linux-kernel - Re: splice/vmsplice performance test results

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20061116202529.GH7164@kernel.dk>
Date:	Thu, 16 Nov 2006 21:25:29 +0100
From:	Jens Axboe <jens.axboe@...cle.com>
To:	Jim Schutt <jaschut@...dia.gov>
Cc:	linux-kernel@...r.kernel.org
Subject: Re: splice/vmsplice performance test results

On Thu, Nov 16 2006, Jim Schutt wrote:
> Hi,
> 
> I've done some testing to see how splice/vmsplice perform
> vs. other alternatives on transferring a large file across
> a fast network.  One option I tested was to use vmsplice 
> to get a 1-copy receive, but it didn't perform as well 
> as I had hoped.  I was wondering if my results were at odds
> with what other people have observed.
> 
> I've two systems, each with:
>   Tyan S2895 motherboard
>   2 ea. 2.6 GHz Opteron
>   1 GiB memory
>   Myricom Myri-10G 10 Gb/s NIC (PCIe x8)
>   2.6.19-rc5-g134a11f0 on FC4
> 
> In addition, one system has a 3ware 9590-8ML (PCIe) and a 3ware
> 9550SX-8LP (PCI-X), with 16 Seagate Barracuda 7200.10 SATA drives 
> (250 GB ea., NCQ enabled).  Write caching is enabled on the 3ware
> cards.
> 
> The Myricom cards are connected back-to-back using 9000 byte MTU. 
> I baseline the network performance with 'iperf -w 1M -l 64K'
> and get 6.9 Gb/s.
> 
> After a fair amount of testing, I settled on a 4-way software
> RAID0 on top of 4-way hardware RAID0 units as giving the best
> streaming performance.  The file system is XFS, with the stripe
> unit set to the hardware RAID chunk size, and the stripe width 
> 16 times that.  
> 
> Disk tuning parameters in /sys/block/sd*/queue are default
> values, except queue/nr_requests = 5 gives me best performance.
> (It seems like the 3ware cards slow down a little if I feed them 
> too much data on the streaming write test I'm using.)
> 
> I baseline file write performance with 
>   sync; time { dd if=/dev/zero of=./zero bs=32k count=512k; sync; }
> and get 465-520 MB/s (highly variable).
> 
> I test baseline file read performance with
>   time dd if=./zero of=/dev/null bs=32k count=512k
> and get 950 MB/s (fairly repeatable).
> 
> My test program can do one of the following:
> 
> send data:
>  A) read() from file into buffer, write() buffer into socket
>  B) mmap() section of file, write() that into socket, munmap()
>  C) splice() from file to pipe, splice() from pipe to socket
> 
> receive data:
>  1) read() from socket into buffer, write() buffer into file
>  2) ftruncate() to extend file, mmap() new extent, read() 
>       from socket into new extent, munmap()
>  3) read() from socket into buffer, vmsplice() buffer to 
>      pipe, splice() pipe to file (using the double-buffer trick)
> 
> Here's the results, using:
>  - 64 KiB buffer, mmap extent, or splice
>  - 1 MiB TCP window
>  - 16 GiB data sent across network
> 
> A) from /dev/zero -> 1) to /dev/null : 857 MB/s (6.86 Gb/s)
> 
> A) from file      -> 1) to /dev/null : 472 MB/s (3.77 Gb/s)
> B) from file      -> 1) to /dev/null : 366 MB/s (2.93 Gb/s)
> C) from file      -> 1) to /dev/null : 854 MB/s (6.83 Gb/s)
> 
> A) from /dev/zero -> 1) to file      : 375 MB/s (3.00 Gb/s)
> A) from /dev/zero -> 2) to file      : 150 MB/s (1.20 Gb/s)
> A) from /dev/zero -> 3) to file      : 286 MB/s (2.29 Gb/s)
> 
> I had (naively) hoped the read/vmsplice/splice combination would 
> run at the same speed I can write a file, i.e. at about 450 MB/s
> on my setup.  Do any of my numbers seem bogus, so I should look 
> harder at my test program?

Could be read-ahead playing in here, I'd have to take a closer look at
the generated io patterns to say more about that. Any chance you can
capture iostat or blktrace info for such a run to compare that goes to
the disk? Can you pass along the test program?

> Or is read+write really the fastest way to get data off a
> socket and into a file?

splice() should be just as fast of course, and more efficient. Not a lot
of real-life performance tuning has gone into it yet, so I would not be
surprised if we need to smoothen a few edges.

-- 
Jens Axboe

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/