| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20070112042627.28794.47002.sendpatchset@localhost.localdomain>
Date: Fri, 12 Jan 2007 05:26:27 +0100
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
To: linux-ide@...r.kernel.org
Cc: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>,
linux-kernel@...r.kernel.org
Subject: [PATCH 3/19] ide: it8213 driver update
[PATCH] ide: it8213 driver update
* set ATAPI/IORDY/TIME bits correctly in it8213_tuneproc()
* fix UDMA/MWDMA/SWDMA masks in it8213_init_hwif()
* in it8213_tune_chipset() SWDMA2 mode should be used instead of MWDMA0
* backport various fixes from piix/slc90e66 drivers:
- in it8213_tuneproc() the highest possible PIO mode is PIO4 (not PIO5)
- clear ATAPI/IORDY/TIME bits before setting them also for slave device
- use ->speedproc in it8213_config_drive_for_dma()
- don't try to tune PIO in config_chipset_for_pio()
- simplify is_slave calculation in it8213_tuneproc()
- misc cleanups
* fix it8213_ratemask() and it8213_tuneproc() comments
* simplify it8213_init_hwif()
* remove init_chipset_it8213()
* add missing Copyrights and update MODULE_AUTHOR()
* CodingStyle cleanups
* remove dead code
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
---
drivers/ide/pci/it8213.c | 172 ++++++++++++++++++-----------------------------
1 file changed, 66 insertions(+), 106 deletions(-)
Index: a/drivers/ide/pci/it8213.c
===================================================================
--- a.orig/drivers/ide/pci/it8213.c
+++ a/drivers/ide/pci/it8213.c
@@ -1,3 +1,11 @@
+/*
+ * ITE 8213 IDE driver
+ *
+ * Copyright (C) 2006 Jack Lee
+ * Copyright (C) 2006 Alan Cox
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
+ */
+
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/module.h>
@@ -14,14 +22,14 @@
* @drive: IDE drive
*
* Compute the available speeds for the devices on the interface. This
- * is all modes to ATA100 clipped by drive cable setup.
+ * is all modes to ATA133 clipped by drive cable setup.
*/
static u8 it8213_ratemask (ide_drive_t *drive)
{
u8 mode = 4;
if (!eighty_ninty_three(drive))
- mode = min(mode, (u8)1);
+ mode = min_t(u8, mode, 1);
return mode;
}
@@ -62,55 +70,57 @@ static u8 it8213_dma_2_pio (u8 xfer_rate
}
}
-static spinlock_t tune_lock = SPIN_LOCK_UNLOCKED;
-
/*
* it8213_tuneproc - tune a drive
* @drive: drive to tune
- * @mode_wanted: the target operating mode
- *
- * Load the timing settings for this device mode into the
- * controller. By the time we are called the mode has been
- * modified as neccessary to handle the absence of seperate
- * master/slave timers for MWDMA/PIO.
+ * @pio: desired PIO mode
*
- * This code is only used in pass through mode.
+ * Set the interface PIO mode.
*/
-static void it8213_tuneproc (ide_drive_t *drive, u8 pio)
+static void it8213_tuneproc (ide_drive_t *drive, u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
- int is_slave = (&hwif->drives[1] == drive);
+ int is_slave = drive->dn & 1;
int master_port = 0x40;
int slave_port = 0x44;
unsigned long flags;
u16 master_data;
u8 slave_data;
+ static DEFINE_SPINLOCK(tune_lock);
+ int control = 0;
- u8 timings[][2] = { { 0, 0 },
- { 0, 0 },
- { 1, 0 },
- { 2, 1 },
- { 2, 3 }, };
+ static const u8 timings[][2]= {
+ { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
- pio = ide_get_best_pio_mode(drive, pio, 5, NULL);
+ pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
spin_lock_irqsave(&tune_lock, flags);
pci_read_config_word(dev, master_port, &master_data);
+
+ if (pio > 1)
+ control |= 1; /* Programmable timing on */
+ if (drive->media != ide_disk)
+ control |= 4; /* ATAPI */
+ if (pio > 2)
+ control |= 2; /* IORDY */
if (is_slave) {
- master_data = master_data | 0x4000;
+ master_data |= 0x4000;
+ master_data &= ~0x0070;
if (pio > 1)
-
- master_data = master_data | 0x0070;
+ master_data = master_data | (control << 4);
pci_read_config_byte(dev, slave_port, &slave_data);
slave_data = slave_data & 0xf0;
- slave_data = slave_data | (((timings[pio][0] << 2) | (timings[pio][1]) << 0));
+ slave_data = slave_data | (timings[pio][0] << 2) | timings[pio][1];
} else {
- master_data = master_data & 0xccf8;
+ master_data &= ~0x3307;
if (pio > 1)
-
- master_data = master_data | 0x0007;
+ master_data = master_data | control;
master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
@@ -119,7 +129,6 @@ static void it8213_tuneproc (ide_drive_t
spin_unlock_irqrestore(&tune_lock, flags);
}
-
/**
* it8213_tune_chipset - set controller timings
* @drive: Drive to set up
@@ -130,7 +139,7 @@ static void it8213_tuneproc (ide_drive_t
* make the thing work.
*/
-static int it8213_tune_chipset (ide_drive_t *drive, byte xferspeed)
+static int it8213_tune_chipset (ide_drive_t *drive, u8 xferspeed)
{
ide_hwif_t *hwif = HWIF(drive);
@@ -154,15 +163,15 @@ static int it8213_tune_chipset (ide_driv
switch(speed) {
case XFER_UDMA_6:
case XFER_UDMA_4:
- case XFER_UDMA_2:u_speed = 2 << (drive->dn * 4); break;
+ case XFER_UDMA_2: u_speed = 2 << (drive->dn * 4); break;
case XFER_UDMA_5:
case XFER_UDMA_3:
- case XFER_UDMA_1:u_speed = 1 << (drive->dn * 4); break;
- case XFER_UDMA_0:u_speed = 0 << (drive->dn * 4); break;
+ case XFER_UDMA_1: u_speed = 1 << (drive->dn * 4); break;
+ case XFER_UDMA_0: u_speed = 0 << (drive->dn * 4); break;
break;
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
- case XFER_MW_DMA_0:
+ case XFER_SW_DMA_2:
break;
case XFER_PIO_4:
case XFER_PIO_3:
@@ -174,8 +183,7 @@ static int it8213_tune_chipset (ide_driv
return -1;
}
- if (speed >= XFER_UDMA_0)
- {
+ if (speed >= XFER_UDMA_0) {
if (!(reg48 & u_flag))
pci_write_config_byte(dev, 0x48, reg48 | u_flag);
if (speed >= XFER_UDMA_5) {
@@ -186,14 +194,12 @@ static int it8213_tune_chipset (ide_driv
if ((reg4a & a_speed) != u_speed)
pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
- if (speed > XFER_UDMA_2)
- {
+ if (speed > XFER_UDMA_2) {
if (!(reg54 & v_flag))
pci_write_config_byte(dev, 0x54, reg54 | v_flag);
} else
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
- } else /*if(speed >= XFER_UDMA_0)*/
- {
+ } else {
if (reg48 & u_flag)
pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
if (reg4a & a_speed)
@@ -202,11 +208,10 @@ static int it8213_tune_chipset (ide_driv
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
if (reg55 & w_flag)
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
- }
+ }
it8213_tuneproc(drive, it8213_dma_2_pio(speed));
return ide_config_drive_speed(drive, speed);
- }
-
+}
/*
* config_chipset_for_dma - configure for DMA
@@ -217,48 +222,17 @@ static int it8213_tune_chipset (ide_driv
static int config_chipset_for_dma (ide_drive_t *drive)
{
- u8 speed = ide_dma_speed(drive, it8213_ratemask(drive));
+ u8 speed = ide_dma_speed(drive, it8213_ratemask(drive));
+
if (!speed)
- {
- u8 tspeed = ide_get_best_pio_mode(drive, 255, 5, NULL);
- speed = it8213_dma_2_pio(XFER_PIO_0 + tspeed);
- }
-// config_it8213_chipset_for_pio(drive, !speed);
+ return 0;
+
it8213_tune_chipset(drive, speed);
+
return ide_dma_enable(drive);
}
/**
- * config_it8213_chipset_for_pio - set drive timings
- * @drive: drive to tune
- * @speed we want
- *
- * Compute the best pio mode we can for a given device. We must
- * pick a speed that does not cause problems with the other device
- * on the cable.
- */
-/*
-static void config_it8213_chipset_for_pio (ide_drive_t *drive, byte set_speed)
-{
- ide_hwif_t *hwif = HWIF(drive);
-// u8 unit = drive->select.b.unit;
- ide_hwif_t *hwif = drive->hwif;
- ide_drive_t *pair = &hwif->drives[1-unit];
- u8 speed = 0, set_pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
- u8 pair_pio;
-
- if(pair != NULL) {
- pair_pio = ide_get_best_pio_mode(pair, 255, 5, NULL);
- if(pair_pio < set_pio)
- set_pio = pair_pio;
- }
- it8213_tuneproc(drive, set_pio);
- speed = XFER_PIO_0 + set_pio;
- if (set_speed)
- (void) ide_config_drive_speed(drive, speed);
-}
-*/
-/**
* it8213_configure_drive_for_dma - set up for DMA transfers
* @drive: drive we are going to set up
*
@@ -270,26 +244,19 @@ static void config_it8213_chipset_for_pi
static int it8213_config_drive_for_dma (ide_drive_t *drive)
{
-// ide_hwif_t *hwif = drive->hwif;
-// struct hd_driveid *id = drive->id;
- ide_hwif_t *hwif = HWIF(drive);
+ ide_hwif_t *hwif = drive->hwif;
+
if (ide_use_dma(drive)) {
if (config_chipset_for_dma(drive))
return hwif->ide_dma_on(drive);
}
-// config_it8213_chipset_for_pio(drive, 1);
- hwif->tuneproc(drive, 255);
- return hwif->ide_dma_off_quietly(drive);
-}
+ hwif->speedproc(drive, XFER_PIO_0
+ + ide_get_best_pio_mode(drive, 255, 4, NULL));
-static unsigned int __devinit init_chipset_it8213(struct pci_dev *dev, const char *name)
-{
- printk(KERN_INFO "it8213: controller in IDE mode.\n");
- return 0;
+ return hwif->ide_dma_off_quietly(drive);
}
-
/**
* init_hwif_it8213 - set up hwif structs
* @hwif: interface to set up
@@ -302,9 +269,6 @@ static unsigned int __devinit init_chips
static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
{
u8 reg42h = 0, ata66 = 0;
- u8 mask = 0x02;
-
- hwif->atapi_dma = 1;
hwif->speedproc = &it8213_tune_chipset;
hwif->tuneproc = &it8213_tuneproc;
@@ -315,19 +279,19 @@ static void __devinit init_hwif_it8213(i
hwif->drives[1].autotune = 1;
if (!hwif->dma_base)
- goto fallback;
+ return;
+
hwif->atapi_dma = 1;
- hwif->ultra_mask = 0x7f;
- hwif->mwdma_mask = 0x07;
- hwif->swdma_mask = 0x07;
+ hwif->ultra_mask = 0x3f;
+ hwif->mwdma_mask = 0x06;
+ hwif->swdma_mask = 0x04;
pci_read_config_byte(hwif->pci_dev, 0x42, ®42h);
- ata66 = (reg42h & mask) ? 0 : 1;
+ ata66 = (reg42h & 0x02) ? 0 : 1;
hwif->ide_dma_check = &it8213_config_drive_for_dma;
if (!(hwif->udma_four))
hwif->udma_four = ata66;
-// hwif->udma_four = 0;
/*
* The BIOS often doesn't set up DMA on this controller
@@ -338,20 +302,15 @@ static void __devinit init_hwif_it8213(i
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
- return;
-fallback:
- hwif->autodma = 0;
- return;
}
#define DECLARE_ITE_DEV(name_str) \
{ \
.name = name_str, \
- .init_chipset = init_chipset_it8213, \
.init_hwif = init_hwif_it8213, \
.channels = 1, \
- .autodma = AUTODMA, \
+ .autodma = AUTODMA, \
.enablebits = {{0x41,0x80,0x80}}, \
.bootable = ON_BOARD, \
}
@@ -393,10 +352,11 @@ static struct pci_driver driver = {
static int __init it8213_ide_init(void)
{
- return ide_pci_register_driver(&driver); }
+ return ide_pci_register_driver(&driver);
+}
module_init(it8213_ide_init);
-MODULE_AUTHOR("Jack and Alan Cox"); /* Update this */
+MODULE_AUTHOR("Jack Lee, Alan Cox");
MODULE_DESCRIPTION("PCI driver module for the ITE 8213");
MODULE_LICENSE("GPL");
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists