| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <Pine.SOC.4.61.0610201751150.596@math.ut.ee> Date: Fri, 20 Oct 2006 18:03:53 +0300 (EEST) From: Meelis Roos <mroos@...ux.ee> To: Linux Kernel list <linux-kernel@...r.kernel.org> Subject: PCI cache line not set - how to set? I use sii3112 in Motorola Powerstack II computer with 300 Mhz PowerPC 604r CPU (should use 32-byte cache line size). However, its firmware is OF based and seems to literally ignore non-OF PCI cards like the sii3112. Linux still sees the cards and I can use them, but... sata_sil 0000:00:07.0: cache line size not set. Driver may not function and a new SATA disk that is 70+ MB/s in a PC yields only 10 MB/s here. So a wild guess that either PCI latency (set to 0) or PCI cache line size need to be set. setpci -s 00:07.0 CACHE_LINE_SIZE 00 so I do setpci -s 00:07.0 CACHE_LINE_SIZE=08 and I can read 08 back - fine. But reloading sata_sil still tells that cache line size not set. sata_sil uses sil_get_device_cache_line() to read the cache line size and that does a simple pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &cache_line); So should this setpci work? Setpci PCI_LATENCY works and gives measurable bad results. Setting latency timer to 32 (20 hex) drops the performance even more (to 3.5-3.7 MB/s) so I reset it to 0. NCR 53C825 SCSI with 36G 10Krpm disk also gives 10 MB/s, cache line size 08, latency timer 00. Where to look next? lspci -vvvxxx is here: 00:00.0 Host bridge: IBM 82660 CPU to PCI Bridge (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 14 10 37 00 06 01 00 02 02 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 20 40 60 00 00 80 a0 00 00 00 00 00 00 00 00 90: 1f 3f 5f 7f 00 00 9f bf 00 00 00 00 00 00 00 00 a0: cf 15 8a 00 66 44 00 44 00 00 00 00 00 00 00 00 b0: 00 43 00 00 07 00 52 00 00 00 07 4f 00 00 00 00 c0: 2c 00 00 40 11 00 00 06 f8 0c 00 80 1f 30 00 01 d0: f8 01 f8 01 05 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:01.0 ISA bridge: Symphony Labs W83C553 (rev 10) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: ad 10 65 05 07 00 00 02 10 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 20 04 00 ef fb ab 78 00 01 00 00 00 00 33 44 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 09 0a 0b 0e 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: e0 01 00 80 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 97 01 01 01 00 00 00 00 00 00 00 00 00 00 00:01.1 IDE interface: Symphony Labs SL82c105 (rev 05) (prog-if 8f [Master SecP SecO PriP PriO]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 0 Region 0: I/O ports at 800001f0 [disabled] [size=8] Region 1: I/O ports at 800003f4 [disabled] [size=4] Region 2: I/O ports at 80000170 [disabled] [size=8] Region 3: I/O ports at 80000374 [disabled] [size=4] Region 4: I/O ports at 80000000 [disabled] [size=16] Region 5: I/O ports at 800010b0 [disabled] [size=16] 00: ad 10 05 01 00 00 80 02 05 8f 01 01 08 00 80 00 10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00 20: 01 00 00 00 b1 10 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 02 28 40: 91 00 ff 00 09 09 00 00 09 09 00 00 09 09 00 00 50: 09 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.0 SCSI storage controller: LSI Logic / Symbios Logic 53c825 (rev 13) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (4250ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 15 Region 0: I/O ports at 80001400 [size=256] Region 1: Memory at c4008000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at c4009000 (32-bit, non-prefetchable) [size=4K] 00: 00 10 03 00 17 00 00 02 13 00 00 01 08 00 00 00 10: 01 14 00 00 00 80 00 04 00 90 00 04 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 11 40 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: da 00 00 1b 47 08 00 0f 00 08 80 00 80 00 0f 0a 90: ff 00 69 80 00 ff ff ff 00 f0 35 31 a0 93 00 04 a0: 00 08 24 00 00 00 00 50 b8 93 00 04 c0 93 00 04 b0: 00 90 00 04 d0 12 69 80 46 6d 00 81 c0 23 01 04 c0: 8f 05 00 00 b3 00 60 0f 0c 00 80 00 76 00 00 80 d0: 00 00 00 80 00 00 00 80 00 00 00 80 00 84 00 00 e0: 99 25 18 ac f9 5e ff f9 69 22 28 00 f4 76 f3 bc f0: 80 10 4d 41 7f cf 9b f6 04 8e 06 20 fa 9b be bb 00:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (5000ns min, 10000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 80001800 [size=128] Region 1: Memory at c400a000 (32-bit, non-prefetchable) [size=128] Expansion ROM at c1040000 [disabled] [size=256K] 00: 11 10 09 00 17 00 80 02 22 00 00 02 08 00 00 00 10: 01 18 00 00 00 a0 00 04 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 04 01 00 00 00 00 00 00 00 00 0b 01 14 28 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:06.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (5000ns min, 10000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 80001000 [size=128] Region 1: Memory at c2000000 (32-bit, non-prefetchable) [size=128] Expansion ROM at c1040000 [disabled] [size=256K] 00: 11 10 09 00 17 00 80 02 22 00 00 02 08 00 00 00 10: 01 10 00 00 00 00 00 02 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 04 01 00 00 00 00 00 00 00 00 0a 01 14 28 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:07.0 Mass storage controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02) Subsystem: Silicon Image, Inc. SiI 3112 SATALink Controller Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 80001080 [size=8] Region 1: I/O ports at 80001088 [size=4] Region 2: I/O ports at 80001090 [size=8] Region 3: I/O ports at 80001098 [size=4] Region 4: I/O ports at 800010a0 [size=16] Region 5: Memory at c2000200 (32-bit, non-prefetchable) [size=512] Expansion ROM at c1080000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 00: 95 10 12 31 03 00 b0 02 02 00 80 01 08 00 00 00 10: 81 10 00 00 89 10 00 00 91 10 00 00 99 10 00 00 20: a1 10 00 00 00 02 00 02 00 00 00 00 95 10 12 31 30: 00 00 08 01 60 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 41 00 04 28 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 00 22 06 00 40 00 64 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 08 00 00 00 00 80 9d 80 80: 22 00 00 00 03 00 00 00 00 00 c0 00 ec cc de 96 90: 00 00 00 0c 12 31 00 80 00 00 00 18 00 00 00 00 a0: 01 01 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40 b0: 01 01 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:08.0 VGA compatible controller: Cirrus Logic GD 5446 (rev 45) (prog-if 00 [VGA]) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 15 Region 0: Memory at c0000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at c2001000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at c4000000 [disabled] [size=32K] 00: 13 10 b8 00 03 00 00 02 45 00 00 03 00 00 00 00 10: 08 00 00 00 00 10 00 02 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 04 00 00 00 00 00 00 00 00 0f 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 -- Meelis Roos (mroos@...ux.ee) - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists