Linux version 2.6.18-mm2-hrt-dyntick5 (valdis@turing-police.cc.vt.edu) (gcc version 4.1.1 20060926 (Red Hat 4.1.1-26)) #1 PREEMPT Mon Oct 2 02:41:10 EDT 2006 BIOS-provided physical RAM map: sanitize start sanitize end copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2 copy_e820_map() start: 0000000000100000 size: 000000002fee2800 end: 000000002ffe2800 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000002ffe2800 size: 000000000001d800 end: 0000000030000000 type: 2 copy_e820_map() start: 00000000feda0000 size: 0000000000060000 end: 00000000fee00000 type: 2 copy_e820_map() start: 00000000ffb80000 size: 0000000000480000 end: 0000000100000000 type: 2 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 0000000000100000 - 000000002ffe2800 (usable) BIOS-e820: 000000002ffe2800 - 0000000030000000 (reserved) BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved) BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) 767MB LOWMEM available. Entering add_active_range(0, 0, 196578) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 196578 early_node_map[1] active PFN ranges 0: 0 -> 196578 On node 0 totalpages: 196578 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1503 pages used for memmap Normal zone: 190979 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 DELL ) @ 0x000fde50 ACPI: RSDT (v001 DELL CPi R 0x27d40107 ASL 0x00000061) @ 0x000fde64 ACPI: FADT (v001 DELL CPi R 0x27d40107 ASL 0x00000061) @ 0x000fde90 ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 Allocating PCI resources starting at 40000000 (gap: 30000000:ceda0000) Detected 1595.398 MHz processor. Built 1 zonelists. Total pages: 195043 Kernel command line: vga=794 quiet crashkernel=64M@16M single Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (05603000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 Clock event device pit configured with caps set: 07 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 706888k/786312k available (2412k kernel code, 78852k reserved, 1044k data, 180k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffb7000 - 0xfffff000 ( 288 kB) vmalloc : 0xf0800000 - 0xfffb5000 ( 247 MB) lowmem : 0xc0000000 - 0xeffe2000 ( 767 MB) .init : 0xc04e8000 - 0xc0515000 ( 180 kB) .data : 0xc035b03f - 0xc0460128 (1044 kB) .text : 0xc0100000 - 0xc035b03f (2412 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3192.28 BogoMIPS (lpj=1596144) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: 3febf9ff 00000000 00000000 00000080 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.60GHz stepping 04 Checking 'hlt' instruction... OK. ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0800) checking if image is initramfs... it is Freeing initrd memory: 1824k freed NET: Registered protocol family 16 ACPI: ACPI Dock Station Driver ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfbfee, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0880-08bf claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11 ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] ACPI: Power Resource [PADA] (on) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices Intel 82802 RNG detected SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:02: ioport range 0x800-0x805 could not be reserved pnp: 00:02: ioport range 0x808-0x80f could not be reserved pnp: 00:03: ioport range 0x806-0x807 has been reserved pnp: 00:03: ioport range 0x810-0x85f could not be reserved pnp: 00:03: ioport range 0x860-0x87f has been reserved pnp: 00:03: ioport range 0x880-0x8bf has been reserved pnp: 00:03: ioport range 0x8c0-0x8df has been reserved pnp: 00:03: ioport range 0x8e0-0x8ff has been reserved pnp: 00:08: ioport range 0x900-0x91f has been reserved pnp: 00:08: ioport range 0x3f0-0x3f1 has been reserved PCI: Bridge: 0000:00:01.0 IO window: c000-cfff MEM window: fc000000-fdffffff PREFETCH window: d8000000-e7ffffff PCI: Bus 3, cardbus bridge: 0000:02:01.0 IO window: 0000e000-0000e0ff IO window: 0000e400-0000e4ff PREFETCH window: 40000000-41ffffff MEM window: f4000000-f5ffffff PCI: Bus 7, cardbus bridge: 0000:02:01.1 IO window: 0000e800-0000e8ff IO window: 0000f000-0000f0ff PREFETCH window: 42000000-43ffffff MEM window: f6000000-f7ffffff PCI: Bus 11, cardbus bridge: 0000:02:03.0 IO window: 0000f400-0000f4ff IO window: 0000f800-0000f8ff PREFETCH window: 44000000-45ffffff MEM window: fa000000-fbffffff PCI: Bridge: 0000:00:1e.0 IO window: e000-ffff MEM window: f4000000-fbffffff PREFETCH window: 40000000-46ffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:02:01.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Enabling device 0000:02:01.1 (0000 -> 0003) ACPI: PCI Interrupt 0000:02:01.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. speedstep: frequency transition measured seems out of range (0 nSec), falling back to a safe one of 500000 nSec. audit: initializing netlink socket (disabled) audit(1159802531.385:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered vesafb: framebuffer at 0xe0000000, mapped to 0xf0880000, using 5120k, total 32768k vesafb: mode is 1280x1024x16, linelength=2560, pages=1 vesafb: protected mode interface info at c000:e140 vesafb: pmi: set display start = c00ce185, set palette = c00ce20a vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device ACPI: Video Device [VID] (multi-head: yes rom: no post: no) Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using get_cycles(). Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI interrupt for device 0000:00:1f.6 disabled RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize loop: loaded (max 8 devices) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:02:00.0: 3Com PCI 3c905C Tornado at f0804c00. ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 0000:02:08.0: 3Com PCI 3c905C Tornado at f0806800. libata version 2.00 loaded. ata_piix 0000:00:1f.1: version 2.00ac7 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1f.1 to 64 ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xBFA0 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xBFA8 irq 15 scsi0 : ata_piix ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.18-mm2-hrt-dyntick5 uhci_hcd usb usb1: SerialNumber: 0000:00:1d.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40 usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.18-mm2-hrt-dyntick5 uhci_hcd usb usb2: SerialNumber: 0000:00:1d.1 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20 usb usb3: new device found, idVendor=0000, idProduct=0000 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.18-mm2-hrt-dyntick5 uhci_hcd usb usb3: SerialNumber: 0000:00:1d.2 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 input: AT Translated Set 2 keyboard as /class/input/input1 ata1.00: ATA-6, max UDMA/100, 117210240 sectors: LBA ata1.00: ata1: dev 0 multi count 8 ata1.01: ATAPI, max UDMA/33 ata1.00: configured for UDMA/100 usb 2-2: new low speed USB device using uhci_hcd and address 2 ata1.01: configured for UDMA/33 scsi1 : ata_piix usb 2-2: new device found, idVendor=045e, idProduct=0023 usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: Microsoft Trackball OpticalŪ usb 2-2: Manufacturer: Microsoft usb 2-2: configuration #1 chosen from 1 choice input: Microsoft Microsoft Trackball OpticalŪ as /class/input/input2 input: USB HID v1.00 Mouse [Microsoft Microsoft Trackball OpticalŪ] on usb-0000:00:1d.1-2 input: DualPoint Stick as /class/input/input3 input: AlpsPS/2 ALPS DualPoint TouchPad as /class/input/input4 scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2060A 0000 PQ: 0 ANSI: 5 SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda:<6>i2c /dev entries driver device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com EDAC MC: Ver: 2.0.1 Oct 2 2006 Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC). ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1f.5 to 64 ALSA device list: No soundcards found. TCP bic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Using IPI Shortcut mode Time: tsc clocksource has been installed. Clock event device pit configured with caps set: 08 Switched to high resolution mode on CPU 0 Freeing unused kernel memory: 180k freed Write protecting the kernel read-only data: 434k sda1 sda2 sd 0:0:0:0: Attached scsi disk sda scsi 0:0:1:0: CD-ROM TOSHIBA CDRW/DVD SDR2102 1D13 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 0:0:1:0: Attached scsi CD-ROM sr0 intel8x0_measure_ac97_clock: measured 51386 usecs intel8x0: clocking to 48000 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. security: 6 users, 5 roles, 2013 types, 80 bools, 1 sens, 1024 cats security: 58 classes, 111120 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev dm-0, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts audit(1159802536.642:2): policy loaded auid=4294967295 audit(1159802537.006:3): avc: denied { execute } for pid=457 comm="rc.sysinit" name="hostname" dev=dm-0 ino=33031 scontext=system_u:system_r:initrc_t:s0 tcontext=system_u:object_r:hostname_exec_t:s0 tclass=file audit(1159802537.006:4): avc: denied { execute_no_trans } for pid=457 comm="rc.sysinit" name="hostname" dev=dm-0 ino=33031 scontext=system_u:system_r:initrc_t:s0 tcontext=system_u:object_r:hostname_exec_t:s0 tclass=file audit(1159802537.006:5): avc: denied { read } for pid=457 comm="rc.sysinit" name="hostname" dev=dm-0 ino=33031 scontext=system_u:system_r:initrc_t:s0 tcontext=system_u:object_r:hostname_exec_t:s0 tclass=file Real Time Clock Driver v1.12ac audit(1159802539.162:6): avc: denied { dac_override } for pid=487 comm="dmesg" capability=1 scontext=system_u:system_r:dmesg_t:s0 tcontext=system_u:system_r:dmesg_t:s0 tclass=capability audit(1159802540.991:7): avc: denied { dac_override } for pid=542 comm="pam_console_app" capability=1 scontext=system_u:system_r:pam_console_t:s0-s0:c0.c1023 tcontext=system_u:system_r:pam_console_t:s0-s0:c0.c1023 tclass=capability ACPI: PCI Interrupt 0000:02:01.2[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[f8fff000-f8fff7ff] Max Packet=[2048] IR/IT contexts=[4/4] Yenta: CardBus bridge found at 0000:02:01.0 [1028:00d5] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:01.0, mfunc 0x05033002, devctl 0x64 Yenta: CardBus bridge found at 0000:02:01.1 [1028:00d5] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:01.1, mfunc 0x05033002, devctl 0x64 Yenta: CardBus bridge found at 0000:02:03.0 [12a3:ab01] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:03.0, mfunc 0x01000002, devctl 0x60 Linux agpgart interface v0.101 (c) Dave Jones iTCO_wdt: Intel TCO WatchDog Timer Driver v1.00 (30-Jul-2006) iTCO_wdt: Found a ICH3-M TCO device (Version=1, TCOBASE=0x0860) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) agpgart: Detected an Intel i845 Chipset. agpgart: AGP aperture is 64M @ 0xe8000000 ohci1394: fw-host0: Running dma failed because Node ID is not valid Yenta: ISA IRQ mask 0x0498, PCI irq 11 Socket status: 30000020 pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff cs: IO port probe 0xe000-0xffff: clean. pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x46ffffff Yenta: ISA IRQ mask 0x0498, PCI irq 11 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff cs: IO port probe 0xe000-0xffff: clean. pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x46ffffff Yenta: ISA IRQ mask 0x0000, PCI irq 11 Socket status: 30000010 pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff cs: IO port probe 0xe000-0xffff: clean. pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x46ffffff pccard: CardBus card inserted into slot 0 PCI: Enabling device 0000:03:00.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:03:00.0 to 64 eth2: Xircom cardbus revision 3 at irq 11 PCI: Enabling device 0000:03:00.1 (0000 -> 0003) ACPI: PCI Interrupt 0000:03:00.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 0000:03:00.1: ttyS1 at I/O 0xe080 (irq = 11) is a 16550A ohci1394: fw-host0: AT dma reset ctx=0, aborting transmission ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting... pccard: PCMCIA card inserted into slot 2 ieee1394: Host added: ID:BUS[0-00:1023] GUID[374fc0002a71c021] cs: IO port probe 0x100-0x3af: excluding 0x370-0x37f cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. cs: IO port probe 0x100-0x3af: excluding 0x370-0x37f cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. cs: memory probe 0xf4000000-0xfbffffff: excluding 0xf4000000-0xf8ffffff 0xfa000000-0xfbffffff pcmcia: registering new device pcmcia2.0 cs: IO port probe 0x100-0x3af: excluding 0x370-0x37f cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. orinoco 0.15 (David Gibson , Pavel Roskin , et al) orinoco_cs 0.15 (David Gibson , Pavel Roskin , et al) pcmcia: request for exclusive IRQ could not be fulfilled. pcmcia: the driver needs updating to supported shared IRQ lines. eth2: Hardware identity 0005:0004:0005:0000 eth2: Station identity 001f:0001:0008:000a eth2: Firmware determined as Lucent/Agere 8.10 eth2: Ad-hoc demo mode supported eth2: IEEE standard IBSS ad-hoc mode supported eth2: WEP supported, 104-bit key eth2: MAC address 00:02:2D:5C:11:48 eth2: Station name "HERMES I" eth2: ready eth2: orinoco_cs at 2.0, irq 11, io 0xe100-0xe13f Non-volatile memory driver v1.2 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Dell laptop SMM driver v1.14 21/02/2005 Massimo Dal Zotto (dz@debian.org) Netfilter messages via NETLINK v0.30. audit(1159802546.388:8): avc: denied { getattr } for pid=456 comm="rc.sysinit" name="hostname" dev=dm-0 ino=33031 scontext=system_u:system_r:initrc_t:s0 tcontext=system_u:object_r:hostname_exec_t:s0 tclass=file ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery absent) ACPI: Battery Slot [BAT1] (battery absent) ACPI: Lid Switch [LID] ACPI: Power Button (CM) [PBTN] ACPI: Sleep Button (CM) [SBTN] Using specific hotkey driver ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THM] (68 C) EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda1, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs kjournald starting. Commit interval 5 seconds EXT3 FS on dm-11, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-11, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-7, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-8, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-9, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3 FS on dm-10, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-10, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-6, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3 FS on dm-4, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-4, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-5, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-1, type ext3), uses xattr Adding 1572856k swap on /dev/rootvg/swap. Priority:-1 extents:1 across:1572856k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts audit(1159802586.630:9): avc: denied { getattr } for pid=1502 comm="bash" name="spamassassin" dev=dm-0 ino=197880 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:initrc_exec_t:s0 tclass=file audit(1159802586.630:10): avc: denied { execute } for pid=1502 comm="bash" name="spamassassin" dev=dm-0 ino=197880 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:initrc_exec_t:s0 tclass=file audit(1159802586.630:11): avc: denied { read } for pid=1502 comm="bash" name="spamassassin" dev=dm-0 ino=197880 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:initrc_exec_t:s0 tclass=file audit(1159802592.469:12): avc: denied { execute_no_trans } for pid=1525 comm="bash" name="cpuspeed" dev=dm-0 ino=197100 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:initrc_exec_t:s0 tclass=file audit(1159802592.506:13): avc: denied { ioctl } for pid=1525 comm="cpuspeed" name="cpuspeed" dev=dm-0 ino=197100 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:initrc_exec_t:s0 tclass=file audit(1159802592.551:14): avc: denied { getattr } for pid=1525 comm="cpuspeed" name="cpuspeed" dev=dm-7 ino=295240 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:cpuspeed_exec_t:s0 tclass=file audit(1159802592.585:15): avc: denied { execute } for pid=1529 comm="bash" name="cpuspeed" dev=dm-7 ino=295240 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:cpuspeed_exec_t:s0 tclass=file audit(1159802592.585:16): avc: denied { read } for pid=1529 comm="bash" name="cpuspeed" dev=dm-7 ino=295240 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:cpuspeed_exec_t:s0 tclass=file audit(1159802592.586:17): avc: denied { execute_no_trans } for pid=1530 comm="bash" name="cpuspeed" dev=dm-7 ino=295240 scontext=system_u:system_r:sysadm_t:s0 tcontext=system_u:object_r:cpuspeed_exec_t:s0 tclass=file