL_BFIN_PIO
+static void local_put_char(struct bfin_serial_port *uart, char ch)
+{
+        unsigned short status;
+        int flags = 0;
+
+        local_irq_save(flags);
+
+        do {
+                status = UART_GET_LSR(uart);
+        } while (!(status & THRE));
+
+        UART_PUT_CHAR(uart, ch);
+        local_irq_restore(flags);
+}
+
+static void
+bfin_serial_rx_chars(struct bfin_serial_port *uart, struct pt_regs *regs)
+{
+	struct tty_struct *tty = uart->port.info->tty;
+	unsigned int status=0, ch, flg;
+	ch = UART_GET_CHAR(uart);
+	uart->port.icount.rx++;
+	flg = TTY_NORMAL;
+	if (uart_handle_sysrq_char(&uart->port, ch, regs))
+		goto ignore_char;
+	uart_insert_char(&uart->port, status, 1, ch, flg);
+
+ignore_char:
+	tty_flip_buffer_push(tty);
+}
+
+static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
+{
+	struct circ_buf *xmit = &uart->port.info->xmit;
+
+	if (uart->port.x_char) {
+		UART_PUT_CHAR(uart, uart->port.x_char);
+		uart->port.icount.tx++;
+		uart->port.x_char = 0;
+		return;
+	}
+	/*
+	 * Check the modem control lines before
+	 * transmitting anything.
+	 */
+	bfin_serial_mctrl_check(uart);
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+		bfin_serial_stop_tx(&uart->port);
+		return;
+	}
+
+	local_put_char(uart, xmit->buf[xmit->tail]);
+	xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+	uart->port.icount.tx++;
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(&uart->port);
+
+	if (uart_circ_empty(xmit))
+		bfin_serial_stop_tx(&uart->port);
+}
+
+static irqreturn_t bfin_serial_int(int irq, void *dev_id, struct pt_regs *regs)
+{
+	struct bfin_serial_port *uart = dev_id;
+	unsigned short status;
+
+	spin_lock(&uart->port.lock);
+	status = UART_GET_IIR(uart);
+	do {
+		if ((status & IIR_STATUS) == IIR_TX_READY)
+			bfin_serial_tx_chars(uart);
+		if ((status & IIR_STATUS) == IIR_RX_READY)
+			bfin_serial_rx_chars(uart, regs);
+		status = UART_GET_IIR(uart);
+	} while (status &(IIR_TX_READY | IIR_RX_READY));
+	spin_unlock(&uart->port.lock);
+	return IRQ_HANDLED;
+}
+
+static void bfin_serial_do_work(void *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	bfin_serial_mctrl_check(uart);
+}
+
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
+{
+	struct circ_buf *xmit = &uart->port.info->xmit;
+	unsigned short ier;
+	int flags = 0;
+
+	if (!uart->tx_done)
+		return;
+
+	uart->tx_done = 0;
+
+	if (uart->port.x_char) {
+		UART_PUT_CHAR(uart, uart->port.x_char);
+		uart->port.icount.tx++;
+		uart->port.x_char = 0;
+		uart->tx_done = 1;
+		return;
+	}
+	/*
+	 * Check the modem control lines before
+	 * transmitting anything.
+	 */
+	bfin_serial_mctrl_check(uart);
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+		bfin_serial_stop_tx(&uart->port);
+		uart->tx_done = 1;
+		return;
+	}
+
+	local_irq_save(flags);
+	uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
+	if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
+	uart->tx_count = UART_XMIT_SIZE - xmit->tail;
+	blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
+					(unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
+	set_dma_config(uart->tx_dma_channel,
+		set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
+			INTR_ON_BUF,
+			DIMENSION_LINEAR,
+			DATA_SIZE_8));
+	set_dma_start_addr(uart->tx_dma_channel, (unsigned
long)(xmit->buf+xmit->tail));
+	set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
+	set_dma_x_modify(uart->tx_dma_channel, 1);
+	enable_dma(uart->tx_dma_channel);
+	ier = UART_GET_IER(uart);
+	ier |= ETBEI;
+	UART_PUT_IER(uart, ier);
+	local_irq_restore(flags);
+}
+
+static void bfin_serial_dma_rx_chars(struct bfin_serial_port * uart)
+{
+	struct tty_struct *tty = uart->port.info->tty;
+	int i, flg, status = 0;
+
+	uart->port.icount.rx += CIRC_CNT(uart->rx_dma_buf.head,
uart->rx_dma_buf.tail, UART_XMIT_SIZE);;
+	flg = TTY_NORMAL;
+	for (i = uart->rx_dma_buf.head; i < uart->rx_dma_buf.tail; i++) {
+		if (uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i], NULL))
+			goto dma_ignore_char;
+		uart_insert_char(&uart->port, status, 1, uart->rx_dma_buf.buf[i], flg);
+	}
+dma_ignore_char:
+	tty_flip_buffer_push(tty);
+}
+
+void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
+{
+	int x_pos, pos;
+	int flags = 0;
+
+	bfin_serial_dma_tx_chars(uart);
+
+	local_irq_save(flags);
+	x_pos = DMA_RX_XCOUNT - get_dma_curr_xcount(uart->rx_dma_channel);
+	if (x_pos == DMA_RX_XCOUNT)
+		x_pos = 0;
+
+	pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
+
+	if (pos>uart->rx_dma_buf.tail) {
+		uart->rx_dma_buf.tail = pos;
+		bfin_serial_dma_rx_chars(uart);
+		uart->rx_dma_buf.head = uart->rx_dma_buf.tail;
+	}
+	local_irq_restore(flags);
+	uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
+	add_timer(&(uart->rx_dma_timer));
+}
+
+static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id,
struct pt_regs *regs)
+{
+	struct bfin_serial_port *uart = dev_id;
+	struct circ_buf *xmit = &uart->port.info->xmit;
+	unsigned short ier;
+
+	spin_lock(&uart->port.lock);
+	if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
+		clear_dma_irqstat(uart->tx_dma_channel);
+		disable_dma(uart->tx_dma_channel);
+		ier = UART_GET_IER(uart);
+		ier &= ~ETBEI;
+		UART_PUT_IER(uart, ier);
+		xmit->tail = (xmit->tail+uart->tx_count) &(UART_XMIT_SIZE -1);
+		uart->port.icount.tx+=uart->tx_count;
+
+		if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+			uart_write_wakeup(&uart->port);
+
+		if (uart_circ_empty(xmit))
+			bfin_serial_stop_tx(&uart->port);
+		uart->tx_done = 1;
+	}
+
+	spin_unlock(&uart->port.lock);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id,
struct pt_regs *regs)
+{
+	struct bfin_serial_port *uart = dev_id;
+	unsigned short irqstat;
+
+	uart->rx_dma_nrows++;
+	if (uart->rx_dma_nrows == DMA_RX_YCOUNT) {
+		uart->rx_dma_nrows = 0;
+		uart->rx_dma_buf.tail = DMA_RX_XCOUNT*DMA_RX_YCOUNT;
+		bfin_serial_dma_rx_chars(uart);
+		uart->rx_dma_buf.head = uart->rx_dma_buf.tail = 0;
+	}
+	spin_lock(&uart->port.lock);
+	irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
+	clear_dma_irqstat(uart->rx_dma_channel);
+
+	spin_unlock(&uart->port.lock);
+	return IRQ_HANDLED;
+}
+#endif
+
+/*
+ * Return TIOCSER_TEMT when transmitter is not busy.
+ */
+static unsigned int bfin_serial_tx_empty(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	unsigned short lsr;
+	lsr = UART_GET_LSR(uart);
+	if (lsr & THRE)
+		return TIOCSER_TEMT;
+	else
+		return 0;
+}
+
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	if (bfin_read16(CTS_PORT) & (1<<CTS_PIN))
+		return TIOCM_DSR | TIOCM_CAR;
+	else
+#endif
+		return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	if (mctrl & TIOCM_RTS)
+		bfin_write16(RTS_PORT, bfin_read16(RTS_PORT)&(~1<<RTS_PIN));
+	else
+		bfin_write16(RTS_PORT, bfin_read16(RTS_PORT)|(1<<RTS_PIN));
+#endif
+}
+
+/*
+ * Handle any change of modem status signal since we were last called.
+ */
+static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	unsigned int status;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	struct uart_info *info = uart->port.info;
+	struct tty_struct *tty = info->tty;
+	status = bfin_serial_get_mctrl(&uart->port);
+	if (!(status & TIOCM_CTS)) {
+		tty->hw_stopped = 1;
+	} else {
+		tty->hw_stopped = 0;
+	}
+#else
+	status = bfin_serial_get_mctrl(&uart->port);
+	uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+	if (!(status & TIOCM_CTS))
+		schedule_work(&uart->cts_workqueue);
+#endif
+#endif
+}
+
+/*
+ * Interrupts always disabled.
+ */
+static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
+{
+}
+
+int bfin_serial_startup(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	dma_addr_t dma_handle;
+
+	if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
+		printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
+		return -EBUSY;
+	} else
+		set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
+
+	if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
+		printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
+		return -EBUSY;
+	} else
+		set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
+
+	uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL,
PAGE_SIZE, &dma_handle, GFP_DMA);
+	uart->rx_dma_buf.head = 0;
+	uart->rx_dma_buf.tail = 0;
+	uart->rx_dma_nrows = 0;
+
+	set_dma_config(uart->rx_dma_channel,
+		set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
+				INTR_ON_ROW, DIMENSION_2D,
+				DATA_SIZE_8));
+	set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
+	set_dma_x_modify(uart->rx_dma_channel, 1);
+	set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
+	set_dma_y_modify(uart->rx_dma_channel, 1);
+	set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
+	enable_dma(uart->rx_dma_channel);
+
+	uart->rx_dma_timer.data = (unsigned long)(uart);
+	uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
+	uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
+	add_timer(&(uart->rx_dma_timer));
+#else
+	if (request_irq
+	    (uart->port.irq, bfin_serial_int, SA_INTERRUPT | SA_SHIRQ,
+	     "BFIN_UART0_RX", uart)) {
+		printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
+		return -EBUSY;
+	}
+
+	if (request_irq
+	    (uart->port.irq+1, bfin_serial_int, SA_INTERRUPT | SA_SHIRQ,
+	     "BFIN_UART0_TX", uart)) {
+		printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
+		return -EBUSY;
+	}
+#endif
+	UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
+	return 0;
+}
+
+static void bfin_serial_shutdown(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	disable_dma(uart->tx_dma_channel);
+	free_dma(uart->tx_dma_channel);
+	disable_dma(uart->rx_dma_channel);
+	free_dma(uart->rx_dma_channel);
+	del_timer(&(uart->rx_dma_timer));
+#else
+	free_irq(uart->port.irq, uart);
+	free_irq(uart->port.irq+1, uart);
+#endif
+}
+
+static void
+bfin_serial_set_termios(struct uart_port *port, struct termios *termios,
+		   struct termios *old)
+{
+}
+
+static const char *bfin_serial_type(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'.
+ */
+static void bfin_serial_release_port(struct uart_port *port)
+{
+}
+
+/*
+ * Request the memory region(s) being used by 'port'.
+ */
+static int bfin_serial_request_port(struct uart_port *port)
+{
+	return 0;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void bfin_serial_config_port(struct uart_port *port, int flags)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+	if (flags & UART_CONFIG_TYPE &&
+	    bfin_serial_request_port(&uart->port) == 0)
+		uart->port.type = PORT_BFIN;
+}
+
+/*
+ * Verify the new serial_struct (for TIOCSSERIAL).
+ * The only change we allow are to the flags and type, and
+ * even then only between PORT_BFIN and PORT_UNKNOWN
+ */
+static int
+bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	return 0;
+}
+
+static struct uart_ops bfin_serial_pops = {
+	.tx_empty	= bfin_serial_tx_empty,
+	.set_mctrl	= bfin_serial_set_mctrl,
+	.get_mctrl	= bfin_serial_get_mctrl,
+	.stop_tx	= bfin_serial_stop_tx,
+	.start_tx	= bfin_serial_start_tx,
+	.stop_rx	= bfin_serial_stop_rx,
+	.enable_ms	= bfin_serial_enable_ms,
+	.break_ctl	= bfin_serial_break_ctl,
+	.startup	= bfin_serial_startup,
+	.shutdown	= bfin_serial_shutdown,
+	.set_termios	= bfin_serial_set_termios,
+	.type		= bfin_serial_type,
+	.release_port	= bfin_serial_release_port,
+	.request_port	= bfin_serial_request_port,
+	.config_port	= bfin_serial_config_port,
+	.verify_port	= bfin_serial_verify_port,
+};
+
+static int bfin_serial_calc_baud(unsigned int uartclk)
+{
+	int baud;
+	baud = get_sclk()/(uartclk*8);
+	if ((baud & 0x1) == 1) {
+		baud++;
+	}
+	return baud/2;
+}
+
+static void __init bfin_serial_init_ports(void)
+{
+	static int first = 1;
+	int i;
+	unsigned short val;
+	int baud;
+
+	if (!first)
+		return;
+	first = 0;
+	bfin_serial_hw_init();
+
+	for (i = 0; i < NR_PORTS; i++) {
+		bfin_serial_ports[i].port.uartclk   = CONSOLE_BAUD_RATE;
+		bfin_serial_ports[i].port.ops       = &bfin_serial_pops;
+		bfin_serial_ports[i].port.line      = i;
+		bfin_serial_ports[i].port.iotype    = UPIO_MEM;
+		bfin_serial_ports[i].port.membase   = (void __iomem *)uart_base_addr[i];
+		bfin_serial_ports[i].port.mapbase   = uart_base_addr[i];
+		bfin_serial_ports[i].port.irq       = uart_irq[i];
+		bfin_serial_ports[i].port.flags     = UPF_BOOT_AUTOCONF;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+		bfin_serial_ports[i].tx_done	    = 1;
+		bfin_serial_ports[i].tx_count	    = 0;
+		bfin_serial_ports[i].tx_dma_channel = uart_tx_dma_channel[i];
+		bfin_serial_ports[i].rx_dma_channel = uart_rx_dma_channel[i];
+
+		init_timer(&(bfin_serial_ports[i].rx_dma_timer));
+#else
+		INIT_WORK(&bfin_serial_ports[i].cts_workqueue, bfin_serial_do_work,
&bfin_serial_ports[i]);
+#endif
+
+		baud = bfin_serial_calc_baud(bfin_serial_ports[i].port.uartclk);
+
+		/* Enable UART */
+		val = UART_GET_GCTL(&bfin_serial_ports[i]);
+		val |= UCEN;
+		UART_PUT_GCTL(&bfin_serial_ports[i], val);
+
+		/* Set DLAB in LCR to Access DLL and DLH */
+		val = UART_GET_LCR(&bfin_serial_ports[i]);
+		val |= DLAB;
+		UART_PUT_LCR(&bfin_serial_ports[i], val);
+
+		UART_PUT_DLL(&bfin_serial_ports[i], baud&0xFF);
+		UART_PUT_DLH(&bfin_serial_ports[i], (baud>>8)&0xFF);
+
+		/* Clear DLAB in LCR to Access THR RBR IER */
+		val = UART_GET_LCR(&bfin_serial_ports[i]);
+		val &= ~DLAB;
+		UART_PUT_LCR(&bfin_serial_ports[i], val);
+
+		/* Set LCR to Word Lengh 8-bit word select */
+		val = WLS(8);
+		UART_PUT_LCR(&bfin_serial_ports[i], val);
+	}
+}
+
+#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+/*
+ * Interrupts are disabled on entering
+ */
+static void
+bfin_serial_console_write(struct console *co, const char *s, unsigned
int count)
+{
+	struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
+	int flags = 0;
+	unsigned short status, tmp;
+	int i;
+
+	local_irq_save(flags);
+
+	for (i = 0; i < count; i++) {
+		do {
+			status = UART_GET_LSR(uart);
+		} while (!(status & THRE));
+
+		tmp = UART_GET_LCR(uart);
+		tmp &= ~DLAB;
+		UART_PUT_LCR(uart, tmp);
+
+		UART_PUT_CHAR(uart, s[i]);
+		if (s[i] == '\n') {
+			do {
+				status = UART_GET_LSR(uart);
+			} while(!(status & THRE));
+			UART_PUT_CHAR(uart, '\r');
+		}
+	}
+
+	local_irq_restore(flags);
+}
+
+/*
+ * If the port was already initialised (eg, by a boot loader),
+ * try to determine the current setup.
+ */
+static void __init
+bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
+			   int *parity, int *bits)
+{
+	unsigned short status;
+
+	status = UART_GET_IER(uart) & (ERBFI | ETBEI);
+	if (status == (ERBFI | ETBEI)) {
+		/* ok, the port was enabled */
+		unsigned short lcr, val;
+		unsigned short dlh, dll;
+
+		lcr = UART_GET_LCR(uart);
+
+		*parity = 'n';
+		if (lcr & PEN) {
+			if (lcr & EPS)
+				*parity = 'e';
+			else
+				*parity = 'o';
+		}
+		switch (lcr & 0x03) {
+			case 0:	*bits = 5; break;
+			case 1:	*bits = 6; break;
+			case 2:	*bits = 7; break;
+			case 3:	*bits = 8; break;
+		}
+		/* Set DLAB in LCR to Access DLL and DLH */
+		val = UART_GET_LCR(uart);
+		val |= DLAB;
+		UART_PUT_LCR(uart, val);
+
+		dll = UART_GET_DLL(uart);
+		dlh = UART_GET_DLH(uart);
+
+		/* Clear DLAB in LCR to Access THR RBR IER */
+		val = UART_GET_LCR(uart);
+		val &= ~DLAB;
+		UART_PUT_LCR(uart, val);
+
+		*baud = get_sclk()/(16*(dll|dlh<<8));
+	}
+	DPRINTK("%s:baud = %d, parity = %c, bits= %d\n", __FUNCTION__,
*baud, *parity, *bits);
+}
+
+static int __init
+bfin_serial_console_setup(struct console *co, char *options)
+{
+	struct bfin_serial_port *uart;
+	int baud = CONSOLE_BAUD_RATE;
+	int bits = 8;
+	int parity = 'n';
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	int flow = 'r';
+#else
+	int flow = 'n';
+#endif
+
+	/*
+	 * Check whether an invalid uart number has been specified, and
+	 * if so, search for the first available port that does have
+	 * console support.
+	 */
+	if (co->index == -1 || co->index >= NR_PORTS)
+		co->index = 0;
+	uart = &bfin_serial_ports[co->index];
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+	else
+		bfin_serial_console_get_options(uart, &baud, &parity, &bits);
+
+	return uart_set_options(&uart->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver bfin_serial_reg;
+static struct console bfin_serial_console = {
+	.name		= "ttyS",
+	.write		= bfin_serial_console_write,
+	.device		= uart_console_device,
+	.setup		= bfin_serial_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &bfin_serial_reg,
+};
+
+static int __init bfin_serial_rs_console_init(void)
+{
+	bfin_serial_init_ports();
+	register_console(&bfin_serial_console);
+	return 0;
+}
+console_initcall(bfin_serial_rs_console_init);
+
+#define BFIN_SERIAL_CONSOLE	&bfin_serial_console
+#else
+#define BFIN_SERIAL_CONSOLE	NULL
+#endif
+
+static struct uart_driver bfin_serial_reg = {
+	.owner			= THIS_MODULE,
+	.driver_name		= "bfin-uart",
+	.dev_name		= "ttyS",
+	.major			= SERIAL_BFIN_MAJOR,
+	.minor			= MINOR_START,
+	.nr			= NR_PORTS,
+	.cons			= BFIN_SERIAL_CONSOLE,
+};
+
+static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
+{
+	struct bfin_serial_port *uart = platform_get_drvdata(dev);
+
+	if (uart)
+		uart_suspend_port(&bfin_serial_reg, &uart->port);
+
+	return 0;
+}
+
+static int bfin_serial_resume(struct platform_device *dev)
+{
+	struct bfin_serial_port *uart = platform_get_drvdata(dev);
+
+	if (uart)
+		uart_resume_port(&bfin_serial_reg, &uart->port);
+
+	return 0;
+}
+
+static int bfin_serial_probe(struct platform_device *dev)
+{
+	struct resource *res = dev->resource;
+	int i;
+
+	for (i = 0; i < dev->num_resources; i++, res++)
+		if (res->flags & IORESOURCE_MEM)
+			break;
+
+	if (i < dev->num_resources) {
+		for (i = 0; i < NR_PORTS; i++, res++) {
+			if (bfin_serial_ports[i].port.mapbase != res->start)
+				continue;
+			bfin_serial_ports[i].port.dev = &dev->dev;
+			uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+			platform_set_drvdata(dev, &bfin_serial_ports[i]);
+		}
+	}
+
+	return 0;
+}
+
+static int bfin_serial_remove(struct platform_device *pdev)
+{
+	struct bfin_serial_port *uart = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+
+	if (uart)
+		uart_remove_one_port(&bfin_serial_reg, &uart->port);
+
+	return 0;
+}
+
+static struct platform_driver bfin_serial_driver = {
+	.probe		= bfin_serial_probe,
+	.remove		= bfin_serial_remove,
+	.suspend	= bfin_serial_suspend,
+	.resume		= bfin_serial_resume,
+	.driver		= {
+		.name	= "bfin-uart",
+	},
+};
+
+static int __init bfin_serial_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "Serial: Blackfin serial driver\n");
+
+	bfin_serial_init_ports();
+
+	ret = uart_register_driver(&bfin_serial_reg);
+	if (ret == 0) {
+		ret = platform_driver_register(&bfin_serial_driver);
+		if (ret) {
+			DPRINTK("uart register failed\n");
+			uart_unregister_driver(&bfin_serial_reg);
+		}
+	}
+	return ret;
+}
+
+static void __exit bfin_serial_exit(void)
+{
+	platform_driver_unregister(&bfin_serial_driver);
+	uart_unregister_driver(&bfin_serial_reg);
+}
+
+module_init(bfin_serial_init);
+module_exit(bfin_serial_exit);
+
+MODULE_AUTHOR("Aubrey.Li <aubrey.li@...log.com>");
+MODULE_DESCRIPTION("Blackfin generic serial port driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_BFIN_MAJOR);
diff -urN linux-2.6.18.patch1/include/linux/serial_core.h
linux-2.6.18.patch2/include/linux/serial_core.h
--- linux-2.6.18.patch1/include/linux/serial_core.h	2006-09-21
09:14:54.000000000 +0800
+++ linux-2.6.18.patch2/include/linux/serial_core.h	2006-09-21
09:38:17.000000000 +0800
@@ -132,6 +132,9 @@

 #define PORT_S3C2412	73

+/* Blackfin bf5xx */
+#define PORT_BFIN	74
+

 #ifdef __KERNEL__

-- 
Best regards,
Luke Yang
luke.adi@...il.com

View attachment "blackfin_serial_drv_2.6.18.patch" of type "text/x-patch" (27271 bytes)

Powered by blists - more mailing lists