| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20070209193405.GB2637@localhost.localdomain>
Date: Fri, 9 Feb 2007 20:34:05 +0100
From: Ondrej Zajicek <santiago@...reenet.org>
To: James Simmons <jsimmons@...radead.org>
Cc: Andrew Morton <akpm@...l.org>, linux-kernel@...r.kernel.org,
linux-fbdev-devel@...ts.sourceforge.net,
Jiri Slaby <jirislaby@...il.com>
Subject: [PATCH] fbdev driver for S3 Trio/Virge, updated
This patch adds driver for S3 Trio / S3 Virge. Driver is tested
with most versions of S3 Trio and S3 Virge, on i386.
It is tested both as compiled-in and module. It is against
linux-2.6.20 .
This is version 3. There are some minor modifications from version 2
(mostly coding style cleanups).
Signed-off-by: Ondrej Zajicek <santiago@...reenet.org>
---
diff -uprN -X linux-2.6.20-x/Documentation/dontdiff linux-2.6.20-x/Documentation/fb/s3fb.txt linux-2.6.20-s3fb/Documentation/fb/s3fb.txt
--- linux-2.6.20-x/Documentation/fb/s3fb.txt 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.20-s3fb/Documentation/fb/s3fb.txt 2007-02-05 14:26:14.000000000 +0100
@@ -0,0 +1,78 @@
+
+ s3fb - fbdev driver for S3 Trio/Virge chips
+ ===========================================
+
+
+Supported Hardware
+==================
+
+ S3 Trio32
+ S3 Trio64 (and variants V+, UV+, V2/DX, V2/GX)
+ S3 Virge (and variants VX, DX, GX and GX2+)
+ S3 Plato/PX (completely untested)
+ S3 Aurora64V+ (completely untested)
+
+ - only PCI bus supported
+ - only BIOS initialized VGA devices supported
+ - probably not working on big endian
+
+I tested s3fb on Trio64 (plain, V+ and V2/DX) and Virge (plain, VX, DX),
+all on i386.
+
+
+Supported Features
+==================
+
+ * 4 bpp pseudocolor modes (with 18bit palette, two variants)
+ * 8 bpp pseudocolor mode (with 18bit palette)
+ * 16 bpp truecolor modes (RGB 555 and RGB 565)
+ * 24 bpp truecolor mode (RGB 888) on (only on Virge VX)
+ * 32 bpp truecolor mode (RGB 888) on (not on Virge VX)
+ * text mode (activated by bpp = 0)
+ * interlaced mode variant (not available in text mode)
+ * doublescan mode variant (not available in text mode)
+ * panning in both directions
+ * suspend/resume support
+ * DPMS support
+
+Text mode is supported even in higher resolutions, but there is limitation
+to lower pixclocks (maximum between 50-60 MHz, depending on specific hardware).
+This limitation is not enforced by driver. Text mode supports 8bit wide fonts
+only (hardware limitation) and 16bit tall fonts (driver limitation).
+
+There are two 4 bpp modes. First mode (selected if nonstd == 0) is mode with
+packed pixels, high nibble first. Second mode (selected if nonstd == 1) is mode
+with interleaved planes (1 byte interleave), MSB first. Both modes support
+8bit wide fonts only (driver limitation).
+
+Suspend/resume works on systems that initialize video card during resume and
+if device is active (for example used by fbcon).
+
+
+Missing Features
+================
+(alias TODO list)
+
+ * secondary (not initialized by BIOS) device support
+ * big endian support
+ * Zorro bus support
+ * MMIO support
+ * 24 bpp mode support on more cards
+ * support for fontwidths != 8 in 4 bpp modes
+ * support for fontheight != 16 in text mode
+ * composite and external sync (is anyone able to test this?)
+ * hardware cursor
+ * video overlay support
+ * vsync synchronization
+ * feature connector support
+ * acceleration support (8514-like 2D, Virge 3D, busmaster transfers)
+ * better values for some magic registers (performance issues)
+
+
+Known bugs
+==========
+
+ * cursor disable in text mode doesn't work
+
+--
+Ondrej Zajicek <santiago@...reenet.org>
diff -uprN -X linux-2.6.20-x/Documentation/dontdiff linux-2.6.20-x/drivers/video/Kconfig linux-2.6.20-s3fb/drivers/video/Kconfig
--- linux-2.6.20-x/drivers/video/Kconfig 2007-02-04 19:44:54.000000000 +0100
+++ linux-2.6.20-s3fb/drivers/video/Kconfig 2007-02-05 19:05:50.000000000 +0100
@@ -85,6 +85,14 @@ config FB_CFB_IMAGEBLIT
blitting. This is used by drivers that don't provide their own
(accelerated) version.
+config FB_SVGALIB
+ tristate
+ depends on FB
+ default n
+ ---help---
+ Common utility functions useful to fbdev drivers of VGA-based
+ cards.
+
config FB_MACMODES
tristate
depends on FB
@@ -1147,6 +1155,17 @@ config FB_S3TRIO
help
If you have a S3 Trio say Y. Say N for S3 Virge.
+config FB_S3
+ tristate "S3 Trio/Virge support"
+ depends on FB && PCI
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ select FB_TILEBLITTING
+ select FB_SVGALIB
+ ---help---
+ Driver for graphics boards with S3 Trio / S3 Virge chip.
+
config FB_SAVAGE
tristate "S3 Savage support"
depends on FB && PCI && EXPERIMENTAL
diff -uprN -X linux-2.6.20-x/Documentation/dontdiff linux-2.6.20-x/drivers/video/Makefile linux-2.6.20-s3fb/drivers/video/Makefile
--- linux-2.6.20-x/drivers/video/Makefile 2007-02-04 19:44:54.000000000 +0100
+++ linux-2.6.20-s3fb/drivers/video/Makefile 2007-02-05 14:26:14.000000000 +0100
@@ -17,6 +17,7 @@ obj-$(CONFIG_SYSFS) += backlight/
obj-$(CONFIG_FB_CFB_FILLRECT) += cfbfillrect.o
obj-$(CONFIG_FB_CFB_COPYAREA) += cfbcopyarea.o
obj-$(CONFIG_FB_CFB_IMAGEBLIT) += cfbimgblt.o
+obj-$(CONFIG_FB_SVGALIB) += svgalib.o
obj-$(CONFIG_FB_MACMODES) += macmodes.o
obj-$(CONFIG_FB_DDC) += fb_ddc.o
@@ -54,6 +55,7 @@ obj-$(CONFIG_FB_S3TRIO) += S3t
obj-$(CONFIG_FB_FM2) += fm2fb.o
obj-$(CONFIG_FB_CYBLA) += cyblafb.o
obj-$(CONFIG_FB_TRIDENT) += tridentfb.o
+obj-$(CONFIG_FB_S3) += s3fb.o vgastate.o
obj-$(CONFIG_FB_STI) += stifb.o
obj-$(CONFIG_FB_FFB) += ffb.o sbuslib.o
obj-$(CONFIG_FB_CG6) += cg6.o sbuslib.o
diff -uprN -X linux-2.6.20-x/Documentation/dontdiff linux-2.6.20-x/drivers/video/s3fb.c linux-2.6.20-s3fb/drivers/video/s3fb.c
--- linux-2.6.20-x/drivers/video/s3fb.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.20-s3fb/drivers/video/s3fb.c 2007-02-09 19:14:12.000000000 +0100
@@ -0,0 +1,1180 @@
+/*
+ * linux/drivers/video/s3fb.c -- Frame buffer device driver for S3 Trio/Virge
+ *
+ * Copyright (c) 2006-2007 Ondrej Zajicek <santiago@...reenet.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ *
+ * Code is based on David Boucher's viafb (http://davesdomain.org.uk/viafb/)
+ * which is based on the code of neofb.
+ */
+
+#include <linux/version.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/mm.h>
+#include <linux/tty.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/fb.h>
+#include <linux/svga.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/console.h> /* Why should fb driver call console functions? because acquire_console_sem() */
+#include <video/vga.h>
+
+#ifdef CONFIG_MTRR
+#include <asm/mtrr.h>
+#endif
+
+struct s3fb_info {
+ int chip, rev, mclk_freq;
+ int mtrr_reg;
+ struct vgastate state;
+ struct mutex open_lock;
+ unsigned int ref_count;
+ u32 pseudo_palette[16];
+};
+
+
+/* ------------------------------------------------------------------------- */
+
+static const struct svga_fb_format s3fb_formats[] = {
+ { 0, {0, 6, 0}, {0, 6, 0}, {0, 6, 0}, {0, 0, 0}, 0,
+ FB_TYPE_TEXT, FB_AUX_TEXT_SVGA_STEP4, FB_VISUAL_PSEUDOCOLOR, 8, 16},
+ { 4, {0, 6, 0}, {0, 6, 0}, {0, 6, 0}, {0, 0, 0}, 0,
+ FB_TYPE_PACKED_PIXELS, 0, FB_VISUAL_PSEUDOCOLOR, 8, 16},
+ { 4, {0, 6, 0}, {0, 6, 0}, {0, 6, 0}, {0, 0, 0}, 1,
+ FB_TYPE_INTERLEAVED_PLANES, 1, FB_VISUAL_PSEUDOCOLOR, 8, 16},
+ { 8, {0, 6, 0}, {0, 6, 0}, {0, 6, 0}, {0, 0, 0}, 0,
+ FB_TYPE_PACKED_PIXELS, 0, FB_VISUAL_PSEUDOCOLOR, 4, 8},
+ {16, {10, 5, 0}, {5, 5, 0}, {0, 5, 0}, {0, 0, 0}, 0,
+ FB_TYPE_PACKED_PIXELS, 0, FB_VISUAL_TRUECOLOR, 2, 4},
+ {16, {11, 5, 0}, {5, 6, 0}, {0, 5, 0}, {0, 0, 0}, 0,
+ FB_TYPE_PACKED_PIXELS, 0, FB_VISUAL_TRUECOLOR, 2, 4},
+ {24, {16, 8, 0}, {8, 8, 0}, {0, 8, 0}, {0, 0, 0}, 0,
+ FB_TYPE_PACKED_PIXELS, 0, FB_VISUAL_TRUECOLOR, 1, 2},
+ {32, {16, 8, 0}, {8, 8, 0}, {0, 8, 0}, {0, 0, 0}, 0,
+ FB_TYPE_PACKED_PIXELS, 0, FB_VISUAL_TRUECOLOR, 1, 2},
+ SVGA_FORMAT_END
+};
+
+
+static const struct svga_pll s3_pll = {3, 129, 3, 33, 0, 3,
+ 60000, 240000, 14318};
+
+static const int s3_memsizes[] = {4096, 0, 3072, 8192, 2048, 6144, 1024, 512};
+
+static const char * const s3_names[] = {"S3 Unknown", "S3 Trio32", "S3 Trio64", "S3 Trio64V+",
+ "S3 Trio64UV+", "S3 Trio64V2/DX", "S3 Trio64V2/GX",
+ "S3 Plato/PX", "S3 Aurora64VP", "S3 Virge",
+ "S3 Virge/VX", "S3 Virge/DX", "S3 Virge/GX",
+ "S3 Virge/GX2", "S3 Virge/GX2P", "S3 Virge/GX2P"};
+
+#define CHIP_UNKNOWN 0x00
+#define CHIP_732_TRIO32 0x01
+#define CHIP_764_TRIO64 0x02
+#define CHIP_765_TRIO64VP 0x03
+#define CHIP_767_TRIO64UVP 0x04
+#define CHIP_775_TRIO64V2_DX 0x05
+#define CHIP_785_TRIO64V2_GX 0x06
+#define CHIP_551_PLATO_PX 0x07
+#define CHIP_M65_AURORA64VP 0x08
+#define CHIP_325_VIRGE 0x09
+#define CHIP_988_VIRGE_VX 0x0A
+#define CHIP_375_VIRGE_DX 0x0B
+#define CHIP_385_VIRGE_GX 0x0C
+#define CHIP_356_VIRGE_GX2 0x0D
+#define CHIP_357_VIRGE_GX2P 0x0E
+#define CHIP_359_VIRGE_GX2P 0x0F
+
+#define CHIP_XXX_TRIO 0x80
+#define CHIP_XXX_TRIO64V2_DXGX 0x81
+#define CHIP_XXX_VIRGE_DXGX 0x82
+
+#define CHIP_UNDECIDED_FLAG 0x80
+#define CHIP_MASK 0xFF
+
+/* CRT timing register sets */
+
+static const struct vga_regset s3_h_total_regs[] = {{0x00, 0, 7}, {0x5D, 0, 0}, VGA_REGSET_END};
+static const struct vga_regset s3_h_display_regs[] = {{0x01, 0, 7}, {0x5D, 1, 1}, VGA_REGSET_END};
+static const struct vga_regset s3_h_blank_start_regs[] = {{0x02, 0, 7}, {0x5D, 2, 2}, VGA_REGSET_END};
+static const struct vga_regset s3_h_blank_end_regs[] = {{0x03, 0, 4}, {0x05, 7, 7}, VGA_REGSET_END};
+static const struct vga_regset s3_h_sync_start_regs[] = {{0x04, 0, 7}, {0x5D, 4, 4}, VGA_REGSET_END};
+static const struct vga_regset s3_h_sync_end_regs[] = {{0x05, 0, 4}, VGA_REGSET_END};
+
+static const struct vga_regset s3_v_total_regs[] = {{0x06, 0, 7}, {0x07, 0, 0}, {0x07, 5, 5}, {0x5E, 0, 0}, VGA_REGSET_END};
+static const struct vga_regset s3_v_display_regs[] = {{0x12, 0, 7}, {0x07, 1, 1}, {0x07, 6, 6}, {0x5E, 1, 1}, VGA_REGSET_END};
+static const struct vga_regset s3_v_blank_start_regs[] = {{0x15, 0, 7}, {0x07, 3, 3}, {0x09, 5, 5}, {0x5E, 2, 2}, VGA_REGSET_END};
+static const struct vga_regset s3_v_blank_end_regs[] = {{0x16, 0, 7}, VGA_REGSET_END};
+static const struct vga_regset s3_v_sync_start_regs[] = {{0x10, 0, 7}, {0x07, 2, 2}, {0x07, 7, 7}, {0x5E, 4, 4}, VGA_REGSET_END};
+static const struct vga_regset s3_v_sync_end_regs[] = {{0x11, 0, 3}, VGA_REGSET_END};
+
+static const struct vga_regset s3_line_compare_regs[] = {{0x18, 0, 7}, {0x07, 4, 4}, {0x09, 6, 6}, {0x5E, 6, 6}, VGA_REGSET_END};
+static const struct vga_regset s3_start_address_regs[] = {{0x0d, 0, 7}, {0x0c, 0, 7}, {0x31, 4, 5}, {0x51, 0, 1}, VGA_REGSET_END};
+static const struct vga_regset s3_offset_regs[] = {{0x13, 0, 7}, {0x51, 4, 5}, VGA_REGSET_END}; /* set 0x43 bit 2 to 0 */
+
+static const struct svga_timing_regs s3_timing_regs = {
+ s3_h_total_regs, s3_h_display_regs, s3_h_blank_start_regs,
+ s3_h_blank_end_regs, s3_h_sync_start_regs, s3_h_sync_end_regs,
+ s3_v_total_regs, s3_v_display_regs, s3_v_blank_start_regs,
+ s3_v_blank_end_regs, s3_v_sync_start_regs, s3_v_sync_end_regs,
+};
+
+
+/* ------------------------------------------------------------------------- */
+
+/* Module parameters */
+
+
+static char *mode = "640x480-8@60";
+
+#ifdef CONFIG_MTRR
+static int mtrr = 1;
+#endif
+
+static int fasttext = 1;
+
+
+MODULE_AUTHOR("(c) 2006-2007 Ondrej Zajicek <santiago@...reenet.org>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("fbdev driver for S3 Trio/Virge");
+
+module_param(mode, charp, 0444);
+MODULE_PARM_DESC(mode, "Default video mode ('640x480-8@60', etc)");
+
+#ifdef CONFIG_MTRR
+module_param(mtrr, int, 0444);
+MODULE_PARM_DESC(mtrr, "Enable write-combining with MTRR (1=enable, 0=disable, default=1)");
+#endif
+
+module_param(fasttext, int, 0644);
+MODULE_PARM_DESC(fasttext, "Enable S3 fast text mode (1=enable, 0=disable, default=1)");
+
+
+/* ------------------------------------------------------------------------- */
+
+/* Set font in S3 fast text mode */
+
+static void s3fb_settile_fast(struct fb_info *info, struct fb_tilemap *map)
+{
+ const u8 *font = map->data;
+ u8* fb = (u8 *) info->screen_base;
+ int i, c;
+
+ if ((map->width != 8) || (map->height != 16) ||
+ (map->depth != 1) || (map->length != 256)) {
+ printk(KERN_ERR "fb%d: unsupported font parameters: width %d, height %d, depth %d, length %d\n",
+ info->node, map->width, map->height, map->depth, map->length);
+ return;
+ }
+
+ fb += 2;
+ for (i = 0; i < map->height; i++) {
+ for (c = 0; c < map->length; c++) {
+ fb[c * 4] = font[c * map->height + i];
+ }
+ fb += 1024;
+ }
+}
+
+
+
+static struct fb_tile_ops s3fb_tile_ops = {
+ .fb_settile = svga_settile,
+ .fb_tilecopy = svga_tilecopy,
+ .fb_tilefill = svga_tilefill,
+ .fb_tileblit = svga_tileblit,
+ .fb_tilecursor = svga_tilecursor,
+};
+
+static struct fb_tile_ops s3fb_fast_tile_ops = {
+ .fb_settile = s3fb_settile_fast,
+ .fb_tilecopy = svga_tilecopy,
+ .fb_tilefill = svga_tilefill,
+ .fb_tileblit = svga_tileblit,
+ .fb_tilecursor = svga_tilecursor,
+};
+
+
+/* ------------------------------------------------------------------------- */
+
+/* image data is MSB-first, fb structure is MSB-first too */
+static inline u32 expand_color(u32 c)
+{
+ return ((c & 1) | ((c & 2) << 7) | ((c & 4) << 14) | ((c & 8) << 21)) * 0xFF;
+}
+
+/* s3fb_iplan_imageblit silently assumes that almost everything is 8-pixel aligned */
+static void s3fb_iplan_imageblit(struct fb_info *info, const struct fb_image *image)
+{
+ u32 fg = expand_color(image->fg_color);
+ u32 bg = expand_color(image->bg_color);
+ const u8 *src1, *src;
+ u8 __iomem *dst1;
+ u32 __iomem *dst;
+ u32 val;
+ int x, y;
+
+ src1 = image->data;
+ dst1 = info->screen_base + (image->dy * info->fix.line_length)
+ + ((image->dx / 8) * 4);
+
+ for (y = 0; y < image->height; y++) {
+ src = src1;
+ dst = (u32 __iomem *) dst1;
+ for (x = 0; x < image->width; x += 8) {
+ val = *(src++) * 0x01010101;
+ val = (val & fg) | (~val & bg);
+ fb_writel(val, dst++);
+ }
+ src1 += image->width / 8;
+ dst1 += info->fix.line_length;
+ }
+
+}
+
+/* s3fb_iplan_fillrect silently assumes that almost everything is 8-pixel aligned */
+static void s3fb_iplan_fillrect(struct fb_info *info, const struct fb_fillrect *rect)
+{
+ u32 fg = expand_color(rect->color);
+ u8 __iomem *dst1;
+ u32 __iomem *dst;
+ int x, y;
+
+ dst1 = info->screen_base + (rect->dy * info->fix.line_length)
+ + ((rect->dx / 8) * 4);
+
+ for (y = 0; y < rect->height; y++) {
+ dst = (u32 __iomem *) dst1;
+ for (x = 0; x < rect->width; x += 8) {
+ fb_writel(fg, dst++);
+ }
+ dst1 += info->fix.line_length;
+ }
+}
+
+
+/* image data is MSB-first, fb structure is high-nibble-in-low-byte-first */
+static inline u32 expand_pixel(u32 c)
+{
+ return (((c & 1) << 24) | ((c & 2) << 27) | ((c & 4) << 14) | ((c & 8) << 17) |
+ ((c & 16) << 4) | ((c & 32) << 7) | ((c & 64) >> 6) | ((c & 128) >> 3)) * 0xF;
+}
+
+/* s3fb_cfb4_imageblit silently assumes that almost everything is 8-pixel aligned */
+static void s3fb_cfb4_imageblit(struct fb_info *info, const struct fb_image *image)
+{
+ u32 fg = image->fg_color * 0x11111111;
+ u32 bg = image->bg_color * 0x11111111;
+ const u8 *src1, *src;
+ u8 __iomem *dst1;
+ u32 __iomem *dst;
+ u32 val;
+ int x, y;
+
+ src1 = image->data;
+ dst1 = info->screen_base + (image->dy * info->fix.line_length)
+ + ((image->dx / 8) * 4);
+
+ for (y = 0; y < image->height; y++) {
+ src = src1;
+ dst = (u32 __iomem *) dst1;
+ for (x = 0; x < image->width; x += 8) {
+ val = expand_pixel(*(src++));
+ val = (val & fg) | (~val & bg);
+ fb_writel(val, dst++);
+ }
+ src1 += image->width / 8;
+ dst1 += info->fix.line_length;
+ }
+}
+
+static void s3fb_imageblit(struct fb_info *info, const struct fb_image *image)
+{
+ if ((info->var.bits_per_pixel == 4) && (image->depth == 1)
+ && ((image->width % 8) == 0) && ((image->dx % 8) == 0)) {
+ if (info->fix.type == FB_TYPE_INTERLEAVED_PLANES)
+ s3fb_iplan_imageblit(info, image);
+ else
+ s3fb_cfb4_imageblit(info, image);
+ } else
+ cfb_imageblit(info, image);
+}
+
+static void s3fb_fillrect(struct fb_info *info, const struct fb_fillrect *rect)
+{
+ if ((info->var.bits_per_pixel == 4)
+ && ((rect->width % 8) == 0) && ((rect->dx % 8) == 0)
+ && (info->fix.type == FB_TYPE_INTERLEAVED_PLANES))
+ s3fb_iplan_fillrect(info, rect);
+ else
+ cfb_fillrect(info, rect);
+}
+
+
+
+/* ------------------------------------------------------------------------- */
+
+
+static void s3_set_pixclock(struct fb_info *info, u32 pixclock)
+{
+ u16 m, n, r;
+ u8 regval;
+
+ svga_compute_pll(&s3_pll, 1000000000 / pixclock, &m, &n, &r, info->node);
+
+ /* Set VGA misc register */
+ regval = vga_r(NULL, VGA_MIS_R);
+ vga_w(NULL, VGA_MIS_W, regval | VGA_MIS_ENB_PLL_LOAD);
+
+ /* Set S3 clock registers */
+ vga_wseq(NULL, 0x12, ((n - 2) | (r << 5)));
+ vga_wseq(NULL, 0x13, m - 2);
+
+ udelay(1000);
+
+ /* Activate clock - write 0, 1, 0 to seq/15 bit 5 */
+ regval = vga_rseq (NULL, 0x15); /* | 0x80; */
+ vga_wseq(NULL, 0x15, regval & ~(1<<5));
+ vga_wseq(NULL, 0x15, regval | (1<<5));
+ vga_wseq(NULL, 0x15, regval & ~(1<<5));
+}
+
+
+/* Open framebuffer */
+
+static int s3fb_open(struct fb_info *info, int user)
+{
+ struct s3fb_info *par = info->par;
+
+ mutex_lock(&(par->open_lock));
+ if (par->ref_count == 0) {
+ memset(&(par->state), 0, sizeof(struct vgastate));
+ par->state.flags = VGA_SAVE_MODE | VGA_SAVE_FONTS | VGA_SAVE_CMAP;
+ par->state.num_crtc = 0x70;
+ par->state.num_seq = 0x20;
+ save_vga(&(par->state));
+ }
+
+ par->ref_count++;
+ mutex_unlock(&(par->open_lock));
+
+ return 0;
+}
+
+/* Close framebuffer */
+
+static int s3fb_release(struct fb_info *info, int user)
+{
+ struct s3fb_info *par = info->par;
+
+ mutex_lock(&(par->open_lock));
+ if (par->ref_count == 0) {
+ mutex_unlock(&(par->open_lock));
+ return -EINVAL;
+ }
+
+ if (par->ref_count == 1)
+ restore_vga(&(par->state));
+
+ par->ref_count--;
+ mutex_unlock(&(par->open_lock));
+
+ return 0;
+}
+
+/* Validate passed in var */
+
+static int s3fb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
+{
+ struct s3fb_info *par = info->par;
+ int rv, mem, step;
+
+ /* Find appropriate format */
+ rv = svga_match_format (s3fb_formats, var, NULL);
+ if ((rv < 0) || ((par->chip == CHIP_988_VIRGE_VX) ? (rv == 7) : (rv == 6)))
+ { /* 24bpp on VIRGE VX, 32bpp on others */
+ printk(KERN_ERR "fb%d: unsupported mode requested\n", info->node);
+ return rv;
+ }
+
+ /* Do not allow to have real resoulution larger than virtual */
+ if (var->xres > var->xres_virtual)
+ var->xres_virtual = var->xres;
+
+ if (var->yres > var->yres_virtual)
+ var->yres_virtual = var->yres;
+
+ /* Round up xres_virtual to have proper alignment of lines */
+ step = s3fb_formats[rv].xresstep - 1;
+ var->xres_virtual = (var->xres_virtual+step) & ~step;
+
+ /* Check whether have enough memory */
+ mem = ((var->bits_per_pixel * var->xres_virtual) >> 3) * var->yres_virtual;
+ if (mem > info->screen_size)
+ {
+ printk(KERN_ERR "fb%d: not enough framebuffer memory (%d kB requested , %d kB available)\n",
+ info->node, mem >> 10, (unsigned int) (info->screen_size >> 10));
+ return -EINVAL;
+ }
+
+ rv = svga_check_timings (&s3_timing_regs, var, info->node);
+ if (rv < 0)
+ {
+ printk(KERN_ERR "fb%d: invalid timings requested\n", info->node);
+ return rv;
+ }
+
+ return 0;
+}
+
+/* Set video mode from par */
+
+static int s3fb_set_par(struct fb_info *info)
+{
+ struct s3fb_info *par = info->par;
+ u32 value, mode, hmul, offset_value, screen_size, multiplex;
+ u32 bpp = info->var.bits_per_pixel;
+
+ if (bpp != 0) {
+ info->fix.ypanstep = 1;
+ info->fix.line_length = (info->var.xres_virtual * bpp) / 8;
+
+ info->flags &= ~FBINFO_MISC_TILEBLITTING;
+ info->tileops = NULL;
+
+ offset_value = (info->var.xres_virtual * bpp) / 64;
+ screen_size = info->var.yres_virtual * info->fix.line_length;
+ } else {
+ info->fix.ypanstep = 16;
+ info->fix.line_length = 0;
+
+ info->flags |= FBINFO_MISC_TILEBLITTING;
+ info->tileops = fasttext ? &s3fb_fast_tile_ops : &s3fb_tile_ops;
+
+ offset_value = info->var.xres_virtual / 16;
+ screen_size = (info->var.xres_virtual * info->var.yres_virtual) / 64;
+ }
+
+ info->var.xoffset = 0;
+ info->var.yoffset = 0;
+ info->var.activate = FB_ACTIVATE_NOW;
+
+ /* Unlock registers */
+ vga_wcrt(NULL, 0x38, 0x48);
+ vga_wcrt(NULL, 0x39, 0xA5);
+ vga_wseq(NULL, 0x08, 0x06);
+ svga_wcrt_mask(0x11, 0x00, 0x80);
+
+ /* Blank screen and turn off sync */
+ svga_wseq_mask(0x01, 0x20, 0x20);
+ svga_wcrt_mask(0x17, 0x00, 0x80);
+
+ /* Set default values */
+ svga_set_default_gfx_regs();
+ svga_set_default_atc_regs();
+ svga_set_default_seq_regs();
+ svga_set_default_crt_regs();
+ svga_wcrt_multi(s3_line_compare_regs, 0xFFFFFFFF);
+ svga_wcrt_multi(s3_start_address_regs, 0);
+
+ /* S3 specific initialization */
+ svga_wcrt_mask(0x58, 0x10, 0x10); /* enable linear framebuffer */
+ svga_wcrt_mask(0x31, 0x08, 0x08); /* enable sequencer access to framebuffer above 256 kB */
+
+/* svga_wcrt_mask(0x33, 0x08, 0x08); */ /* DDR ? */
+/* svga_wcrt_mask(0x43, 0x01, 0x01); */ /* DDR ? */
+ svga_wcrt_mask(0x33, 0x00, 0x08); /* no DDR ? */
+ svga_wcrt_mask(0x43, 0x00, 0x01); /* no DDR ? */
+
+ svga_wcrt_mask(0x5D, 0x00, 0x28); // Clear strange HSlen bits
+
+/* svga_wcrt_mask(0x58, 0x03, 0x03); */
+
+/* svga_wcrt_mask(0x53, 0x12, 0x13); */ /* enable MMIO */
+/* svga_wcrt_mask(0x40, 0x08, 0x08); */ /* enable write buffer */
+
+
+ /* Set the offset register */
+ pr_debug("fb%d: offset register : %d\n", info->node, offset_value);
+ svga_wcrt_multi(s3_offset_regs, offset_value);
+
+ vga_wcrt(NULL, 0x54, 0x18); /* M parameter */
+ vga_wcrt(NULL, 0x60, 0xff); /* N parameter */
+ vga_wcrt(NULL, 0x61, 0xff); /* L parameter */
+ vga_wcrt(NULL, 0x62, 0xff); /* L parameter */
+
+ vga_wcrt(NULL, 0x3A, 0x35);
+ svga_wattr(0x33, 0x00);
+
+ if (info->var.vmode & FB_VMODE_DOUBLE)
+ svga_wcrt_mask(0x09, 0x80, 0x80);
+ else
+ svga_wcrt_mask(0x09, 0x00, 0x80);
+
+ if (info->var.vmode & FB_VMODE_INTERLACED)
+ svga_wcrt_mask(0x42, 0x20, 0x20);
+ else
+ svga_wcrt_mask(0x42, 0x00, 0x20);
+
+ /* Disable hardware graphics cursor */
+ svga_wcrt_mask(0x45, 0x00, 0x01);
+ /* Disable Streams engine */
+ svga_wcrt_mask(0x67, 0x00, 0x0C);
+
+ mode = svga_match_format(s3fb_formats, &(info->var), &(info->fix));
+
+ /* S3 virge DX hack */
+ if (par->chip == CHIP_375_VIRGE_DX) {
+ vga_wcrt(NULL, 0x86, 0x80);
+ vga_wcrt(NULL, 0x90, 0x00);
+ }
+
+ /* S3 virge VX hack */
+ if (par->chip == CHIP_988_VIRGE_VX) {
+ vga_wcrt(NULL, 0x50, 0x00);
+ vga_wcrt(NULL, 0x67, 0x50);
+
+ vga_wcrt(NULL, 0x63, (mode <= 2) ? 0x90 : 0x09);
+ vga_wcrt(NULL, 0x66, 0x90);
+ }
+
+ svga_wcrt_mask(0x31, 0x00, 0x40);
+ multiplex = 0;
+ hmul = 1;
+
+ /* Set mode-specific register values */
+ switch (mode) {
+ case 0:
+ pr_debug("fb%d: text mode\n", info->node);
+ svga_set_textmode_vga_regs();
+
+ /* Set additional registers like in 8-bit mode */
+ svga_wcrt_mask(0x50, 0x00, 0x30);
+ svga_wcrt_mask(0x67, 0x00, 0xF0);
+
+ /* Disable enhanced mode */
+ svga_wcrt_mask(0x3A, 0x00, 0x30);
+
+ if (fasttext) {
+ pr_debug("fb%d: high speed text mode set\n", info->node);
+ svga_wcrt_mask(0x31, 0x40, 0x40);
+ }
+ break;
+ case 1:
+ pr_debug("fb%d: 4 bit pseudocolor\n", info->node);
+ vga_wgfx(NULL, VGA_GFX_MODE, 0x40);
+
+ /* Set additional registers like in 8-bit mode */
+ svga_wcrt_mask(0x50, 0x00, 0x30);
+ svga_wcrt_mask(0x67, 0x00, 0xF0);
+
+ /* disable enhanced mode */
+ svga_wcrt_mask(0x3A, 0x00, 0x30);
+ break;
+ case 2:
+ pr_debug("fb%d: 4 bit pseudocolor, planar\n", info->node);
+
+ /* Set additional registers like in 8-bit mode */
+ svga_wcrt_mask(0x50, 0x00, 0x30);
+ svga_wcrt_mask(0x67, 0x00, 0xF0);
+
+ /* disable enhanced mode */
+ svga_wcrt_mask(0x3A, 0x00, 0x30);
+ break;
+ case 3:
+ pr_debug("fb%d: 8 bit pseudocolor\n", info->node);
+ if (info->var.pixclock > 20000) {
+ svga_wcrt_mask(0x50, 0x00, 0x30);
+ svga_wcrt_mask(0x67, 0x00, 0xF0);
+ } else {
+ svga_wcrt_mask(0x50, 0x00, 0x30);
+ svga_wcrt_mask(0x67, 0x10, 0xF0);
+ multiplex = 1;
+ }
+ break;
+ case 4:
+ pr_debug("fb%d: 5/5/5 truecolor\n", info->node);
+ if (par->chip == CHIP_988_VIRGE_VX) {
+ if (info->var.pixclock > 20000)
+ svga_wcrt_mask(0x67, 0x20, 0xF0);
+ else
+ svga_wcrt_mask(0x67, 0x30, 0xF0);
+ } else {
+ svga_wcrt_mask(0x50, 0x10, 0x30);
+ svga_wcrt_mask(0x67, 0x30, 0xF0);
+ hmul = 2;
+ }
+ break;
+ case 5:
+ pr_debug("fb%d: 5/6/5 truecolor\n", info->node);
+ if (par->chip == CHIP_988_VIRGE_VX) {
+ if (info->var.pixclock > 20000)
+ svga_wcrt_mask(0x67, 0x40, 0xF0);
+ else
+ svga_wcrt_mask(0x67, 0x50, 0xF0);
+ } else {
+ svga_wcrt_mask(0x50, 0x10, 0x30);
+ svga_wcrt_mask(0x67, 0x50, 0xF0);
+ hmul = 2;
+ }
+ break;
+ case 6:
+ /* VIRGE VX case */
+ pr_debug("fb%d: 8/8/8 truecolor\n", info->node);
+ svga_wcrt_mask(0x67, 0xD0, 0xF0);
+ break;
+ case 7:
+ pr_debug("fb%d: 8/8/8/8 truecolor\n", info->node);
+ svga_wcrt_mask(0x50, 0x30, 0x30);
+ svga_wcrt_mask(0x67, 0xD0, 0xF0);
+ break;
+ default:
+ printk(KERN_ERR "fb%d: unsupported mode - bug\n", info->node);
+ return -EINVAL;
+ }
+
+ if (par->chip != CHIP_988_VIRGE_VX) {
+ svga_wseq_mask(0x15, multiplex ? 0x10 : 0x00, 0x10);
+ svga_wseq_mask(0x18, multiplex ? 0x80 : 0x00, 0x80);
+ }
+
+ s3_set_pixclock(info, info->var.pixclock);
+ svga_set_timings(&s3_timing_regs, &(info->var), hmul, 1,
+ (info->var.vmode & FB_VMODE_DOUBLE) ? 2 : 1,
+ (info->var.vmode & FB_VMODE_INTERLACED) ? 2 : 1,
+ hmul, info->node);
+
+ /* Set interlaced mode start/end register */
+ value = info->var.xres + info->var.left_margin + info->var.right_margin + info->var.hsync_len;
+ value = ((value * hmul) / 8) - 5;
+ vga_wcrt(NULL, 0x3C, (value + 1) / 2);
+
+ memset((u8*)info->screen_base, 0x00, screen_size);
+ /* Device and screen back on */
+ svga_wcrt_mask(0x17, 0x80, 0x80);
+ svga_wseq_mask(0x01, 0x00, 0x20);
+
+ return 0;
+}
+
+/* Set a colour register */
+
+static int s3fb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
+ u_int transp, struct fb_info *fb)
+{
+ switch (fb->var.bits_per_pixel) {
+ case 0:
+ case 4:
+ if (regno >= 16)
+ return -EINVAL;
+
+ if ((fb->var.bits_per_pixel == 4) &&
+ (fb->var.nonstd == 0)) {
+ outb(0xF0, VGA_PEL_MSK);
+ outb(regno*16, VGA_PEL_IW);
+ } else {
+ outb(0x0F, VGA_PEL_MSK);
+ outb(regno, VGA_PEL_IW);
+ }
+ outb(red >> 10, VGA_PEL_D);
+ outb(green >> 10, VGA_PEL_D);
+ outb(blue >> 10, VGA_PEL_D);
+ break;
+ case 8:
+ if (regno >= 256)
+ return -EINVAL;
+
+ outb(0xFF, VGA_PEL_MSK);
+ outb(regno, VGA_PEL_IW);
+ outb(red >> 10, VGA_PEL_D);
+ outb(green >> 10, VGA_PEL_D);
+ outb(blue >> 10, VGA_PEL_D);
+ break;
+ case 16:
+ if (regno >= 16)
+ return -EINVAL;
+
+ if (fb->var.green.length == 5)
+ ((u32*)fb->pseudo_palette)[regno] = ((red & 0xF800) >> 1) |
+ ((green & 0xF800) >> 6) | ((blue & 0xF800) >> 11);
+ else if (fb->var.green.length == 6)
+ ((u32*)fb->pseudo_palette)[regno] = (red & 0xF800) |
+ ((green & 0xFC00) >> 5) | ((blue & 0xF800) >> 11);
+ else return -EINVAL;
+ break;
+ case 24:
+ case 32:
+ if (regno >= 16)
+ return -EINVAL;
+
+ ((u32*)fb->pseudo_palette)[regno] = ((transp & 0xFF00) << 16) | ((red & 0xFF00) << 8) |
+ (green & 0xFF00) | ((blue & 0xFF00) >> 8);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+
+/* Set the display blanking state */
+
+static int s3fb_blank(int blank_mode, struct fb_info *info)
+{
+ switch (blank_mode) {
+ case FB_BLANK_UNBLANK:
+ pr_debug("fb%d: unblank\n", info->node);
+ svga_wcrt_mask(0x56, 0x00, 0x06);
+ svga_wseq_mask(0x01, 0x00, 0x20);
+ break;
+ case FB_BLANK_NORMAL:
+ pr_debug("fb%d: blank\n", info->node);
+ svga_wcrt_mask(0x56, 0x00, 0x06);
+ svga_wseq_mask(0x01, 0x20, 0x20);
+ break;
+ case FB_BLANK_HSYNC_SUSPEND:
+ pr_debug("fb%d: hsync\n", info->node);
+ svga_wcrt_mask(0x56, 0x02, 0x06);
+ svga_wseq_mask(0x01, 0x20, 0x20);
+ break;
+ case FB_BLANK_VSYNC_SUSPEND:
+ pr_debug("fb%d: vsync\n", info->node);
+ svga_wcrt_mask(0x56, 0x04, 0x06);
+ svga_wseq_mask(0x01, 0x20, 0x20);
+ break;
+ case FB_BLANK_POWERDOWN:
+ pr_debug("fb%d: sync down\n", info->node);
+ svga_wcrt_mask(0x56, 0x06, 0x06);
+ svga_wseq_mask(0x01, 0x20, 0x20);
+ break;
+ }
+
+ return 0;
+}
+
+
+/* Pan the display */
+
+static int s3fb_pan_display(struct fb_var_screeninfo *var, struct fb_info *info) {
+
+ unsigned int offset;
+
+ /* Validate the offsets */
+ if ((var->xoffset + var->xres) > var->xres_virtual)
+ return -EINVAL;
+ if ((var->yoffset + var->yres) > var->yres_virtual)
+ return -EINVAL;
+
+ /* Calculate the offset */
+ if (var->bits_per_pixel == 0) {
+ offset = (var->yoffset / 16) * (var->xres_virtual / 2) + (var->xoffset / 2);
+ offset = offset >> 2;
+ } else {
+ offset = (var->yoffset * info->fix.line_length) +
+ (var->xoffset * var->bits_per_pixel / 8);
+ offset = offset >> 2;
+ }
+
+ /* Set the offset */
+ svga_wcrt_multi(s3_start_address_regs, offset);
+
+ return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+/* Frame buffer operations */
+
+static struct fb_ops s3fb_ops = {
+ .owner = THIS_MODULE,
+ .fb_open = s3fb_open,
+ .fb_release = s3fb_release,
+ .fb_check_var = s3fb_check_var,
+ .fb_set_par = s3fb_set_par,
+ .fb_setcolreg = s3fb_setcolreg,
+ .fb_blank = s3fb_blank,
+ .fb_pan_display = s3fb_pan_display,
+ .fb_fillrect = s3fb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = s3fb_imageblit,
+};
+
+/* ------------------------------------------------------------------------- */
+
+static int __devinit s3_identification(int chip)
+{
+ if (chip == CHIP_XXX_TRIO) {
+ u8 cr30 = vga_rcrt(NULL, 0x30);
+ u8 cr2e = vga_rcrt(NULL, 0x2e);
+ u8 cr2f = vga_rcrt(NULL, 0x2f);
+
+ if ((cr30 == 0xE0) || (cr30 == 0xE1)) {
+ if (cr2e == 0x10)
+ return CHIP_732_TRIO32;
+ if (cr2e == 0x11) {
+ if (! (cr2f & 0x40))
+ return CHIP_764_TRIO64;
+ else
+ return CHIP_765_TRIO64VP;
+ }
+ }
+ }
+
+ if (chip == CHIP_XXX_TRIO64V2_DXGX) {
+ u8 cr6f = vga_rcrt(NULL, 0x6f);
+
+ if (! (cr6f & 0x01))
+ return CHIP_775_TRIO64V2_DX;
+ else
+ return CHIP_785_TRIO64V2_GX;
+ }
+
+ if (chip == CHIP_XXX_VIRGE_DXGX) {
+ u8 cr6f = vga_rcrt(NULL, 0x6f);
+
+ if (! (cr6f & 0x01))
+ return CHIP_375_VIRGE_DX;
+ else
+ return CHIP_385_VIRGE_GX;
+ }
+
+ return CHIP_UNKNOWN;
+}
+
+
+/* PCI probe */
+
+static int __devinit s3_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ struct fb_info *info;
+ struct s3fb_info *par;
+ int rc;
+ u8 regval, cr38, cr39;
+
+ /* Ignore secondary VGA device because there is no VGA arbitration */
+ if (! svga_primary_device(dev)) {
+ dev_info(&(dev->dev), "ignoring secondary device\n");
+ return -ENODEV;
+ }
+
+ /* Allocate and fill driver data structure */
+ info = framebuffer_alloc(sizeof(struct s3fb_info), NULL);
+ if (!info) {
+ dev_err(&(dev->dev), "cannot allocate memory\n");
+ return -ENOMEM;
+ }
+
+ par = info->par;
+ mutex_init(&par->open_lock);
+
+ info->flags = FBINFO_PARTIAL_PAN_OK | FBINFO_HWACCEL_YPAN;
+ info->fbops = &s3fb_ops;
+
+ /* Prepare PCI device */
+ rc = pci_enable_device(dev);
+ if (rc < 0) {
+ dev_err(&(dev->dev), "cannot enable PCI device\n");
+ goto err_enable_device;
+ }
+
+ rc = pci_request_regions(dev, "s3fb");
+ if (rc < 0) {
+ dev_err(&(dev->dev), "cannot reserve framebuffer region\n");
+ goto err_request_regions;
+ }
+
+
+ info->fix.smem_start = pci_resource_start(dev, 0);
+ info->fix.smem_len = pci_resource_len(dev, 0);
+
+ /* Map physical IO memory address into kernel space */
+ info->screen_base = pci_iomap(dev, 0, 0);
+ if (! info->screen_base) {
+ rc = -ENOMEM;
+ dev_err(&(dev->dev), "iomap for framebuffer failed\n");
+ goto err_iomap;
+ }
+
+ /* Unlock regs */
+ cr38 = vga_rcrt(NULL, 0x38);
+ cr39 = vga_rcrt(NULL, 0x39);
+ vga_wseq(NULL, 0x08, 0x06);
+ vga_wcrt(NULL, 0x38, 0x48);
+ vga_wcrt(NULL, 0x39, 0xA5);
+
+ /* Find how many physical memory there is on card */
+ /* 0x36 register is accessible even if other registers are locked */
+ regval = vga_rcrt(NULL, 0x36);
+ info->screen_size = s3_memsizes[regval >> 5] << 10;
+ info->fix.smem_len = info->screen_size;
+
+ par->chip = id->driver_data & CHIP_MASK;
+ par->rev = vga_rcrt(NULL, 0x2f);
+ if (par->chip & CHIP_UNDECIDED_FLAG)
+ par->chip = s3_identification(par->chip);
+
+ /* Find MCLK frequency */
+ regval = vga_rseq(NULL, 0x10);
+ par->mclk_freq = ((vga_rseq(NULL, 0x11) + 2) * 14318) / ((regval & 0x1F) + 2);
+ par->mclk_freq = par->mclk_freq >> (regval >> 5);
+
+ /* Restore locks */
+ vga_wcrt(NULL, 0x38, cr38);
+ vga_wcrt(NULL, 0x39, cr39);
+
+ strcpy(info->fix.id, s3_names [par->chip]);
+ info->fix.mmio_start = 0;
+ info->fix.mmio_len = 0;
+ info->fix.type = FB_TYPE_PACKED_PIXELS;
+ info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
+ info->fix.ypanstep = 0;
+ info->fix.accel = FB_ACCEL_NONE;
+ info->pseudo_palette = (void*) (par->pseudo_palette);
+
+ /* Prepare startup mode */
+ rc = fb_find_mode(&(info->var), info, mode, NULL, 0, NULL, 8);
+ if (! ((rc == 1) || (rc == 2))) {
+ rc = -EINVAL;
+ dev_err(&(dev->dev), "mode %s not found\n", mode);
+ goto err_find_mode;
+ }
+
+ rc = fb_alloc_cmap(&info->cmap, 256, 0);
+ if (rc < 0) {
+ dev_err(&(dev->dev), "cannot allocate colormap\n");
+ goto err_alloc_cmap;
+ }
+
+ rc = register_framebuffer(info);
+ if (rc < 0) {
+ dev_err(&(dev->dev), "cannot register framebugger\n");
+ goto err_reg_fb;
+ }
+
+ printk(KERN_INFO "fb%d: %s on %s, %d MB RAM, %d MHz MCLK\n", info->node, info->fix.id,
+ pci_name(dev), info->fix.smem_len >> 20, (par->mclk_freq + 500) / 1000);
+
+ if (par->chip == CHIP_UNKNOWN)
+ printk(KERN_INFO "fb%d: unknown chip, CR2D=%x, CR2E=%x, CRT2F=%x, CRT30=%x\n",
+ info->node, vga_rcrt(NULL, 0x2d), vga_rcrt(NULL, 0x2e),
+ vga_rcrt(NULL, 0x2f), vga_rcrt(NULL, 0x30));
+
+ /* Record a reference to the driver data */
+ pci_set_drvdata(dev, info);
+
+#ifdef CONFIG_MTRR
+ if (mtrr) {
+ par->mtrr_reg = -1;
+ par->mtrr_reg = mtrr_add(info->fix.smem_start, info->fix.smem_len, MTRR_TYPE_WRCOMB, 1);
+ }
+#endif
+
+ return 0;
+
+ /* Error handling */
+err_reg_fb:
+ fb_dealloc_cmap(&info->cmap);
+err_alloc_cmap:
+err_find_mode:
+ pci_iounmap(dev, info->screen_base);
+err_iomap:
+ pci_release_regions(dev);
+err_request_regions:
+/* pci_disable_device(dev); */
+err_enable_device:
+ framebuffer_release(info);
+ return rc;
+}
+
+
+/* PCI remove */
+
+static void __devexit s3_pci_remove(struct pci_dev *dev)
+{
+ struct fb_info *info = pci_get_drvdata(dev);
+ struct s3fb_info *par = info->par;
+
+ if (info) {
+
+#ifdef CONFIG_MTRR
+ if (par->mtrr_reg >= 0) {
+ mtrr_del(par->mtrr_reg, 0, 0);
+ par->mtrr_reg = -1;
+ }
+#endif
+
+ unregister_framebuffer(info);
+ fb_dealloc_cmap(&info->cmap);
+
+ pci_iounmap(dev, info->screen_base);
+ pci_release_regions(dev);
+/* pci_disable_device(dev); */
+
+ pci_set_drvdata(dev, NULL);
+ framebuffer_release(info);
+ }
+}
+
+/* PCI suspend */
+
+static int s3_pci_suspend(struct pci_dev* dev, pm_message_t state)
+{
+ struct fb_info *info = pci_get_drvdata(dev);
+ struct s3fb_info *par = info->par;
+
+ dev_info(&(dev->dev), "suspend\n");
+
+ acquire_console_sem();
+ mutex_lock(&(par->open_lock));
+
+ if ((state.event == PM_EVENT_FREEZE) || (par->ref_count == 0)) {
+ mutex_unlock(&(par->open_lock));
+ release_console_sem();
+ return 0;
+ }
+
+ fb_set_suspend(info, 1);
+
+ pci_save_state(dev);
+ pci_disable_device(dev);
+ pci_set_power_state(dev, pci_choose_state(dev, state));
+
+ mutex_unlock(&(par->open_lock));
+ release_console_sem();
+
+ return 0;
+}
+
+
+/* PCI resume */
+
+static int s3_pci_resume(struct pci_dev* dev)
+{
+ struct fb_info *info = pci_get_drvdata(dev);
+ struct s3fb_info *par = info->par;
+
+ dev_info(&(dev->dev), "resume\n");
+
+ acquire_console_sem();
+ mutex_lock(&(par->open_lock));
+
+ if (par->ref_count == 0) {
+ mutex_unlock(&(par->open_lock));
+ release_console_sem();
+ return 0;
+ }
+
+ pci_set_power_state(dev, PCI_D0);
+ pci_restore_state(dev);
+ pci_enable_device(dev);
+ pci_set_master(dev);
+
+ s3fb_set_par(info);
+ fb_set_suspend(info, 0);
+
+ mutex_unlock(&(par->open_lock));
+ release_console_sem();
+
+ return 0;
+}
+
+
+/* List of boards that we are trying to support */
+
+static struct pci_device_id s3_devices[] __devinitdata = {
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8810), .driver_data = CHIP_XXX_TRIO},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8811), .driver_data = CHIP_XXX_TRIO},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8812), .driver_data = CHIP_M65_AURORA64VP},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8814), .driver_data = CHIP_767_TRIO64UVP},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8901), .driver_data = CHIP_XXX_TRIO64V2_DXGX},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8902), .driver_data = CHIP_551_PLATO_PX},
+
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x5631), .driver_data = CHIP_325_VIRGE},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x883D), .driver_data = CHIP_988_VIRGE_VX},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8A01), .driver_data = CHIP_XXX_VIRGE_DXGX},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8A10), .driver_data = CHIP_356_VIRGE_GX2},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8A11), .driver_data = CHIP_357_VIRGE_GX2P},
+ {PCI_DEVICE(PCI_VENDOR_ID_S3, 0x8A12), .driver_data = CHIP_359_VIRGE_GX2P},
+
+ {0, 0, 0, 0, 0, 0, 0}
+};
+
+
+MODULE_DEVICE_TABLE(pci, s3_devices);
+
+static struct pci_driver s3fb_pci_driver = {
+ .name = "s3fb",
+ .id_table = s3_devices,
+ .probe = s3_pci_probe,
+ .remove = __devexit_p(s3_pci_remove),
+ .suspend = s3_pci_suspend,
+ .resume = s3_pci_resume,
+};
+
+/* Parse user speficied options */
+
+#ifndef MODULE
+static int __init s3fb_setup(char *options)
+{
+ char *opt;
+
+ if (!options || !*options)
+ return 0;
+
+ while ((opt = strsep(&options, ",")) != NULL) {
+
+ if (!*opt)
+ continue;
+#ifdef CONFIG_MTRR
+ else if (!strcmp(opt, "mtrr:"))
+ mtrr = simple_strtoul(opt + 5, NULL, 0);
+#endif
+ else if (!strcmp(opt, "fasttext:"))
+ mtrr = simple_strtoul(opt + 9, NULL, 0);
+ else
+ mode = opt;
+ }
+
+ return 0;
+}
+#endif
+
+/* Cleanup */
+
+static void __exit s3fb_cleanup(void)
+{
+ pr_debug("s3fb: cleaning up\n");
+ pci_unregister_driver(&s3fb_pci_driver);
+}
+
+/* Driver Initialisation */
+
+static int __init s3fb_init(void)
+{
+
+#ifndef MODULE
+ char *option = NULL;
+
+ if (fb_get_options("s3fb", &option))
+ return -ENODEV;
+ s3fb_setup(option);
+#endif
+
+ pr_debug("s3fb: initializing\n");
+ return pci_register_driver(&s3fb_pci_driver);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/* Modularization */
+
+module_init(s3fb_init);
+module_exit(s3fb_cleanup);
diff -uprN -X linux-2.6.20-x/Documentation/dontdiff linux-2.6.20-x/drivers/video/svgalib.c linux-2.6.20-s3fb/drivers/video/svgalib.c
--- linux-2.6.20-x/drivers/video/svgalib.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.20-s3fb/drivers/video/svgalib.c 2007-02-09 14:28:50.000000000 +0100
@@ -0,0 +1,631 @@
+/*
+ * Common utility functions for VGA-based graphics cards.
+ *
+ * Copyright (c) 2006-2007 Ondrej Zajicek <santiago@...reenet.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ *
+ * Some parts are based on David Boucher's viafb (http://davesdomain.org.uk/viafb/)
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/fb.h>
+#include <linux/svga.h>
+#include <linux/slab.h>
+#include <asm/types.h>
+#include <asm/io.h>
+
+
+/* Write a CRT register value spread across multiple registers */
+void svga_wcrt_multi(const struct vga_regset *regset, u32 value) {
+
+ u8 regval, bitval, bitnum;
+
+ while (regset->regnum != VGA_REGSET_END_VAL) {
+ regval = vga_rcrt(NULL, regset->regnum);
+ bitnum = regset->lowbit;
+ while (bitnum <= regset->highbit) {
+ bitval = 1 << bitnum;
+ regval = regval & ~bitval;
+ if (value & 1) regval = regval | bitval;
+ bitnum ++;
+ value = value >> 1;
+ }
+ vga_wcrt(NULL, regset->regnum, regval);
+ regset ++;
+ }
+}
+
+/* Write a sequencer register value spread across multiple registers */
+void svga_wseq_multi(const struct vga_regset *regset, u32 value) {
+
+ u8 regval, bitval, bitnum;
+
+ while (regset->regnum != VGA_REGSET_END_VAL) {
+ regval = vga_rseq(NULL, regset->regnum);
+ bitnum = regset->lowbit;
+ while (bitnum <= regset->highbit) {
+ bitval = 1 << bitnum;
+ regval = regval & ~bitval;
+ if (value & 1) regval = regval | bitval;
+ bitnum ++;
+ value = value >> 1;
+ }
+ vga_wseq(NULL, regset->regnum, regval);
+ regset ++;
+ }
+}
+
+static unsigned int svga_regset_size(const struct vga_regset *regset)
+{
+ u8 count = 0;
+
+ while (regset->regnum != VGA_REGSET_END_VAL) {
+ count += regset->highbit - regset->lowbit + 1;
+ regset ++;
+ }
+ return 1 << count;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+
+/* Set graphics controller registers to sane values */
+void svga_set_default_gfx_regs(void)
+{
+ /* All standard GFX registers (GR00 - GR08) */
+ vga_wgfx(NULL, VGA_GFX_SR_VALUE, 0x00);
+ vga_wgfx(NULL, VGA_GFX_SR_ENABLE, 0x00);
+ vga_wgfx(NULL, VGA_GFX_COMPARE_VALUE, 0x00);
+ vga_wgfx(NULL, VGA_GFX_DATA_ROTATE, 0x00);
+ vga_wgfx(NULL, VGA_GFX_PLANE_READ, 0x00);
+ vga_wgfx(NULL, VGA_GFX_MODE, 0x00);
+/* vga_wgfx(NULL, VGA_GFX_MODE, 0x20); */
+/* vga_wgfx(NULL, VGA_GFX_MODE, 0x40); */
+ vga_wgfx(NULL, VGA_GFX_MISC, 0x05);
+/* vga_wgfx(NULL, VGA_GFX_MISC, 0x01); */
+ vga_wgfx(NULL, VGA_GFX_COMPARE_MASK, 0x0F);
+ vga_wgfx(NULL, VGA_GFX_BIT_MASK, 0xFF);
+}
+
+/* Set attribute controller registers to sane values */
+void svga_set_default_atc_regs(void)
+{
+ vga_r(NULL, 0x3DA);
+ vga_w(NULL, VGA_ATT_W, 0x00);
+
+ /* All standard ATC registers (AR00 - AR14) */
+ u8 count;
+ for (count = 0; count <= 0xF; count ++)
+ svga_wattr(count, count);
+
+ svga_wattr(VGA_ATC_MODE, 0x01);
+/* svga_wattr(VGA_ATC_MODE, 0x41); */
+ svga_wattr(VGA_ATC_OVERSCAN, 0x00);
+ svga_wattr(VGA_ATC_PLANE_ENABLE, 0x0F);
+ svga_wattr(VGA_ATC_PEL, 0x00);
+ svga_wattr(VGA_ATC_COLOR_PAGE, 0x00);
+
+ vga_r(NULL, 0x3DA);
+ vga_w(NULL, VGA_ATT_W, 0x20);
+}
+
+/* Set sequencer registers to sane values */
+void svga_set_default_seq_regs(void)
+{
+ /* Standard sequencer registers (SR01 - SR04), SR00 is not set */
+ vga_wseq(NULL, VGA_SEQ_CLOCK_MODE, VGA_SR01_CHAR_CLK_8DOTS);
+ vga_wseq(NULL, VGA_SEQ_PLANE_WRITE, VGA_SR02_ALL_PLANES);
+ vga_wseq(NULL, VGA_SEQ_CHARACTER_MAP, 0x00);
+/* vga_wseq(NULL, VGA_SEQ_MEMORY_MODE, VGA_SR04_EXT_MEM | VGA_SR04_SEQ_MODE | VGA_SR04_CHN_4M); */
+ vga_wseq(NULL, VGA_SEQ_MEMORY_MODE, VGA_SR04_EXT_MEM | VGA_SR04_SEQ_MODE);
+}
+
+/* Set CRTC registers to sane values */
+void svga_set_default_crt_regs(void)
+{
+ /* Standard CRT registers CR03 CR08 CR09 CR14 CR17 */
+ svga_wcrt_mask(0x03, 0x80, 0x80); /* Enable vertical retrace EVRA */
+ vga_wcrt(NULL, VGA_CRTC_PRESET_ROW, 0);
+ svga_wcrt_mask(VGA_CRTC_MAX_SCAN, 0, 0x1F);
+ vga_wcrt(NULL, VGA_CRTC_UNDERLINE, 0);
+ vga_wcrt(NULL, VGA_CRTC_MODE, 0xE3);
+}
+
+void svga_set_textmode_vga_regs(void)
+{
+ /* svga_wseq_mask(0x1, 0x00, 0x01); */ /* Switch 8/9 pixel per char */
+ vga_wseq(NULL, VGA_SEQ_MEMORY_MODE, VGA_SR04_EXT_MEM);
+ vga_wseq(NULL, VGA_SEQ_PLANE_WRITE, 0x03);
+
+ vga_wcrt(NULL, VGA_CRTC_MAX_SCAN, 0x0f); /* 0x4f */
+ vga_wcrt(NULL, VGA_CRTC_UNDERLINE, 0x1f);
+ svga_wcrt_mask(VGA_CRTC_MODE, 0x23, 0x7f);
+
+ vga_wcrt(NULL, VGA_CRTC_CURSOR_START, 0x0d);
+ vga_wcrt(NULL, VGA_CRTC_CURSOR_END, 0x0e);
+ vga_wcrt(NULL, VGA_CRTC_CURSOR_HI, 0x00);
+ vga_wcrt(NULL, VGA_CRTC_CURSOR_LO, 0x00);
+
+ vga_wgfx(NULL, VGA_GFX_MODE, 0x10); /* Odd/even memory mode */
+ vga_wgfx(NULL, VGA_GFX_MISC, 0x0E); /* Misc graphics register - text mode enable */
+ vga_wgfx(NULL, VGA_GFX_COMPARE_MASK, 0x00);
+
+ vga_r(NULL, 0x3DA);
+ vga_w(NULL, VGA_ATT_W, 0x00);
+
+ svga_wattr(0x10, 0x0C); /* Attribute Mode Control Register - text mode, blinking and line graphics */
+ svga_wattr(0x13, 0x08); /* Horizontal Pixel Panning Register */
+
+ vga_r(NULL, 0x3DA);
+ vga_w(NULL, VGA_ATT_W, 0x20);
+}
+
+#if 0
+void svga_dump_var(struct fb_var_screeninfo *var, int node)
+{
+ pr_debug("fb%d: var.vmode : 0x%X\n", node, var->vmode);
+ pr_debug("fb%d: var.xres : %d\n", node, var->xres);
+ pr_debug("fb%d: var.yres : %d\n", node, var->yres);
+ pr_debug("fb%d: var.bits_per_pixel: %d\n", node, var->bits_per_pixel);
+ pr_debug("fb%d: var.xres_virtual : %d\n", node, var->xres_virtual);
+ pr_debug("fb%d: var.yres_virtual : %d\n", node, var->yres_virtual);
+ pr_debug("fb%d: var.left_margin : %d\n", node, var->left_margin);
+ pr_debug("fb%d: var.right_margin : %d\n", node, var->right_margin);
+ pr_debug("fb%d: var.upper_margin : %d\n", node, var->upper_margin);
+ pr_debug("fb%d: var.lower_margin : %d\n", node, var->lower_margin);
+ pr_debug("fb%d: var.hsync_len : %d\n", node, var->hsync_len);
+ pr_debug("fb%d: var.vsync_len : %d\n", node, var->vsync_len);
+ pr_debug("fb%d: var.sync : 0x%X\n", node, var->sync);
+ pr_debug("fb%d: var.pixclock : %d\n\n", node, var->pixclock);
+}
+#endif /* 0 */
+
+
+/* ------------------------------------------------------------------------- */
+
+
+void svga_settile(struct fb_info *info, struct fb_tilemap *map)
+{
+ const u8 *font = map->data;
+ u8* fb = (u8 *) info->screen_base;
+ int i, c;
+
+ if ((map->width != 8) || (map->height != 16) ||
+ (map->depth != 1) || (map->length != 256)) {
+ printk(KERN_ERR "fb%d: unsupported font parameters: width %d, height %d, depth %d, length %d\n",
+ info->node, map->width, map->height, map->depth, map->length);
+ return;
+ }
+
+ fb += 2;
+ for (c = 0; c < map->length; c++) {
+ for (i = 0; i < map->height; i++) {
+ fb[i * 4] = font[i];
+ }
+ fb += 128;
+ font += map->height;
+ }
+}
+
+/* Copy area in text (tileblit) mode */
+void svga_tilecopy(struct fb_info *info, struct fb_tilearea *area)
+{
+ int dx, dy;
+ /* colstride is halved in this function because u16 are used */
+ int colstride = 1 << (info->fix.type_aux & FB_AUX_TEXT_SVGA_MASK);
+ int rowstride = colstride * (info->var.xres_virtual / 8);
+ u16 *fb = (u16 *) info->screen_base;
+ u16 *src, *dst;
+
+ if ((area->sy > area->dy) ||
+ ((area->sy == area->dy) && (area->sx > area->dx))) {
+ src = fb + area->sx * colstride + area->sy * rowstride;
+ dst = fb + area->dx * colstride + area->dy * rowstride;
+ } else {
+ src = fb + (area->sx + area->width - 1) * colstride
+ + (area->sy + area->height - 1) * rowstride;
+ dst = fb + (area->dx + area->width - 1) * colstride
+ + (area->dy + area->height - 1) * rowstride;
+
+ colstride = -colstride;
+ rowstride = -rowstride;
+ }
+
+ for (dy = 0; dy < area->height; dy++) {
+ u16* src2 = src;
+ u16* dst2 = dst;
+ for (dx = 0; dx < area->width; dx++) {
+ *dst2 = *src2;
+ src2 += colstride;
+ dst2 += colstride;
+ }
+ src += rowstride;
+ dst += rowstride;
+ }
+}
+
+/* Fill area in text (tileblit) mode */
+void svga_tilefill(struct fb_info *info, struct fb_tilerect *rect)
+{
+ int dx, dy;
+ int colstride = 2 << (info->fix.type_aux & FB_AUX_TEXT_SVGA_MASK);
+ int rowstride = colstride * (info->var.xres_virtual / 8);
+ int attr = (0x0F & rect->bg) << 4 | (0x0F & rect->fg);
+ u8 *fb = (u8 *) info->screen_base;
+ fb += rect->sx * colstride + rect->sy * rowstride;
+
+ for (dy = 0; dy < rect->height; dy++) {
+ u8* fb2 = fb;
+ for (dx = 0; dx < rect->width; dx++) {
+ fb2[0] = rect->index;
+ fb2[1] = attr;
+ fb2 += colstride;
+ }
+ fb += rowstride;
+ }
+}
+
+/* Write text in text (tileblit) mode */
+void svga_tileblit(struct fb_info *info, struct fb_tileblit *blit)
+{
+ int dx, dy, i;
+ int colstride = 2 << (info->fix.type_aux & FB_AUX_TEXT_SVGA_MASK);
+ int rowstride = colstride * (info->var.xres_virtual / 8);
+ int attr = (0x0F & blit->bg) << 4 | (0x0F & blit->fg);
+ u8* fb = (u8 *) info->screen_base;
+ fb += blit->sx * colstride + blit->sy * rowstride;
+
+ i=0;
+ for (dy=0; dy < blit->height; dy ++) {
+ u8* fb2 = fb;
+ for (dx = 0; dx < blit->width; dx ++) {
+ fb2[0] = blit->indices[i];
+ fb2[1] = attr;
+ fb2 += colstride;
+ i ++;
+ if (i == blit->length) return;
+ }
+ fb += rowstride;
+ }
+
+}
+
+/* Set cursor in text (tileblit) mode */
+void svga_tilecursor(struct fb_info *info, struct fb_tilecursor *cursor)
+{
+ u8 cs = 0x0d;
+ u8 ce = 0x0e;
+ u16 pos = cursor->sx + (info->var.xoffset / 8)
+ + (cursor->sy + (info->var.yoffset / 16))
+ * (info->var.xres_virtual / 8);
+
+ if (! cursor -> mode)
+ return;
+
+ svga_wcrt_mask(0x0A, 0x20, 0x20); /* disable cursor */
+
+ if (cursor -> shape == FB_TILE_CURSOR_NONE)
+ return;
+
+ switch (cursor -> shape) {
+ case FB_TILE_CURSOR_UNDERLINE:
+ cs = 0x0d;
+ break;
+ case FB_TILE_CURSOR_LOWER_THIRD:
+ cs = 0x09;
+ break;
+ case FB_TILE_CURSOR_LOWER_HALF:
+ cs = 0x07;
+ break;
+ case FB_TILE_CURSOR_TWO_THIRDS:
+ cs = 0x05;
+ break;
+ case FB_TILE_CURSOR_BLOCK:
+ cs = 0x01;
+ break;
+ }
+
+ /* set cursor position */
+ vga_wcrt(NULL, 0x0E, pos >> 8);
+ vga_wcrt(NULL, 0x0F, pos & 0xFF);
+
+ vga_wcrt(NULL, 0x0B, ce); /* set cursor end */
+ vga_wcrt(NULL, 0x0A, cs); /* set cursor start and enable it */
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+
+/*
+ * Compute PLL settings (M, N, R)
+ * F_VCO = (F_BASE * M) / N
+ * F_OUT = F_VCO / (2^R)
+ */
+
+static inline u32 abs_diff(u32 a, u32 b)
+{
+ return (a > b) ? (a - b) : (b - a);
+}
+
+int svga_compute_pll(const struct svga_pll *pll, u32 f_wanted, u16 *m, u16 *n, u16 *r, int node)
+{
+ u16 am, an, ar;
+ u32 f_vco, f_current, delta_current, delta_best;
+
+ pr_debug("fb%d: ideal frequency: %d kHz\n", node, (unsigned int) f_wanted);
+
+ ar = pll->r_max;
+ f_vco = f_wanted << ar;
+
+ /* overflow check */
+ if ((f_vco >> ar) != f_wanted)
+ return -EINVAL;
+
+ /* It is usually better to have greater VCO clock
+ because of better frequency stability.
+ So first try r_max, then r smaller. */
+ while ((ar > pll->r_min) && (f_vco > pll->f_vco_max)) {
+ ar--;
+ f_vco = f_vco >> 1;
+ }
+
+ /* VCO bounds check */
+ if ((f_vco < pll->f_vco_min) || (f_vco > pll->f_vco_max))
+ return -EINVAL;
+
+ delta_best = 0xFFFFFFFF;
+ *m = 0;
+ *n = 0;
+ *r = ar;
+
+ am = pll->m_min;
+ an = pll->n_min;
+
+ while ((am <= pll->m_max) && (an <= pll->n_max)) {
+ f_current = (pll->f_base * am) / an;
+ delta_current = abs_diff (f_current, f_vco);
+
+ if (delta_current < delta_best) {
+ delta_best = delta_current;
+ *m = am;
+ *n = an;
+ }
+
+ if (f_current <= f_vco) {
+ am ++;
+ } else {
+ an ++;
+ }
+ }
+
+ f_current = (pll->f_base * *m) / *n;
+ pr_debug("fb%d: found frequency: %d kHz (VCO %d kHz)\n", node, (int) (f_current >> ar), (int) f_current);
+ pr_debug("fb%d: m = %d n = %d r = %d\n", node, (unsigned int) *m, (unsigned int) *n, (unsigned int) *r);
+ return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+
+/* Check CRT timing values */
+int svga_check_timings(const struct svga_timing_regs *tm, struct fb_var_screeninfo *var, int node)
+{
+ u32 value;
+
+ var->xres = (var->xres+7)&~7;
+ var->left_margin = (var->left_margin+7)&~7;
+ var->right_margin = (var->right_margin+7)&~7;
+ var->hsync_len = (var->hsync_len+7)&~7;
+
+ /* Check horizontal total */
+ value = var->xres + var->left_margin + var->right_margin + var->hsync_len;
+ if (((value / 8) - 5) >= svga_regset_size (tm->h_total_regs))
+ return -EINVAL;
+
+ /* Check horizontal display and blank start */
+ value = var->xres;
+ if (((value / 8) - 1) >= svga_regset_size (tm->h_display_regs))
+ return -EINVAL;
+ if (((value / 8) - 1) >= svga_regset_size (tm->h_blank_start_regs))
+ return -EINVAL;
+
+ /* Check horizontal sync start */
+ value = var->xres + var->right_margin;
+ if (((value / 8) - 1) >= svga_regset_size (tm->h_sync_start_regs))
+ return -EINVAL;
+
+ /* Check horizontal blank end (or length) */
+ value = var->left_margin + var->right_margin + var->hsync_len;
+ if ((value == 0) || ((value / 8) >= svga_regset_size (tm->h_blank_end_regs)))
+ return -EINVAL;
+
+ /* Check horizontal sync end (or length) */
+ value = var->hsync_len;
+ if ((value == 0) || ((value / 8) >= svga_regset_size (tm->h_sync_end_regs)))
+ return -EINVAL;
+
+ /* Check vertical total */
+ value = var->yres + var->upper_margin + var->lower_margin + var->vsync_len;
+ if ((value - 1) >= svga_regset_size(tm->v_total_regs))
+ return -EINVAL;
+
+ /* Check vertical display and blank start */
+ value = var->yres;
+ if ((value - 1) >= svga_regset_size(tm->v_display_regs))
+ return -EINVAL;
+ if ((value - 1) >= svga_regset_size(tm->v_blank_start_regs))
+ return -EINVAL;
+
+ /* Check vertical sync start */
+ value = var->yres + var->lower_margin;
+ if ((value - 1) >= svga_regset_size(tm->v_sync_start_regs))
+ return -EINVAL;
+
+ /* Check vertical blank end (or length) */
+ value = var->upper_margin + var->lower_margin + var->vsync_len;
+ if ((value == 0) || (value >= svga_regset_size (tm->v_blank_end_regs)))
+ return -EINVAL;
+
+ /* Check vertical sync end (or length) */
+ value = var->vsync_len;
+ if ((value == 0) || (value >= svga_regset_size (tm->v_sync_end_regs)))
+ return -EINVAL;
+
+ return 0;
+}
+
+/* Set CRT timing registers */
+void svga_set_timings(const struct svga_timing_regs *tm, struct fb_var_screeninfo *var,
+ u32 hmul, u32 hdiv, u32 vmul, u32 vdiv, u32 hborder, int node)
+{
+ u8 regval;
+ u32 value;
+
+ value = var->xres + var->left_margin + var->right_margin + var->hsync_len;
+ value = (value * hmul) / hdiv;
+ pr_debug("fb%d: horizontal total : %d\n", node, value);
+ svga_wcrt_multi(tm->h_total_regs, (value / 8) - 5);
+
+ value = var->xres;
+ value = (value * hmul) / hdiv;
+ pr_debug("fb%d: horizontal display : %d\n", node, value);
+ svga_wcrt_multi(tm->h_display_regs, (value / 8) - 1);
+
+ value = var->xres;
+ value = (value * hmul) / hdiv;
+ pr_debug("fb%d: horizontal blank start: %d\n", node, value);
+ svga_wcrt_multi(tm->h_blank_start_regs, (value / 8) - 1 + hborder);
+
+ value = var->xres + var->left_margin + var->right_margin + var->hsync_len;
+ value = (value * hmul) / hdiv;
+ pr_debug("fb%d: horizontal blank end : %d\n", node, value);
+ svga_wcrt_multi(tm->h_blank_end_regs, (value / 8) - 1 - hborder);
+
+ value = var->xres + var->right_margin;
+ value = (value * hmul) / hdiv;
+ pr_debug("fb%d: horizontal sync start : %d\n", node, value);
+ svga_wcrt_multi(tm->h_sync_start_regs, (value / 8));
+
+ value = var->xres + var->right_margin + var->hsync_len;
+ value = (value * hmul) / hdiv;
+ pr_debug("fb%d: horizontal sync end : %d\n", node, value);
+ svga_wcrt_multi(tm->h_sync_end_regs, (value / 8));
+
+ value = var->yres + var->upper_margin + var->lower_margin + var->vsync_len;
+ value = (value * vmul) / vdiv;
+ pr_debug("fb%d: vertical total : %d\n", node, value);
+ svga_wcrt_multi(tm->v_total_regs, value - 2);
+
+ value = var->yres;
+ value = (value * vmul) / vdiv;
+ pr_debug("fb%d: vertical display : %d\n", node, value);
+ svga_wcrt_multi(tm->v_display_regs, value - 1);
+
+ value = var->yres;
+ value = (value * vmul) / vdiv;
+ pr_debug("fb%d: vertical blank start : %d\n", node, value);
+ svga_wcrt_multi(tm->v_blank_start_regs, value);
+
+ value = var->yres + var->upper_margin + var->lower_margin + var->vsync_len;
+ value = (value * vmul) / vdiv;
+ pr_debug("fb%d: vertical blank end : %d\n", node, value);
+ svga_wcrt_multi(tm->v_blank_end_regs, value - 2);
+
+ value = var->yres + var->lower_margin;
+ value = (value * vmul) / vdiv;
+ pr_debug("fb%d: vertical sync start : %d\n", node, value);
+ svga_wcrt_multi(tm->v_sync_start_regs, value);
+
+ value = var->yres + var->lower_margin + var->vsync_len;
+ value = (value * vmul) / vdiv;
+ pr_debug("fb%d: vertical sync end : %d\n", node, value);
+ svga_wcrt_multi(tm->v_sync_end_regs, value);
+
+ /* Set horizontal and vertical sync pulse polarity in misc register */
+
+ regval = vga_r(NULL, VGA_MIS_R);
+ if (var->sync & FB_SYNC_HOR_HIGH_ACT) {
+ pr_debug("fb%d: positive horizontal sync\n", node);
+ regval = regval & ~0x80;
+ } else {
+ pr_debug("fb%d: negative horizontal sync\n", node);
+ regval = regval | 0x80;
+ }
+ if (var->sync & FB_SYNC_VERT_HIGH_ACT) {
+ pr_debug("fb%d: positive vertical sync\n", node);
+ regval = regval & ~0x40;
+ } else {
+ pr_debug("fb%d: negative vertical sync\n\n", node);
+ regval = regval | 0x40;
+ }
+ vga_w(NULL, VGA_MIS_W, regval);
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+
+int svga_match_format(const struct svga_fb_format *frm, struct fb_var_screeninfo *var, struct fb_fix_screeninfo *fix)
+{
+ int i = 0;
+
+ while (frm->bits_per_pixel != SVGA_FORMAT_END_VAL)
+ {
+ if ((var->bits_per_pixel == frm->bits_per_pixel) &&
+ (var->red.length <= frm->red.length) &&
+ (var->green.length <= frm->green.length) &&
+ (var->blue.length <= frm->blue.length) &&
+ (var->transp.length <= frm->transp.length) &&
+ (var->nonstd == frm->nonstd)) {
+ var->bits_per_pixel = frm->bits_per_pixel;
+ var->red = frm->red;
+ var->green = frm->green;
+ var->blue = frm->blue;
+ var->transp = frm->transp;
+ var->nonstd = frm->nonstd;
+ if (fix != NULL) {
+ fix->type = frm->type;
+ fix->type_aux = frm->type_aux;
+ fix->visual = frm->visual;
+ fix->xpanstep = frm->xpanstep;
+ }
+ return i;
+ }
+ i++;
+ frm++;
+ }
+ return -EINVAL;
+}
+
+
+EXPORT_SYMBOL(svga_wcrt_multi);
+EXPORT_SYMBOL(svga_wseq_multi);
+
+EXPORT_SYMBOL(svga_set_default_gfx_regs);
+EXPORT_SYMBOL(svga_set_default_atc_regs);
+EXPORT_SYMBOL(svga_set_default_seq_regs);
+EXPORT_SYMBOL(svga_set_default_crt_regs);
+EXPORT_SYMBOL(svga_set_textmode_vga_regs);
+
+EXPORT_SYMBOL(svga_settile);
+EXPORT_SYMBOL(svga_tilecopy);
+EXPORT_SYMBOL(svga_tilefill);
+EXPORT_SYMBOL(svga_tileblit);
+EXPORT_SYMBOL(svga_tilecursor);
+
+EXPORT_SYMBOL(svga_compute_pll);
+EXPORT_SYMBOL(svga_check_timings);
+EXPORT_SYMBOL(svga_set_timings);
+EXPORT_SYMBOL(svga_match_format);
+
+MODULE_AUTHOR("Ondrej Zajicek <santiago@...reenet.org>");
+MODULE_DESCRIPTION("Common utility functions for VGA-based graphics cards");
+MODULE_LICENSE("GPL");
diff -uprN -X linux-2.6.20-x/Documentation/dontdiff linux-2.6.20-x/include/linux/fb.h linux-2.6.20-s3fb/include/linux/fb.h
--- linux-2.6.20-x/include/linux/fb.h 2007-02-04 19:44:54.000000000 +0100
+++ linux-2.6.20-s3fb/include/linux/fb.h 2007-02-05 14:26:14.000000000 +0100
@@ -49,6 +49,13 @@
#define FB_AUX_TEXT_S3_MMIO 2 /* S3 MMIO fasttext */
#define FB_AUX_TEXT_MGA_STEP16 3 /* MGA Millenium I: text, attr, 14 reserved bytes */
#define FB_AUX_TEXT_MGA_STEP8 4 /* other MGAs: text, attr, 6 reserved bytes */
+#define FB_AUX_TEXT_SVGA_GROUP 8 /* 8-15: SVGA tileblit compatible modes */
+#define FB_AUX_TEXT_SVGA_MASK 7 /* lower three bits says step */
+#define FB_AUX_TEXT_SVGA_STEP2 8 /* SVGA text mode: text, attr */
+#define FB_AUX_TEXT_SVGA_STEP4 9 /* SVGA text mode: text, attr, 2 reserved bytes */
+#define FB_AUX_TEXT_SVGA_STEP8 10 /* SVGA text mode: text, attr, 6 reserved bytes */
+#define FB_AUX_TEXT_SVGA_STEP16 11 /* SVGA text mode: text, attr, 14 reserved bytes */
+#define FB_AUX_TEXT_SVGA_LAST 15 /* reserved up to 15 */
#define FB_AUX_VGA_PLANES_VGA4 0 /* 16 color planes (EGA/VGA) */
#define FB_AUX_VGA_PLANES_CFB4 1 /* CFB4 in planes (VGA) */
diff -uprN -X linux-2.6.20-x/Documentation/dontdiff linux-2.6.20-x/include/linux/svga.h linux-2.6.20-s3fb/include/linux/svga.h
--- linux-2.6.20-x/include/linux/svga.h 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.20-s3fb/include/linux/svga.h 2007-02-06 19:05:49.000000000 +0100
@@ -0,0 +1,124 @@
+#ifndef _LINUX_SVGA_H
+#define _LINUX_SVGA_H
+
+#ifdef __KERNEL__
+
+#include <linux/pci.h>
+#include <video/vga.h>
+
+/* Terminator for register set */
+
+#define VGA_REGSET_END_VAL 0xFF
+#define VGA_REGSET_END {VGA_REGSET_END_VAL, 0, 0}
+
+struct vga_regset {
+ u8 regnum;
+ u8 lowbit;
+ u8 highbit;
+};
+
+/* ------------------------------------------------------------------------- */
+
+#define SVGA_FORMAT_END_VAL 0xFFFF
+#define SVGA_FORMAT_END {SVGA_FORMAT_END_VAL, {0, 0, 0}, {0, 0, 0}, {0, 0, 0}, {0, 0, 0}, 0, 0, 0, 0, 0, 0}
+
+struct svga_fb_format {
+ /* var part */
+ u32 bits_per_pixel;
+ struct fb_bitfield red;
+ struct fb_bitfield green;
+ struct fb_bitfield blue;
+ struct fb_bitfield transp;
+ u32 nonstd;
+ /* fix part */
+ u32 type;
+ u32 type_aux;
+ u32 visual;
+ u32 xpanstep;
+ u32 xresstep;
+};
+
+struct svga_timing_regs {
+ const struct vga_regset *h_total_regs;
+ const struct vga_regset *h_display_regs;
+ const struct vga_regset *h_blank_start_regs;
+ const struct vga_regset *h_blank_end_regs;
+ const struct vga_regset *h_sync_start_regs;
+ const struct vga_regset *h_sync_end_regs;
+
+ const struct vga_regset *v_total_regs;
+ const struct vga_regset *v_display_regs;
+ const struct vga_regset *v_blank_start_regs;
+ const struct vga_regset *v_blank_end_regs;
+ const struct vga_regset *v_sync_start_regs;
+ const struct vga_regset *v_sync_end_regs;
+};
+
+struct svga_pll {
+ u16 m_min;
+ u16 m_max;
+ u16 n_min;
+ u16 n_max;
+ u16 r_min;
+ u16 r_max; /* r_max < 32 */
+ u32 f_vco_min;
+ u32 f_vco_max;
+ u32 f_base;
+};
+
+
+/* Write a value to the attribute register */
+
+static inline void svga_wattr(u8 index, u8 data)
+{
+ inb(0x3DA);
+ outb(index, 0x3C0);
+ outb(data, 0x3C0);
+}
+
+/* Write a value to a sequence register with a mask */
+
+static inline void svga_wseq_mask(u8 index, u8 data, u8 mask)
+{
+ vga_wseq(NULL, index, (data & mask) | (vga_rseq(NULL, index) & ~mask));
+}
+
+/* Write a value to a CRT register with a mask */
+
+static inline void svga_wcrt_mask(u8 index, u8 data, u8 mask)
+{
+ vga_wcrt(NULL, index, (data & mask) | (vga_rcrt(NULL, index) & ~mask));
+}
+
+static inline int svga_primary_device(struct pci_dev *dev)
+{
+ u16 flags;
+ pci_read_config_word(dev, PCI_COMMAND, &flags);
+ return (flags & PCI_COMMAND_IO);
+}
+
+
+void svga_wcrt_multi(const struct vga_regset *regset, u32 value);
+void svga_wseq_multi(const struct vga_regset *regset, u32 value);
+
+void svga_set_default_gfx_regs(void);
+void svga_set_default_atc_regs(void);
+void svga_set_default_seq_regs(void);
+void svga_set_default_crt_regs(void);
+void svga_set_textmode_vga_regs(void);
+
+void svga_settile(struct fb_info *info, struct fb_tilemap *map);
+void svga_tilecopy(struct fb_info *info, struct fb_tilearea *area);
+void svga_tilefill(struct fb_info *info, struct fb_tilerect *rect);
+void svga_tileblit(struct fb_info *info, struct fb_tileblit *blit);
+void svga_tilecursor(struct fb_info *info, struct fb_tilecursor *cursor);
+
+int svga_compute_pll(const struct svga_pll *pll, u32 f_wanted, u16 *m, u16 *n, u16 *r, int node);
+int svga_check_timings(const struct svga_timing_regs *tm, struct fb_var_screeninfo *var, int node);
+void svga_set_timings(const struct svga_timing_regs *tm, struct fb_var_screeninfo *var, u32 hmul, u32 hdiv, u32 vmul, u32 vdiv, u32 hborder, int node);
+
+int svga_match_format(const struct svga_fb_format *frm, struct fb_var_screeninfo *var, struct fb_fix_screeninfo *fix);
+
+#endif /* __KERNEL__ */
+#endif /* _LINUX_SVGA_H */
+
--
Ondrej 'SanTiago' Zajicek (email: santiago@...l.cz, jabber: santiago@....netlab.cz)
OpenPGP encrypted e-mails preferred (KeyID 0x11DEADC3, wwwkeys.pgp.net)
"To err is human -- to blame it on a computer is even more so."
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists