Bootdata ok (command line is auto BOOT_IMAGE=2.6.18.2 ro root=900 panic=5 netconsole=514@1.2.3.4/eth2,514@1.2.3.5/00:E0:4C:02:74:B4) Linux version 2.6.18.2 (root@xxxxxx) (gcc version 3.4.6) #1 SMP Sat Nov 4 21:02:47 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff80000 (usable) BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data) BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS) BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) DMI 2.3 present. ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fa740 ACPI: RSDT (v001 A M I OEMRSDT 0x01000617 MSFT 0x00000097) @ 0x000000007ff80000 ACPI: FADT (v001 A M I OEMFACP 0x01000617 MSFT 0x00000097) @ 0x000000007ff80200 ACPI: MADT (v001 A M I OEMAPIC 0x01000617 MSFT 0x00000097) @ 0x000000007ff80390 ACPI: OEMB (v001 A M I AMI_OEM 0x01000617 MSFT 0x00000097) @ 0x000000007ff8e040 >>> ERROR: Invalid checksum ACPI: MCFG (v001 A M I OEMMCFG 0x01000617 MSFT 0x00000097) @ 0x000000007ff88840 ACPI: DSDT (v001 A0411 A0411000 0x00000000 INTL 0x02002026) @ 0x0000000000000000 On node 0 totalpages: 515811 DMA zone: 2857 pages, LIFO batch:0 DMA32 zone: 512954 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:6 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:6 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 88000000 (gap: 80000000:7fb00000) Built 1 zonelists. Total pages: 515811 Kernel command line: auto BOOT_IMAGE=2.6.18.2 ro root=900 panic=5 netconsole=514@1.2.3.4/eth2,514@1.2.3.5/00:E0:4C:02:74:B4 netconsole: local port 514 netconsole: local IP 1.2.3.4 netconsole: interface eth2 netconsole: remote port 514 netconsole: remote IP 1.2.3.5 netconsole: remote ethernet address 00:e0:4c:02:74:b4 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. time.c: Detected 3211.397 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Checking aperture... Memory: 2059912k/2096640k available (2661k kernel code, 36228k reserved, 1029k data, 192k init) Calibrating delay using timer specific routine.. 6428.41 BogoMIPS (lpj=12856820) Mount-cache hash table entries: 256 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K using mwait in idle threads. CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM1) Freeing SMP alternatives: 28k freed ACPI: Core revision 20060707 Using local APIC timer interrupts. result 12544469 Detected 12.544 MHz APIC timer. Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 6423.30 BogoMIPS (lpj=12846601) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM1) Intel(R) Pentium(R) D CPU 3.20GHz stepping 02 Brought up 2 CPUs testing NMI watchdog ... OK. migration_cost=814 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Boot video device is 0000:01:01.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15) intel_rng: FWH not detected SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-GART: No AMD northbridge found. PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: c000-cfff MEM window: ff900000-ff9fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: b000-bfff MEM window: ff800000-ff8fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: a000-afff MEM window: ff700000-ff7fffff PREFETCH window: fcb00000-feafffff GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1c.0 to 64 GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1c.3 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1c.4 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered Total HugeTLB memory allocated, 0 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.7) SGI XFS with large block/inode numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._PDC] (Node ffff810002f67210), AE_BAD_HEADER ACPI: Processor [CPU1] (supports 8 throttling states) ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._PDC] (Node ffff810002f67ad0), AE_BAD_HEADER ACPI: Getting cpuindex for acpiid 0x3 ACPI: Getting cpuindex for acpiid 0x4 Real Time Clock Driver v1.12ac Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:03:00.0 to 64 sky2 v1.5 addr 0xff9fc000 irq 177 Yukon-EC (0xb6) rev 2 sky2 eth0: addr 00:17:31:00:26:da ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:02:00.0 to 64 sky2 v1.5 addr 0xff8fc000 irq 169 Yukon-EC (0xb6) rev 2 sky2 eth1: addr 00:17:31:00:22:f2 8139too Fast Ethernet driver 0.9.27 GSI 18 sharing vector 0x32 and IRQ 18 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low) -> IRQ 50 eth2: RealTek RTL8139 at 0xffffc2000000cc00, 00:e0:4c:02:6c:45, IRQ 50 eth2: Identified 8139 chip type 'RTL-8100B/8139D' tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky netconsole: device eth2 not up yet, forcing it eth2: link up, 100Mbps, full-duplex, lpa 0x41E1 netconsole: carrier detect appears untrustworthy, waiting 4 seconds netconsole: network logging started Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH7: IDE controller at PCI slot 0000:00:1f.1 GSI 19 sharing vector 0x3A and IRQ 19 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 58 ICH7: chipset revision 1 ICH7: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: ST3160812A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: max request size: 512KiB hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 libata version 2.00 loaded. ahci 0000:00:1f.2: version 2.0 GSI 20 sharing vector 0x42 and IRQ 20 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 66 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part ata1: SATA max UDMA/133 cmd 0xFFFFC2000000ED00 ctl 0x0 bmdma 0x0 irq 74 ata2: SATA max UDMA/133 cmd 0xFFFFC2000000ED80 ctl 0x0 bmdma 0x0 irq 74 ata3: SATA max UDMA/133 cmd 0xFFFFC2000000EE00 ctl 0x0 bmdma 0x0 irq 74 ata4: SATA max UDMA/133 cmd 0xFFFFC2000000EE80 ctl 0x0 bmdma 0x0 irq 74 scsi0 : ahci ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7, max UDMA/133, 321672960 sectors: LBA48 NCQ (depth 31/32) ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/133 scsi1 : ahci ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: ATA-7, max UDMA/133, 321672960 sectors: LBA48 NCQ (depth 31/32) ata2.00: ata2: dev 0 multi count 16 ata2.00: configured for UDMA/133 scsi2 : ahci ata3: SATA link down (SStatus 0 SControl 300) scsi3 : ahci ata4: SATA link down (SStatus 0 SControl 300) Vendor: ATA Model: HDT722516DLA380 Rev: V43O Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: HDT722516DLA380 Rev: V43O Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sd 1:0:0:0: Attached scsi disk sdb serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice i2c /dev entries driver ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 66 md: raid1 personality registered for level 1 md: multipath personality registered for level -4 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 Netfilter messages via NETLINK v0.30. ip_tables: (C) 2000-2006 Netfilter Core Team TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: considering sda2 ... md: adding sda2 ... md: sda1 has different UUID to sda2 md: adding hda2 ... md: hda1 has different UUID to sda2 md: created md1 md: bind md: bind md: running: raid1: raid set md1 active with 2 out of 2 mirrors md: considering sda1 ... md: adding sda1 ... md: adding hda1 ... md: created md0 md: bind md: bind md: running: raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. Filesystem "md0": Disabling barriers, not supported by the underlying device XFS mounting filesystem md0 Starting XFS recovery on filesystem: md0 (logdev: internal) Ending XFS recovery on filesystem: md0 (logdev: internal) VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 192k freed Adding 995896k swap on /dev/md1. Priority:-1 extents:1 across:995896k Filesystem "md0": Disabling barriers, not supported by the underlying device Filesystem "md0": Disabling barriers, not supported by the underlying device XFS mounting filesystem sdb1 Starting XFS recovery on filesystem: sdb1 (logdev: internal) Ending XFS recovery on filesystem: sdb1 (logdev: internal)