| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20070227101100.GA22572@skl-net.de>
Date: Tue, 27 Feb 2007 11:11:00 +0100
From: Andre Noll <maan@...temlinux.org>
To: Andrew Vasquez <andrew.vasquez@...gic.com>
Cc: linux-kernel@...r.kernel.org, linux-scsi@...r.kernel.org,
James Bottomley <James.Bottomley@...elEye.com>
Subject: Re: qla2xxx BUG: workqueue leaked lock or atomic
On 10:26, Andrew Vasquez wrote:
> You are loading some stale firmware that's left over on the card --
> I'm not even sure what 4.00.70 is, as the latest release firmware is
> 4.00.27.
That's the firmware which came with the card. Anyway, I just upgraded
the firmware, but the bug remains. The backtrace differs a bit though
as now the tg3 network driver seems to be involved as well.
Thanks for your help
Andre
[ 67.511167] qla2xxx 0000:05:08.0: Allocated (64 KB) for EFT...
[ 67.511434] qla2xxx 0000:05:08.0: Allocated (1413 KB) for firmware dump...
[ 67.531231] scsi0 : qla2xxx
[ 67.854344] qla2xxx 0000:05:08.0:
[ 67.854346] QLogic Fibre Channel HBA Driver: 8.01.07-k4
[ 67.854347] QLogic HP AE369-60001 - QLA2340
[ 67.854348] ISP2422: PCI-X Mode 1 (133 MHz) @ 0000:05:08.0 hdma+, host#=0, fw=4.00.27 [IP]
[ 67.854881] ACPI: PCI Interrupt 0000:05:08.1[B] -> GSI 33 (level, low) -> IRQ 33
[ 67.855230] qla2xxx 0000:05:08.1: Found an ISP2422, irq 33, iobase 0xffffc20000012000
[ 67.855645] qla2xxx 0000:05:08.1: Configuring PCI space...
[ 67.855907] qla2xxx 0000:05:08.1: Configure NVRAM parameters...
[ 67.862486] qla2xxx 0000:05:08.1: Verifying loaded RISC code...
[ 68.106663] qla2xxx 0000:05:08.1: Allocated (64 KB) for EFT...
[ 68.107058] qla2xxx 0000:05:08.1: Allocated (1413 KB) for firmware dump...
[ 68.126759] scsi1 : qla2xxx
[ 68.196783] Adding 6540152k swap on /dev/md2. Priority:-1 extents:1 across:6540152k
[ 68.260645] qla2xxx 0000:05:08.0: LIP reset occured (f8f7).
[ 68.296027] qla2xxx 0000:05:08.0: LIP occured (f8f7).
[ 68.298214] qla2xxx 0000:05:08.0: LOOP UP detected (2 Gbps).
[ 68.326627] qla2xxx 0000:05:08.1:
[ 68.326628] QLogic Fibre Channel HBA Driver: 8.01.07-k4
[ 68.326630] QLogic HP AE369-60001 - QLA2340
[ 68.326631] ISP2422: PCI-X Mode 1 (133 MHz) @ 0000:05:08.1 hdma+, host#=1, fw=4.00.27 [IP]
[ 68.504335] EXT3 FS on md1, internal journal
[ 68.524627] PM: Writing back config space on device 0000:03:06.0 at offset b (was 164814e4, writing d00e11)
[ 68.524644] PM: Writing back config space on device 0000:03:06.0 at offset 3 (was 804000, writing 804010)
[ 68.524650] PM: Writing back config space on device 0000:03:06.0 at offset 2 (was 2000000, writing 2000010)
[ 68.524657] PM: Writing back config space on device 0000:03:06.0 at offset 1 (was 2b00000, writing 2b00146)
[ 68.532665] BUG: at kernel/lockdep.c:1860 trace_hardirqs_on()
[ 68.532784]
[ 68.532785] Call Trace:
[ 68.532979] <IRQ> [<ffffffff8024b877>] trace_hardirqs_on+0xd7/0x180
[ 68.533168] [<ffffffff80511f5b>] _spin_unlock_irq+0x2b/0x40
[ 68.533295] [<ffffffff88032747>] :qla2xxx:qla2x00_process_completed_request+0x137/0x1d0
[ 68.533457] [<ffffffff88032862>] :qla2xxx:qla2x00_status_entry+0x82/0xa40
[ 68.533577] [<ffffffff8024b17f>] __lock_acquire+0xcdf/0xd90
[ 68.533693] [<ffffffff80511ff2>] _spin_unlock_irqrestore+0x42/0x60
[ 68.533816] [<ffffffff880343fe>] :qla2xxx:qla24xx_intr_handler+0x4e/0x2b0
[ 68.533942] [<ffffffff88033551>] :qla2xxx:qla24xx_process_response_queue+0xc1/0x1c0
[ 68.534102] [<ffffffff88034584>] :qla2xxx:qla24xx_intr_handler+0x1d4/0x2b0
[ 68.534224] [<ffffffff8025e950>] handle_IRQ_event+0x20/0x60
[ 68.534339] [<ffffffff802604ad>] handle_fasteoi_irq+0xbd/0x110
[ 68.534459] [<ffffffff8020cf62>] do_IRQ+0x132/0x1a0
[ 68.534574] [<ffffffff8020a236>] ret_from_intr+0x0/0xf
[ 68.534687] <EOI> [<ffffffff803ad15c>] __delay+0xc/0x20
[ 68.534862] [<ffffffff803ad1a7>] __const_udelay+0x37/0x40
[ 68.534982] [<ffffffff88006737>] :tg3:tg3_chip_reset+0x547/0x670
[ 68.535103] [<ffffffff8800df2d>] :tg3:tg3_reset_hw+0x5d/0x1790
[ 68.535218] [<ffffffff803ad1e7>] __udelay+0x37/0x40
[ 68.535333] [<ffffffff8800408d>] :tg3:_tw32_flush+0x6d/0x80
[ 68.535451] [<ffffffff88012196>] :tg3:tg3_open+0x2d6/0x610
[ 68.535569] [<ffffffff8800f6a2>] :tg3:tg3_init_hw+0x42/0x50
[ 68.535687] [<ffffffff880121a3>] :tg3:tg3_open+0x2e3/0x610
[ 68.535804] [<ffffffff804b36e3>] dev_open+0x43/0x90
[ 68.535917] [<ffffffff804b2814>] dev_change_flags+0x74/0x160
[ 68.536034] [<ffffffff804f3e66>] devinet_ioctl+0x2e6/0x730
[ 68.536149] [<ffffffff804b4bc2>] dev_ioctl+0x302/0x340
[ 68.536264] [<ffffffff803aa71b>] __up_read+0x9b/0xb0
[ 68.536378] [<ffffffff804f42fc>] inet_ioctl+0x4c/0x70
[ 68.536494] [<ffffffff804a73ec>] sock_ioctl+0x1fc/0x230
[ 68.536610] [<ffffffff8029c701>] do_ioctl+0x31/0xa0
[ 68.536722] [<ffffffff8029ca2b>] vfs_ioctl+0x2bb/0x2e0
[ 68.536836] [<ffffffff8029ca9a>] sys_ioctl+0x4a/0x80
[ 68.536948] [<ffffffff80209cee>] system_call+0x7e/0x83
[ 68.537059]
[ 68.712832] scsi 0:0:0:0: Direct-Access transtec T6100F16R1-E 342I PQ: 0 ANSI: 5
[ 68.713384] sda : very big device. try to use READ CAPACITY(16).
[ 68.713594] SCSI device sda: 11714863104 512-byte hdwr sectors (5998010 MB)
[ 68.713976] sda: Write Protect is off
[ 68.714079] sda: Mode Sense: 9b 00 00 08
[ 68.714483] SCSI device sda: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 68.714876] sda : very big device. try to use READ CAPACITY(16).
[ 68.715080] SCSI device sda: 11714863104 512-byte hdwr sectors (5998010 MB)
[ 68.715436] sda: Write Protect is off
[ 68.715539] sda: Mode Sense: 9b 00 00 08
[ 68.715944] SCSI device sda: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 68.718244] sda: unknown partition table
[ 68.718707] sd 0:0:0:0: Attached scsi disk sda
[ 68.718945] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 68.719413] BUG: workqueue leaked lock or atomic: scsi_wq_0/0x00000000/2138
[ 68.719556] last function: fc_scsi_scan_rport+0x0/0x90
[ 68.719754] 1 lock held by scsi_wq_0/2138:
[ 68.719878] #0: (&shost->scan_mutex){--..}, at: [<ffffffff80510325>] mutex_lock+0x25/0x30
[ 68.720380]
[ 68.720381] Call Trace:
[ 68.720616] [<ffffffff80248319>] debug_show_held_locks+0x9/0x10
[ 68.720757] [<ffffffff8023eb49>] run_workqueue+0x149/0x1a0
[ 68.720891] [<ffffffff802427c0>] keventd_create_kthread+0x0/0x90
[ 68.721030] [<ffffffff8023edc1>] worker_thread+0x151/0x190
[ 68.721167] [<ffffffff80227e80>] default_wake_function+0x0/0x10
[ 68.721307] [<ffffffff8023ec70>] worker_thread+0x0/0x190
[ 68.721443] [<ffffffff80242a2a>] kthread+0xda/0x110
[ 68.721575] [<ffffffff8020ab08>] child_rip+0xa/0x12
[ 68.721709] [<ffffffff80511f5b>] _spin_unlock_irq+0x2b/0x40
[ 68.721842] [<ffffffff8020a28c>] restore_args+0x0/0x30
[ 68.721973] [<ffffffff80242950>] kthread+0x0/0x110
[ 68.722106] [<ffffffff8020aafe>] child_rip+0x0/0x12
[ 68.722240]
[ 68.762666] qla2xxx 0000:05:08.1: LIP reset occured (f7f7).
[ 68.797954] qla2xxx 0000:05:08.1: LIP occured (f7f7).
[ 68.800134] qla2xxx 0000:05:08.1: LOOP UP detected (2 Gbps).
[ 69.127937] scsi 1:0:0:0: Direct-Access ADVUNI OXYGENRAID 416F 341B PQ: 0 ANSI: 3
[ 69.128528] sdb : very big device. try to use READ CAPACITY(16).
[ 69.128777] SCSI device sdb: 9370656768 512-byte hdwr sectors (4797776 MB)
[ 69.129220] sdb: Write Protect is off
[ 69.129326] sdb: Mode Sense: 8f 00 00 08
[ 69.129878] SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 69.130342] sdb : very big device. try to use READ CAPACITY(16).
[ 69.130585] SCSI device sdb: 9370656768 512-byte hdwr sectors (4797776 MB)
[ 69.131006] sdb: Write Protect is off
[ 69.131110] sdb: Mode Sense: 8f 00 00 08
[ 69.131660] SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 69.131843] sdb: unknown partition table
[ 69.132401] sd 1:0:0:0: Attached scsi disk sdb
[ 69.132624] sd 1:0:0:0: Attached scsi generic sg1 type 0
Download attachment "signature.asc" of type "application/pgp-signature" (190 bytes)
Powered by blists - more mailing lists