Linux version 2.6.17.6 (root@nova) (gcc version 4.1.1 (Gentoo 4.1.1)) #1 SMP PREEMPT Thu Oct 5 01:41:48 CEST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fe80000 (usable)
 BIOS-e820: 000000007fe80000 - 000000007ff00000 (ACPI NVS)
 BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
 BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
1150MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f65b0
On node 0 totalpages: 523904
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 294528 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6580
ACPI: RSDT (v001 PTLTD  Capell00 0x06040000  LTP 0x00000000) @ 0x7fe8be4b
ACPI: FADT (v001 HP     NISSAN   0x06040000 LOHR 0x0000005a) @ 0x7fe92dee
ACPI: MADT (v001 HP     NISSAN   0x06040000 LOHR 0x0000005a) @ 0x7fe92e62
ACPI: HPET (v001 HP     NISSAN   0x06040000 LOHR 0x0000005a) @ 0x7fe92eca
ACPI: MCFG (v001 HP     NISSAN   0x06040000 LOHR 0x0000005a) @ 0x7fe92f02
ACPI: BOOT (v001 PTLTD  $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x7fe92fd8
ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @ 0x7fe92f70
ACPI: SSDT (v001 SataRe SataAhci 0x00001000 INTL 0x20060217) @ 0x7fe8c85f
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20060217) @ 0x7fe8be8f
ACPI: DSDT (v001 HP     NISSAN   0x06040000 INTL 0x20060217) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: 2 duplicate APIC table ignored.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
Built 1 zonelists
Kernel command line: root=/dev/sda6
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2071860k/2095616k available (3626k kernel code, 22524k reserved, 1084k data, 216k init, 1178112k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Using HPET for base-timer
Using HPET for gettimeofday
Detected 1729.065 MHz processor.
Using hpet for high-res timesource
Calibrating delay using timer specific routine.. 3463.06 BogoMIPS (lpj=6926136)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 20k freed
CPU0: Intel Genuine Intel(R) CPU           T2250  @ 1.73GHz stepping 08
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3458.27 BogoMIPS (lpj=6916553)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU           T2250  @ 1.73GHz stepping 08
Total of 2 processors activated (6921.34 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=8000
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #09 (-#0c) is hidden behind transparent bridge #08 (-#09) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 *6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: Embedded Controller [EC0] (gpe 25) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.2
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.2
PCI: Cannot allocate resource region 0 of device 0000:06:00.0
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: d0000000-d1ffffff
  PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
  IO window: disabled.
  MEM window: 8a000000-8a0fffff
  PREFETCH window: disabled.
PCI: Bus 9, cardbus bridge: 0000:08:06.0
  IO window: 00002400-000024ff
  IO window: 00002800-000028ff
  PREFETCH window: 88000000-89ffffff
  MEM window: 8c000000-8dffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 2000-2fff
  MEM window: d2000000-d20fffff
  PREFETCH window: 88000000-89ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Enabling device 0000:00:1c.2 (0100 -> 0102)
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:08:06.0[A] -> GSI 18 (level, low) -> IRQ 185
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/W].
SGI XFS with ACLs, security attributes, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
Real Time Clock Driver v1.12ac
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[B] -> GSI 19 (level, low) -> IRQ 233
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
ahci 0000:00:1f.2: version 1.2
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part 
ata1: SATA max UDMA/133 cmd 0xF8826500 ctl 0x0 bmdma 0x0 irq 50
ata2: SATA max UDMA/133 cmd 0xF8826580 ctl 0x0 bmdma 0x0 irq 50
ata3: SATA max UDMA/133 cmd 0xF8826600 ctl 0x0 bmdma 0x0 irq 50
ata4: SATA max UDMA/133 cmd 0xF8826680 ctl 0x0 bmdma 0x0 irq 50
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:306b 83:7c09 84:6023 85:3069 86:3c09 87:6023 88:203f
ata1: dev 0 ATA-7, max UDMA/100, 234441648 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : ahci
ata2: SATA link down (SStatus 0)
scsi1 : ahci
ata3: SATA link down (SStatus 0)
scsi2 : ahci
ata4: SATA link down (SStatus 0)
scsi3 : ahci
  Vendor: ATA       Model: FUJITSU MHV2120B  Rev: 892C
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
sd 0:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt 0000:08:06.1[B] -> GSI 19 (level, low) -> IRQ 233
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[233]  MMIO=[d2007000-d20077ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
video1394: Installed video1394 module
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 58, io mem 0xd2404000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 58, io base 0x00001800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 233, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 169, io base 0x00001860
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 3-2: new low speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input1
input: AT Translated Set 2 keyboard as /class/input/input2
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC).
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input3
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA device list:
  #0: HDA Intel at 0xd2400000 irq 66
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
UDF-fs: No VRS found
XFS mounting filesystem sda6
Starting XFS recovery on filesystem: sda6 (logdev: internal)
Ending XFS recovery on filesystem: sda6 (logdev: internal)
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 216k freed
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-8774  Tue Aug  1 20:54:08 PDT 2006
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, 1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.1.0mpr
ipw3945: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:06:00.0 to 64
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:08:08.0[A] -> GSI 20 (level, low) -> IRQ 74
e100: eth0: e100_probe: addr 0xd2006000, irq 74, MAC addr 00:16:D4:3E:C9:90
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'TKIP'
ieee80211_crypt: registered algorithm 'CCMP'
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI Error (evxfevnt-0189): Could not enable SleepButton event [20060127]
ACPI Warning (evxface-0147): Could not enable fixed event 3 [20060127]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ01] (49 C)
ACPI: Thermal Zone [TZ02] (0 C)
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
XFS mounting filesystem sda7
Ending clean XFS mount for filesystem: sda7
XFS mounting filesystem sda8
Ending clean XFS mount for filesystem: sda8
XFS mounting filesystem sda9
Starting XFS recovery on filesystem: sda9 (logdev: internal)
Ending XFS recovery on filesystem: sda9 (logdev: internal)
XFS mounting filesystem sda10
Starting XFS recovery on filesystem: sda10 (logdev: internal)
Ending XFS recovery on filesystem: sda10 (logdev: internal)
XFS mounting filesystem sda11
Starting XFS recovery on filesystem: sda11 (logdev: internal)
Ending XFS recovery on filesystem: sda11 (logdev: internal)
Adding 4000144k swap on /dev/sda5.  Priority:-1 extents:1 across:4000144k
ipw3945: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
device eth1 entered promiscuous mode
ipw3945: Error sending cmd #08 to daemon: time out after 500ms.
device eth1 left promiscuous mode
ipw3945: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
ipw3945: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
ipw3945: association process canceled
ipw3945: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
ipw3945: association process canceled
ipw3945: association process canceled
ipw3945: association process canceled
ipw3945: association process canceled
ipw3945: association process canceled
ipw3945: association process canceled