| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <200611300803.30969.edt@aei.ca> Date: Thu, 30 Nov 2006 08:03:30 -0500 From: Ed Tomlinson <edt@....ca> To: Randy Dunlap <randy.dunlap@...cle.com> Cc: Andrew Morton <akpm@...l.org>, linux-kernel@...r.kernel.org Subject: Re: 2.6.19-rc6-mm2 On Wednesday 29 November 2006 23:10, Randy Dunlap wrote: > On Wed, 29 Nov 2006 22:42:20 -0500 Ed Tomlinson wrote: > > > On Tuesday 28 November 2006 05:02, Andrew Morton wrote: > > > > > Will appear eventually at > > > > > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.19-rc6/2.6.19-rc6-mm2/ > > > > This kernel does not boot here. It does not get far enough to post anything to my serial console. > > Have you tried using "earlyprintk=..." to see if it produces any > more output? Nothing is displayed by earlyprintk. I also added it to the rc5-mm2 boot to verify it. The messages displayed were the same as below... Thanks Ed > > The last booted kernel here is 19-rc5-mm2. Grub is used to boot, here is the starting log > > of rc5-mm2 build is UP AMD64: > > > > [ 0.000000] Linux version 2.6.19-rc5-mm2 (root@...ver) (gcc version 4.1.1 (Gentoo 4.1.1-r1)) #1 PREEM6 > > [ 0.000000] Command line: root=/dev/sda3 vga=0x318 video=vesafb:ywrap,mtrr:3 console=tty0 console=tty1 > > [ 0.000000] BIOS-provided physical RAM map: > > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > > [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > > [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > > [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) > > [ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) > > [ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) > > [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > > [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) > > [ 0.000000] BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved) > > [ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > > [ 0.000000] end_pfn_map = 1048576 > > [ 0.000000] DMI 2.2 present. > > [ 0.000000] Zone PFN ranges: > > [ 0.000000] DMA 0 -> 4096 > > [ 0.000000] DMA32 4096 -> 1048576 > > [ 0.000000] Normal 1048576 -> 1048576 > > [ 0.000000] early_node_map[2] active PFN ranges > > [ 0.000000] 0: 0 -> 159 > > [ 0.000000] 0: 256 -> 262128 > > [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. > > [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 > > [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > > [ 0.000000] Processor #0 (Bootup-CPU) > > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > > [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 > > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > > [ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored. > > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) > > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) > > [ 0.000000] Setting APIC routing to flat > > [ 0.000000] Using ACPI (MADT) for SMP configuration information > > [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 > > [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000f0000 > > [ 0.000000] Nosave address range: 00000000000f0000 - 0000000000100000 > > [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) > > [ 0.000000] Built 1 zonelists. Total pages: 257320 > > [ 0.000000] Kernel command line: root=/dev/sda3 vga=0x318 video=vesafb:ywrap,mtrr:3 console=tty0 cons1 > > [ 0.000000] Initializing CPU#0 > > [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) > > > > Any ideas what I should try or suggestions on patches to remove/try. > > > > Thanks > > Ed > > --- > ~Randy > - > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@...r.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ > > - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists