[ 0.000000] Linux version 2.6.18-mm1 (suka@elm3b166) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #4 SMP PREEMPT Tue Sep 26 18:11:58 PDT 2006 [ 0.000000] Command line: root=/dev/sda1 ro quiet console=ttyS0,57600 debug pci=noacpi acpi=off [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009ac00 (usable) [ 0.000000] BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff70000 (usable) [ 0.000000] BIOS-e820: 000000007ff70000 - 000000007ff7b000 (ACPI data) [ 0.000000] BIOS-e820: 000000007ff7b000 - 000000007ff80000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 154) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 524144) 1 entries of 3200 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] Number of nodes 2 [ 0.000000] Node 0 MemBase 0000000000000000 Limit 0000000040000000 [ 0.000000] Entering add_active_range(0, 0, 154) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 262144) 1 entries of 3200 used [ 0.000000] Node 1 MemBase 0000000040000000 Limit 000000007ff70000 [ 0.000000] Entering add_active_range(1, 262144, 524144) 2 entries of 3200 used [ 0.000000] NUMA: Using 30 for the hash shift. [ 0.000000] Using node hash shift of 30 [ 0.000000] Bootmem setup node 0 0000000000000000-0000000040000000 [ 0.000000] Bootmem setup node 1 0000000040000000-000000007ff70000 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 1048576 [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0 -> 154 [ 0.000000] 0: 256 -> 262144 [ 0.000000] 1: 262144 -> 524144 [ 0.000000] On node 0 totalpages: 262042 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1615 pages reserved [ 0.000000] DMA zone: 2323 pages, LIFO batch:0 [ 0.000000] Normal zone: 3528 pages used for memmap [ 0.000000] Normal zone: 254520 pages, LIFO batch:31 [ 0.000000] On node 1 totalpages: 262000 [ 0.000000] DMA zone: 0 pages used for memmap [ 0.000000] Normal zone: 3582 pages used for memmap [ 0.000000] Normal zone: 258418 pages, LIFO batch:31 [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: AMD MPTABLE: Product ID: HAMMER MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] Processor #1 [ 0.000000] I/O APIC #2 at 0xFEC00000. [ 0.000000] I/O APIC #3 at 0xE8000000. [ 0.000000] I/O APIC #4 at 0xE8001000. [ 0.000000] Setting APIC routing to physical flat [ 0.000000] Processors: 2 [ 0.000000] Nosave address range: 000000000009a000 - 000000000009b000 [ 0.000000] Nosave address range: 000000000009b000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000d0000 [ 0.000000] Nosave address range: 00000000000d0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 34176 bytes of per cpu data [ 0.000000] Built 2 zonelists. Total pages: 515261 [ 0.000000] Kernel command line: root=/dev/sda1 ro quiet console=ttyS0,57600 debug pci=noacpi acpi=off [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 95.697829] Console: colour VGA+ 80x25 [ 96.406338] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 96.422658] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 96.436902] Checking aperture... [ 96.443355] CPU 0: aperture @ 0 size 32 MB [ 96.457962] No AGP bridge found [ 96.464228] Your BIOS doesn't leave a aperture memory hole [ 96.475174] Please enable the IOMMU option in the BIOS setup [ 96.486466] This costs you 64 MB of RAM [ 96.535791] Mapping aperture over 65536 KB of RAM @ 4000000 [ 96.568325] Memory: 1992256k/2096576k available (3997k kernel code, 103912k reserved, 1437k data, 316k init) [ 96.663979] Calibrating delay using timer specific routine.. 4794.74 BogoMIPS (lpj=9589489) [ 96.680762] Mount-cache hash table entries: 256 [ 96.689925] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 96.704159] CPU: L2 Cache: 1024K (64 bytes/line) [ 96.713375] CPU 0/0 -> Node 0 [ 96.719325] SMP alternatives: switching to UP code [ 96.769355] Using local APIC timer interrupts. [ 96.819919] result 12461204 [ 96.825491] Detected 12.461 MHz APIC timer. [ 96.835806] SMP alternatives: switching to SMP code [ 96.845570] Booting processor 1/2 APIC 0x1 [ 96.864027] Initializing CPU#1 [ 96.943336] Calibrating delay using timer specific routine.. 4785.43 BogoMIPS (lpj=9570867) [ 96.943343] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 96.943345] CPU: L2 Cache: 1024K (64 bytes/line) [ 96.943348] CPU 1/1 -> Node 1 [ 96.943470] AMD Opteron(tm) Processor 250 stepping 0a [ 96.947334] CPU 1: Syncing TSC to CPU 0. [ 96.947518] CPU 1: synchronized TSC with CPU 0 (last diff -145 cycles, maxerr 1296 cycles) [ 96.947525] Brought up 2 CPUs [ 97.039910] testing NMI watchdog ... OK. [ 97.087760] time.c: Using 1.193182 MHz WALL PIT GTOD PIT/TSC timer. [ 97.100261] time.c: Detected 2392.549 MHz processor. [ 97.239553] migration_cost=745 [ 97.246198] NET: Registered protocol family 16 [ 97.255190] PCI: Using configuration type 1 [ 97.265594] ACPI: Interpreter disabled. [ 97.273448] SCSI subsystem initialized [ 97.280973] usbcore: registered new interface driver usbfs [ 97.291945] usbcore: registered new interface driver hub [ 97.302591] usbcore: registered new device driver usb [ 97.312728] PCI: Probing PCI hardware [ 97.320027] PCI: Probing PCI hardware (bus 00) [ 97.329650] Boot video device is 0000:03:04.0 [ 97.339359] PCI: Using IRQ router default [1022/746b] at 0000:00:07.3 [ 97.352211] PCI->APIC IRQ transform: 0000:01:00.0[D] -> IRQ 19 [ 97.363850] PCI->APIC IRQ transform: 0000:01:00.1[D] -> IRQ 19 [ 97.375489] PCI->APIC IRQ transform: 0000:01:06.0[A] -> IRQ 17 [ 97.387127] PCI->APIC IRQ transform: 0000:03:03.0[A] -> IRQ 28 [ 97.398764] PCI->APIC IRQ transform: 0000:03:04.0[A] -> IRQ 29 [ 97.410411] PCI: Cannot allocate resource region 0 of device 0000:00:0a.1 [ 97.423945] PCI: Cannot allocate resource region 0 of device 0000:00:0b.1 [ 97.437564] PCI-DMA: Disabling AGP. [ 97.444553] PCI-DMA: aperture base @ 4000000 size 65536 KB [ 97.455487] PCI-DMA: using GART IOMMU. [ 97.462975] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 97.476162] PCI: Bridge: 0000:00:06.0 [ 97.483469] IO window: 2000-2fff [ 97.490267] MEM window: e8100000-e81fffff [ 97.498619] PREFETCH window: 88000000-880fffff [ 97.507836] PCI: Bridge: 0000:00:0a.0 [ 97.515147] IO window: disabled. [ 97.521929] MEM window: disabled. [ 97.528898] PREFETCH window: disabled. [ 97.536733] PCI: Bridge: 0000:00:0b.0 [ 97.544047] IO window: 3000-3fff [ 97.550845] MEM window: e8200000-e82fffff [ 97.559197] PREFETCH window: f0000000-f7ffffff [ 97.568507] NET: Registered protocol family 2 [ 97.609825] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 97.624494] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 97.642662] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 97.656781] TCP: Hash tables configured (established 262144 bind 65536) [ 97.669960] TCP reno registered [ 97.676710] microcode: CPU0 not a capable Intel processor [ 97.687492] microcode: CPU1 not a capable Intel processor [ 97.698260] IA-32 Microcode Update Driver: v1.14a [ 97.711884] audit: initializing netlink socket (disabled) [ 97.722661] audit(1159404999.820:1): initialized [ 97.731965] Total HugeTLB memory allocated, 0 [ 97.740993] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 97.753866] NTFS driver 2.1.27 [Flags: R/O]. [ 97.762414] fuse init (API version 7.7) [ 97.770152] JFS: nTxBlock = 8192, nTxLock = 65536 [ 97.782708] io scheduler noop registered [ 97.790555] io scheduler anticipatory registered (default) [ 97.801555] io scheduler deadline registered [ 97.810116] io scheduler cfq registered [ 97.817802] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:00:0a.0 subordinate bus. [ 97.835143] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:00:0b.0 subordinate bus. [ 98.276823] radeonfb (0000:03:04.0): cannot map FB [ 98.286403] radeonfb: probe of 0000:03:04.0 failed with error -5 [ 98.298443] vga16fb: initializing [ 98.305066] vga16fb: mapped to 0xffff8100000a0000 [ 98.445748] Console: switching to colour frame buffer device 80x30 [ 98.465861] fb0: VGA16 VGA frame buffer device [ 98.498130] Real Time Clock Driver v1.12ac [ 98.506345] Non-volatile memory driver v1.2 [ 98.514696] Linux agpgart interface v0.101 (c) Dave Jones [ 98.525481] [drm] Initialized drm 1.0.1 20051102 [ 98.534792] [drm] Initialized radeon 1.25.0 20060524 on minor 0 [ 98.546614] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). [ 98.564465] Hangcheck: Using monotonic_clock(). [ 98.573498] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 98.589297] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 98.602224] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 98.617616] loop: loaded (max 8 devices) [ 98.625445] Intel(R) PRO/1000 Network Driver - version 7.2.7-k2 [ 98.637256] Copyright (c) 1999-2006 Intel Corporation. [ 98.896379] e1000: 0000:03:03.0: e1000_probe: (PCI:66MHz:64-bit) 00:02:b3:9d:d4:d7 [ 98.944078] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 98.957877] Linux video capture interface: v2.00 [ 98.967102] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 98.979771] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 98.995809] AMD8111: IDE controller at PCI slot 0000:00:07.1 [ 99.007102] AMD8111: chipset revision 3 [ 99.014753] AMD8111: not 100% native mode: will probe irqs later [ 99.026727] AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller [ 99.038192] ide0: BM-DMA at 0x1020-0x1027, BIOS settings: hda:pio, hdb:pio [ 99.052671] ide1: BM-DMA at 0x1028-0x102f, BIOS settings: hdc:pio, hdd:pio [ 99.067146] Probing IDE interface ide0... [ 99.644997] Probing IDE interface ide1... [ 100.223891] Probing IDE interface ide0... [ 100.802282] Probing IDE interface ide1... [ 101.381169] libata version 2.00 loaded. [ 101.388912] sata_sil 0000:01:06.0: version 2.0 [ 101.398482] ata1: SATA max UDMA/100 cmd 0xFFFFC200005FE080 ctl 0xFFFFC200005FE08A bmdma 0xFFFFC200005FE000 irq 17 [ 101.418978] ata2: SATA max UDMA/100 cmd 0xFFFFC200005FE0C0 ctl 0xFFFFC200005FE0CA bmdma 0xFFFFC200005FE008 irq 17 [ 101.439440] scsi0 : sata_sil [ 102.031444] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 102.047558] ata1.00: ATA-6, max UDMA/133, 156312576 sectors: LBA48 [ 102.060055] ata1.00: ata1: dev 0 multi count 16 [ 102.073140] ata1.00: configured for UDMA/100 [ 102.081663] scsi1 : sata_sil [ 102.398555] ata2: SATA link down (SStatus 0 SControl 310) [ 102.409385] scsi 0:0:0:0: Direct-Access ATA ST380013AS 3.25 PQ: 0 ANSI: 5 [ 102.425618] SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB) [ 102.438815] sda: Write Protect is off [ 102.446114] sda: Mode Sense: 00 3a 00 00 [ 102.453940] SCSI device sda: drive cache: write back [ 102.463877] SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB) [ 102.477074] sda: Write Protect is off [ 102.484384] sda: Mode Sense: 00 3a 00 00 [ 102.492228] SCSI device sda: drive cache: write back [ 102.502128] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > [ 102.567864] sd 0:0:0:0: Attached scsi disk sda [ 102.576802] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 102.587531] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) [ 102.603768] ohci_hcd 0000:01:00.0: OHCI Host Controller [ 102.614340] ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1 [ 102.629103] ohci_hcd 0000:01:00.0: irq 19, io mem 0xe8100000 [ 102.699885] usb usb1: new device found, idVendor=0000, idProduct=0000 [ 102.712727] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 102.726476] usb usb1: Product: OHCI Host Controller [ 102.736211] usb usb1: Manufacturer: Linux 2.6.18-mm1 ohci_hcd [ 102.747660] usb usb1: SerialNumber: 0000:01:00.0 [ 102.756965] usb usb1: configuration #1 chosen from 1 choice [ 102.768125] hub 1-0:1.0: USB hub found [ 102.775617] hub 1-0:1.0: 3 ports detected [ 102.889686] ohci_hcd 0000:01:00.1: OHCI Host Controller [ 102.900250] ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus number 2 [ 102.915011] ohci_hcd 0000:01:00.1: irq 19, io mem 0xe8101000 [ 102.987213] usb usb2: new device found, idVendor=0000, idProduct=0000 [ 103.000115] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 103.013824] usb usb2: Product: OHCI Host Controller [ 103.023543] usb usb2: Manufacturer: Linux 2.6.18-mm1 ohci_hcd [ 103.034992] usb usb2: SerialNumber: 0000:01:00.1 [ 103.044288] usb usb2: configuration #1 chosen from 1 choice [ 103.055441] hub 2-0:1.0: USB hub found [ 103.062929] hub 2-0:1.0: 3 ports detected [ 103.176811] USB Universal Host Controller Interface driver v3.0 [ 103.188681] sl811: driver sl811-hcd, 19 May 2005 [ 103.197981] Initializing USB Mass Storage driver... [ 103.200674] usb 1-1: new full speed USB device using ohci_hcd and address 2 [ 103.435167] usb 1-1: new device found, idVendor=04b3, idProduct=4001 [ 103.447845] usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 103.461381] usb 1-1: Product: PPC I/F [ 103.468694] usb 1-1: Manufacturer: IBM [ 103.476165] usb 1-1: SerialNumber: 001125913285 [ 103.485284] usb 1-1: configuration #1 chosen from 1 choice [ 103.815216] usb 2-1: new full speed USB device using ohci_hcd and address 2 [ 104.046746] usb 2-1: new device found, idVendor=04b3, idProduct=3006 [ 104.059414] usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0 [ 104.072947] usb 2-1: Product: IBM USB HUB KEYBOARD [ 104.082494] usb 2-1: Manufacturer: Silitek [ 104.090767] usb 2-1: configuration #1 chosen from 1 choice [ 104.106648] hub 2-1:1.0: USB hub found [ 104.115587] hub 2-1:1.0: 3 ports detected [ 104.549493] usb 2-2: new low speed USB device using ohci_hcd and address 3 [ 104.778062] usb 2-2: new device found, idVendor=04b3, idProduct=310c [ 104.790738] usb 2-2: new device strings: Mfr=0, Product=2, SerialNumber=0 [ 104.804273] usb 2-2: Product: USB Optical Mouse [ 104.813473] usb 2-2: configuration #1 chosen from 1 choice [ 105.053427] usb 2-1.1: new full speed USB device using ohci_hcd and address 4 [ 105.188117] usb 2-1.1: new device found, idVendor=04b3, idProduct=3005 [ 105.201132] usb 2-1.1: new device strings: Mfr=1, Product=2, SerialNumber=0 [ 105.215011] usb 2-1.1: Product: IBM USB HUB KEYBOARD [ 105.224969] usb 2-1.1: Manufacturer: Silitek [ 105.233569] usb 2-1.1: configuration #1 chosen from 1 choice [ 105.258958] usbcore: registered new interface driver usb-storage [ 105.270946] USB Mass Storage support registered. [ 105.280186] usbcore: registered new interface driver hiddev [ 105.298957] input: IBM PPC I/F as /class/input/input0 [ 105.309051] input: USB HID v1.10 Keyboard [IBM PPC I/F] on usb-0000:01:00.0-1 [ 105.333883] input: IBM PPC I/F as /class/input/input1 [ 105.343960] input: USB HID v1.10 Mouse [IBM PPC I/F] on usb-0000:01:00.0-1 [ 105.362806] input: USB Optical Mouse as /class/input/input2 [ 105.373928] input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:01:00.1-2 [ 105.393753] input: Silitek IBM USB HUB KEYBOARD as /class/input/input3 [ 105.406823] input: USB HID v1.10 Keyboard [Silitek IBM USB HUB KEYBOARD] on usb-0000:01:00.1-1.1 [ 105.424416] usbcore: registered new interface driver usbhid [ 105.435522] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 105.449738] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 105.459880] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 105.469921] mice: PS/2 mouse device common for all mice [ 105.480822] oprofile: using NMI interrupt. [ 105.489022] Netfilter messages via NETLINK v0.30. [ 105.498417] ip_conntrack version 2.4 (8192 buckets, 65536 max) - 272 bytes per conntrack [ 105.619007] ctnetlink v0.90: registering with nfnetlink. [ 105.629611] ip_conntrack_pptp version 3.1 loaded [ 105.638842] TCP bic registered [ 105.644954] NET: Registered protocol family 1 [ 105.653649] NET: Registered protocol family 17 [ 105.662516] NET: Registered protocol family 15 [ 105.904813] kjournald starting. Commit interval 5 seconds [ 105.915754] EXT3-fs: mounted filesystem with ordered data mode. [ 105.927586] VFS: Mounted root (ext3 filesystem) readonly. [ 105.938425] Freeing unused kernel memory: 316k freed [ 107.794446] warning: process `ls' used the removed sysctl system call [ 108.879759] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex [ 108.956672] warning: process `touch' used the removed sysctl system call [ 109.291388] EXT3 FS on sda1, internal journal [ 109.318904] warning: process `touch' used the removed sysctl system call [ 109.382769] warning: process `touch' used the removed sysctl system call [ 109.579204] warning: process `evms_activate' used the removed sysctl system call [ 110.689106] Adding 9783544k swap on /dev/sda8. Priority:-1 extents:1 across:9783544k [ 468.252583] device eth0 entered promiscuous mode [ 468.261805] audit(1159405373.265:2): dev=eth0 prom=256 old_prom=0 auid=4294967295 [ 527.250201] device eth0 left promiscuous mode [ 527.261023] audit(1159405432.384:3): dev=eth0 prom=0 old_prom=256 auid=4294967295