Linux version 2.6.19test (root@debian64) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #2 SMP PREEMPT Sat Jan 20 22:19:20 CET 2007 Command line: root=/dev/md1 ro BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007fff0000 (usable) BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS) BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 524272) 1 entries of 256 used end_pfn_map = 1048576 DMI 2.3 present. ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7d30 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007fff3040 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007fff30c0 ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x000000007fff9900 ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x000000007fff9b40 ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007fff9c40 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007fff9840 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000 Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 524272) 1 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 early_node_map[2] active PFN ranges 0: 0 -> 159 0: 256 -> 524272 On node 0 totalpages: 524175 DMA zone: 56 pages used for memmap DMA zone: 10 pages reserved DMA zone: 3933 pages, LIFO batch:0 DMA32 zone: 7111 pages used for memmap DMA32 zone: 513065 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Setting APIC routing to physical flat Using ACPI (MADT) for SMP configuration information Nosave address range: 000000000009f000 - 00000000000a0000 Nosave address range: 00000000000a0000 - 00000000000f0000 Nosave address range: 00000000000f0000 - 0000000000100000 Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 32320 bytes of per cpu data Built 1 zonelists. Total pages: 516998 Kernel command line: root=/dev/md1 ro Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Checking aperture... CPU 0: aperture @ 1844000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 2059352k/2097088k available (3025k kernel code, 37076k reserved, 1382k data, 208k init) Calibrating delay using timer specific routine.. 4425.39 BogoMIPS (lpj=8850788) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20060707 Using local APIC timer interrupts. result 12564452 Detected 12.564 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4422.96 BogoMIPS (lpj=8845921) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01 CPU 1: Syncing TSC to CPU 0. CPU 1: synchronized TSC with CPU 0 (last diff -1 cycles, maxerr 547 cycles) Brought up 2 CPUs testing NMI watchdog ... OK. Disabling vsyscall due to use of PM timer time.c: Using 3.579545 MHz WALL PM GTOD PM timer. time.c: Detected 2211.339 MHz processor. migration_cost=226 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 PCI: No mmconfig possible on device 00:18 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:09.0 Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 *12 14 15) ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 3 *4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 *7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices SCSI subsystem initialized libata version 2.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-DMA: Disabling IOMMU. pnp: 00:01: ioport range 0x4000-0x407f could not be reserved pnp: 00:01: ioport range 0x4080-0x40ff has been reserved pnp: 00:01: ioport range 0x4400-0x447f has been reserved pnp: 00:01: ioport range 0x4480-0x44ff could not be reserved pnp: 00:01: ioport range 0x4800-0x487f has been reserved pnp: 00:01: ioport range 0x4880-0x48ff has been reserved PCI: Bridge: 0000:00:09.0 IO window: a000-afff MEM window: d0000000-d1ffffff PREFETCH window: 88000000-880fffff PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: c8000000-cfffffff PREFETCH window: c0000000-c7ffffff PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1169328271.472:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) JFS: nTxBlock = 8192, nTxLock = 65536 SGI XFS with large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler cfq registered (default) PCI: Linking AER extended capability on 0000:00:0b.0 PCI: Found HT MSI mapping on 0000:00:0b.0 with capability disabled PCI: Found HT MSI mapping on 0000:00:00.0 with capability enabled PCI: Linking AER extended capability on 0000:00:0c.0 PCI: Found HT MSI mapping on 0000:00:0c.0 with capability disabled PCI: Found HT MSI mapping on 0000:00:00.0 with capability enabled PCI: Linking AER extended capability on 0000:00:0d.0 PCI: Found HT MSI mapping on 0000:00:0d.0 with capability disabled PCI: Found HT MSI mapping on 0000:00:00.0 with capability enabled PCI: Linking AER extended capability on 0000:00:0e.0 PCI: Found HT MSI mapping on 0000:00:0e.0 with capability disabled PCI: Found HT MSI mapping on 0000:00:00.0 with capability enabled PCI: Setting latency timer of device 0000:00:0b.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0b.0:pcie00] Allocate Port Service[0000:00:0b.0:pcie03] PCI: Setting latency timer of device 0000:00:0c.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0c.0:pcie00] Allocate Port Service[0000:00:0c.0:pcie03] PCI: Setting latency timer of device 0000:00:0d.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0d.0:pcie00] Allocate Port Service[0000:00:0d.0:pcie03] PCI: Setting latency timer of device 0000:00:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0e.0:pcie00] Allocate Port Service[0000:00:0e.0:pcie03] ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) sata_nv 0000:00:07.0: version 3.2 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23 sata_nv 0000:00:07.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:07.0 to 64 ata1: SATA max UDMA/133 cmd 0xFFFFC20000028480 ctl 0xFFFFC200000284A0 bmdma 0xD800 irq 23 ata2: SATA max UDMA/133 cmd 0xFFFFC20000028580 ctl 0xFFFFC200000285A0 bmdma 0xD808 irq 23 scsi0 : sata_nv ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATAPI, max UDMA/33 ata1.00: configured for UDMA/33 scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183L SB00 PQ: 0 ANSI: 5 ata1: bounce limit 0xFFFFFFFF, segment boundary 0xFFFF, hw segs 127 sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 0:0:0:0: Attached scsi CD-ROM sr0 sr 0:0:0:0: Attached scsi generic sg0 type 5 ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22 sata_nv 0000:00:08.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:08.0 to 64 ata3: SATA max UDMA/133 cmd 0xFFFFC2000002A480 ctl 0xFFFFC2000002A4A0 bmdma 0xC400 irq 22 ata4: SATA max UDMA/133 cmd 0xFFFFC2000002A580 ctl 0xFFFFC2000002A5A0 bmdma 0xC408 irq 22 scsi2 : sata_nv ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata3.00: ATA-7, max UDMA/133, 488395055 sectors: LBA48 ata3.00: ata3: dev 0 multi count 1 ata3.00: configured for UDMA/133 scsi3 : sata_nv ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 1) ata4.00: ata4: dev 0 multi count 1 ata4.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5 ata3: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 > sd 2:0:0:0: Attached scsi disk sda sd 2:0:0:0: Attached scsi generic sg1 type 0 scsi 3:0:0:0: Direct-Access ATA WDC WD2500YD-01N 10.0 PQ: 0 ANSI: 5 ata4: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 sdb12 > sd 3:0:0:0: Attached scsi disk sdb sd 3:0:0:0: Attached scsi generic sg2 type 0 pata_amd 0000:00:06.0: version 0.2.4 PCI: Setting latency timer of device 0000:00:06.0 to 64 ata5: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14 ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15 scsi4 : pata_amd ata5.00: ATA-6, max UDMA/100, 156299375 sectors: LBA48 ata5.00: ata5: dev 0 multi count 1 ata5.00: configured for UDMA/100 scsi5 : pata_amd ata6.00: ATAPI, max UDMA/33 ata6.00: configured for UDMA/33 scsi 4:0:0:0: Direct-Access ATA WDC WD800JB-00ET 77.0 PQ: 0 ANSI: 5 SCSI device sdc: 156299375 512-byte hdwr sectors (80025 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back SCSI device sdc: 156299375 512-byte hdwr sectors (80025 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back sdc: sdc1 sdc2 sd 4:0:0:0: Attached scsi disk sdc sd 4:0:0:0: Attached scsi generic sg3 type 0 scsi 5:0:0:0: CD-ROM PIONEER DVD-ROM DVD-105 1.33 PQ: 0 ANSI: 5 sr1: scsi3-mmc drive: 16x/40x cd/rw xa/form2 cdda tray sr 5:0:0:0: Attached scsi CD-ROM sr1 sr 5:0:0:0: Attached scsi generic sg4 type 5 PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 input: AT Translated Set 2 keyboard as /class/input/input1 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com device-mapper: multipath: version 1.0.5 loaded device-mapper: multipath round-robin: version 1.0.0 loaded EDAC MC: Ver: 2.0.1 Jan 20 2007 TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' ACPI: (supports S0 S1 S3 S4 S5) drivers/rtc/hctosys.c: unable to open rtc device (rtc0) md: Autodetecting RAID arrays. md: autorun ... [..] raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. ReiserFS: md1: found reiserfs format "3.6" with standard journal ReiserFS: md1: using ordered data mode ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: md1: checking transaction log (md1) ReiserFS: md1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 208k freed ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: irq 21, io mem 0xfeb00000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 20, io mem 0xd2003000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.57. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:0a.0 to 64 forcedeth: using HIGHDMA usb 2-4: new low speed USB device using ohci_hcd and address 2 usb 2-4: configuration #1 chosen from 1 choice eth0: forcedeth.c: subsystem: 01043:8141 bound to 0000:00:0a.0 i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:05:0c.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17 skge 1.9 addr 0xd1004000 irq 17 chip Yukon-Lite rev 9 skge eth1: addr 00:15:f2:50:d7:70 ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:05:07.2[B] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[d100f000-d100f7ff] Max Packet=[2048] IR/IT contexts=[4/8] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 ACPI: PCI Interrupt 0000:05:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16 usbcore: registered new interface driver hiddev input: Logitech USB-PS/2 Optical Mouse as /class/input/input2 input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-4 usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[d100e000-d100e7ff] Max Packet=[2048] IR/IT contexts=[4/8] ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17 Installing spdif_bug patch: Audigy 2 ZS [SB0350] gameport: EMU10K1 is pci0000:05:07.1/gameport0, io 0xa400, speed 1205kHz ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c015112bb16] eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) eth1394: eth3: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1) ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d800007ab4d6] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance it87: Found IT8712F chip at 0x290, revision 7 it87: in3 is VCC (+5V) it87: in7 is VCCH (+5V Stand-By) powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ processors (version 2.00.00) powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8 powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xa powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12 usbcore: registered new interface driver usbmouse drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. sr1: CDROM not ready. Make sure there is a disc in the drive. [..] Adding 1951888k swap on /dev/mapper/cswap1. Priority:-1 extents:1 across:1951888k Adding 1951888k swap on /dev/mapper/cswap2. Priority:-2 extents:1 across:1951888k NET: Registered protocol family 10 lo: Disabled Privacy Extensions eth0: no IPv6 routers present lp: driver loaded but no devices found ppdev: user-space parallel port driver Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 cdrom: sr0: mrw address space DMA selected cdrom: sr0: mrw address space DMA selected ISO 9660 Extensions: Microsoft Joliet Level 1 ISOFS: changing to secondary root cdrom: sr0: mrw address space DMA selected cdrom: sr0: mrw address space DMA selected ISO 9660 Extensions: Microsoft Joliet Level 1 ISOFS: changing to secondary root