Message-id: <45977081.6040303@shaw.ca>
Date:	Sun, 31 Dec 2006 02:10:41 -0600
From:	Robert Hancock <hancockr@...w.ca>
To:	linux-kernel <linux-kernel@...r.kernel.org>
Subject: ipw2200 device naming problems in 2.6.20-rc2-git1

Having some intermittent problems using my ipw2200 wireless card on 
2.6.20-rc2-git1 (may affect earlier versions as well) under Fedora Core 
6 i386. It appears that sometimes on bootup the interface gets named 
with a junk name like __tmp32284835 and it doesn't show up in ifconfig. 
rmmod/insmod on ipw2200 fixes the problem and it shows up as eth1 again. 
I don't think this problem happened with Fedora 2.6.18 kernels..

Full dmesg:

Linux version 2.6.20-rc2-git1 (rob@...alhost.localdomain) (gcc version 
4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Sun Dec 31 01:33:54 CST 2006
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 
000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 
00000000000a0000 type: 2
copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001fed0000 end: 
000000001ffd0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001ffd0000 size: 0000000000020c00 end: 
000000001fff0c00 type: 2
copy_e820_map() start: 000000001fff0c00 size: 000000000000b400 end: 
000000001fffc000 type: 4
copy_e820_map() start: 000000001fffc000 size: 0000000000004000 end: 
0000000020000000 type: 2
  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
  BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
  BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved)
  BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS)
  BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Entering add_active_range(0, 0, 131024) 0 entries of 256 used
Zone PFN ranges:
   DMA             0 ->     4096
   Normal       4096 ->   131024
   HighMem    131024 ->   131024
early_node_map[1] active PFN ranges
     0:        0 ->   131024
On node 0 totalpages: 131024
   DMA zone: 40 pages used for memmap
   DMA zone: 0 pages reserved
   DMA zone: 4056 pages, LIFO batch:0
   Normal zone: 1239 pages used for memmap
   Normal zone: 125689 pages, LIFO batch:31
   HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 COMPAQ                                ) @ 0x000f6560
ACPI: RSDT (v001 HP     CPQ0860  0x14070520 CPQ  0x00000001) @ 0x1fff0c84
ACPI: FADT (v002 HP     CPQ0860  0x00000002 CPQ  0x00000001) @ 0x1fff0c00
ACPI: SSDT (v001 COMPAQ  CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x1fff5c3c
ACPI: DSDT (v001 HP       nx7000 0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
Detected 1694.562 MHz processor.
Built 1 zonelists.  Total pages: 129745
Kernel command line: ro root=/dev/VolGroup00/LogVol00
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0150c000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c046c000 soft=c044c000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511704k/524096k available (2154k kernel code, 11760k reserved, 
935k data, 244k init, 0k highmem)
virtual kernel memory layout:
     fixmap  : 0xffc56000 - 0xfffff000   (3748 kB)
     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
     vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
     lowmem  : 0xc0000000 - 0xdffd0000   ( 511 MB)
       .init : 0xc040a000 - 0xc0447000   ( 244 kB)
       .data : 0xc031a915 - 0xc0404674   ( 935 kB)
       .text : 0xc0100000 - 0xc031a915   (2154 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3390.78 BogoMIPS 
(lpj=16953925)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 
00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f9bf 00000000 00000000 00002040 00000180 
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1.70GHz stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C046] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C046] bus is 0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C046._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C047._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C058._PRT]
ACPI: Power Resource [C18D] (on)
ACPI: Power Resource [C195] (on)
ACPI: Power Resource [C19C] (on)
ACPI: Power Resource [C1A6] (on)
ACPI: PCI Interrupt Link [C0C2] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C3] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C4] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C5] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10) *11
ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0d: ioport range 0x1100-0x113f has been reserved
pnp: 00:0d: ioport range 0x1200-0x121f has been reserved
PCI: Bridge: 0000:00:01.0
   IO window: 3000-3fff
   MEM window: 90400000-904fffff
   PREFETCH window: 98000000-9fffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
   IO window: 00002800-000028ff
   IO window: 00002c00-00002cff
   PREFETCH window: 30000000-33ffffff
   MEM window: 38000000-3bffffff
PCI: Bridge: 0000:00:1e.0
   IO window: 2000-2fff
   MEM window: 90000000-903fffff
   PREFETCH window: 30000000-33ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low) 
-> IRQ 5
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 327680 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2113k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1167530352.610:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 256M @ 0xb0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, 
low) -> IRQ 10
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
ata_piix 0000:00:1f.1: version 2.00ac7
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI 5 (level, low) 
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0x4C40 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4C48 irq 15
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/100, 156368016 sectors: LBA48
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : ata_piix
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG MP0804H  UE20 PQ: 0 ANSI: 5
SCSI device sda: 156368016 512-byte hdwr sectors (80060 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
SCSI device sda: 156368016 512-byte hdwr sectors (80060 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
  sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
scsi 1:0:0:0: CD-ROM            QSI      CDRW/DVD SBW-241 VH04 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44
Yenta: ISA IRQ mask 0x08d8, PCI irq 5
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:C1A3,PNP0f13:C1A4] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
nf_conntrack version 0.5.0 (4094 buckets, 32752 max)
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 244k freed
Write protecting the kernel read-only data: 633k
Time: tsc clocksource has been installed.
Time: acpi_pm clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI 10 (level, 
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 10, io base 0x000048c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI 5 (level, low) 
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x000048e0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI 5 (level, low) 
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 5, io base 0x00004c00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI 5 (level, low) 
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 5, io mem 0xa0000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: 
dm-devel@...hat.com
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1167530360.470:2): enforcing=1 old_enforcing=0 auid=4294967295
security:  3 users, 6 roles, 1583 types, 172 bools, 1 sens, 1024 cats
security:  59 classes, 49428 rules
security:  class dccp_socket not defined in policy
security:  permission dccp_recv in class node not defined in policy
security:  permission dccp_send in class node not defined in policy
security:  permission dccp_recv in class netif not defined in policy
security:  permission dccp_send in class netif not defined in policy
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1167530360.820:3): policy loaded auid=4294967295
input: PC Speaker as /class/input/input2
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [C0C3] -> GSI 10 (level, 
low) -> IRQ 10
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation 
<jketreno@...ux.intel.com>
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
intel_rng: FWH not detected
ieee1394: Initialized config rom entry `ip1394'
cs: IO port probe 0x100-0x3af: excluding 0x140-0x14f 0x200-0x20f 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI 10 (level, 
low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] 
MMIO=[90200000-902007ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI 5 (level, low) 
-> IRQ 5
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Floppy drive(s): fd0 is 1.44M
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [C0C3] -> GSI 10 (level, 
low) -> IRQ 10
eth1: RTL-8139C+ at 0xe09a4000, 00:02:3f:65:4d:74, IRQ 10
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f383800c298]
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, 
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI 10 (level, 
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 59425 usecs
intel8x0: clocking to 48000
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: AC Adapter [C134] (on-line)
ACPI: Battery Slot [C11F] (battery present)
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [C1BE]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [C136]
No dock devices found.
ibm_acpi: ec object not found
ACPI: Video Device [C0D0] (multi-head: yes  rom: no  post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device sda1): load_system_files(): Unsupported volume 
flags 0x4000 encountered.
NTFS-fs error (device sda1): load_system_files(): Volume has unsupported 
flags set.  Mounting read-only.  Run chkdsk and mount in Windows.
SELinux: initialized (dev sda1, type ntfs), uses genfs_contexts
Adding 1048568k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1 
across:1048568k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses 
genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
eth0: link down
ACPI: EC: evaluating _Q09
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): __tmp32284835: link is not ready
wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.6
wbsd: Copyright(c) Pierre Ossman
pnp: Device 00:02 activated.
mmc0: W83L51xD id 7112 at 0x248 irq 6 dma 0 PnP
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI 10 (level, 
low) -> IRQ 10
[drm] Initialized radeon 1.25.0 20060524 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
ADDRCONF(NETDEV_CHANGE): __tmp32284835: link becomes ready
ieee80211_crypt: registered algorithm 'CCMP'
__tmp32284835: no IPv6 routers present
ADDRCONF(NETDEV_UP): __tmp32284835: link is not ready
ACPI: PCI interrupt for device 0000:02:02.0 disabled
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI 5 (level, low) 
-> IRQ 5
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
eth1: no IPv6 routers present


-- 
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@...pamshaw.ca
Home Page: http://www.roberthancock.com/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists