| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <200703040149.46186.bzolnier@gmail.com>
Date: Sun, 4 Mar 2007 01:49:46 +0100
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
To: linux-ide@...r.kernel.org
Cc: linux-kernel@...r.kernel.org
Subject: [PATCH][pata-2.6 tree] pdc202xx_old: rewrite mode programming code
[PATCH] pdc202xx_old: rewrite mode programming code
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.
Rewrite mode programming code:
* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
even if both devices on the channel are not DMA capable and after reset
* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
as they need to be setup correctly also for PIO only devices, plus IORDY
wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
ATAPI devices
* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
(driver sets ->autotune to 1 so PIO modes are always programmed => lower
nibble of register A never equals 4 => "chipset_is_set" is always true)
* enable PIO mode programming for all ATAPI devices
(it was limited to ->media == ide_cdrom devices)
* remove extra reads of registers A/B/C, don't read register D et all
* do clearing / programming of registers A/B/C in one go
(gets rid of extra PCI config space read/write cycle)
* set initial values of drive_conf/AP/BP/CP variables to zero
(paranoia for the case when PCI reads fail)
* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
(ide_rate_filter() takes care of it)
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
* add FIXME comment about missing locking for 66MHz clock register
Also while at it:
* remove unused defines
* do a few cosmetic / CodingStyle fixes
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
---
drivers/ide/pci/pdc202xx_old.c | 176 +++++++++--------------------------------
1 file changed, 42 insertions(+), 134 deletions(-)
Index: b/drivers/ide/pci/pdc202xx_old.c
===================================================================
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -1,8 +1,9 @@
/*
- * linux/drivers/ide/pci/pdc202xx_old.c Version 0.36 Sept 11, 2002
+ * linux/drivers/ide/pci/pdc202xx_old.c Version 0.50 Mar 3, 2007
*
* Copyright (C) 1998-2002 Andre Hedrick <andre@...ux-ide.org>
* Copyright (C) 2006-2007 MontaVista Software, Inc.
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*
* Promise Ultra33 cards with BIOS v1.20 through 1.28 will need this
* compiled into the kernel if you have more than one card installed.
@@ -60,45 +61,7 @@ static const char *pdc_quirk_drives[] =
NULL
};
-/* A Register */
-#define SYNC_ERRDY_EN 0xC0
-
-#define SYNC_IN 0x80 /* control bit, different for master vs. slave drives */
-#define ERRDY_EN 0x40 /* control bit, different for master vs. slave drives */
-#define IORDY_EN 0x20 /* PIO: IOREADY */
-#define PREFETCH_EN 0x10 /* PIO: PREFETCH */
-
-#define PA3 0x08 /* PIO"A" timing */
-#define PA2 0x04 /* PIO"A" timing */
-#define PA1 0x02 /* PIO"A" timing */
-#define PA0 0x01 /* PIO"A" timing */
-
-/* B Register */
-
-#define MB2 0x80 /* DMA"B" timing */
-#define MB1 0x40 /* DMA"B" timing */
-#define MB0 0x20 /* DMA"B" timing */
-
-#define PB4 0x10 /* PIO_FORCE 1:0 */
-
-#define PB3 0x08 /* PIO"B" timing */ /* PIO flow Control mode */
-#define PB2 0x04 /* PIO"B" timing */ /* PIO 4 */
-#define PB1 0x02 /* PIO"B" timing */ /* PIO 3 half */
-#define PB0 0x01 /* PIO"B" timing */ /* PIO 3 other half */
-
-/* C Register */
-#define IORDYp_NO_SPEED 0x4F
-#define SPEED_DIS 0x0F
-
-#define DMARQp 0x80
-#define IORDYp 0x40
-#define DMAR_EN 0x20
-#define DMAW_EN 0x10
-
-#define MC3 0x08 /* DMA"C" timing */
-#define MC2 0x04 /* DMA"C" timing */
-#define MC1 0x02 /* DMA"C" timing */
-#define MC0 0x01 /* DMA"C" timing */
+static void pdc_old_disable_66MHz_clock(ide_hwif_t *);
static int pdc202xx_tune_chipset (ide_drive_t *drive, u8 xferspeed)
{
@@ -107,52 +70,23 @@ static int pdc202xx_tune_chipset (ide_dr
u8 drive_pci = 0x60 + (drive->dn << 2);
u8 speed = ide_rate_filter(drive, xferspeed);
- u32 drive_conf;
- u8 AP, BP, CP, DP;
+ u32 drive_conf = 0;
+ u8 AP = 0, BP = 0, CP = 0;
u8 TA = 0, TB = 0, TC = 0;
- if (drive->media != ide_disk &&
- drive->media != ide_cdrom && speed < XFER_SW_DMA_0)
- return -1;
+ /*
+ * TODO: do this once per channel
+ */
+ if (dev->device != PCI_DEVICE_ID_PROMISE_20246)
+ pdc_old_disable_66MHz_clock(hwif);
pci_read_config_dword(dev, drive_pci, &drive_conf);
- pci_read_config_byte(dev, (drive_pci), &AP);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
- pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
- pci_read_config_byte(dev, (drive_pci)|0x03, &DP);
- if (speed < XFER_SW_DMA_0) {
- if ((AP & 0x0F) || (BP & 0x07)) {
- /* clear PIO modes of lower 8421 bits of A Register */
- pci_write_config_byte(dev, (drive_pci), AP &~0x0F);
- pci_read_config_byte(dev, (drive_pci), &AP);
-
- /* clear PIO modes of lower 421 bits of B Register */
- pci_write_config_byte(dev, (drive_pci)|0x01, BP &~0x07);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-
- pci_read_config_byte(dev, (drive_pci), &AP);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
- }
- } else {
- if ((BP & 0xF0) && (CP & 0x0F)) {
- /* clear DMA modes of upper 842 bits of B Register */
- /* clear PIO forced mode upper 1 bit of B Register */
- pci_write_config_byte(dev, (drive_pci)|0x01, BP &~0xF0);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-
- /* clear DMA modes of lower 8421 bits of C Register */
- pci_write_config_byte(dev, (drive_pci)|0x02, CP &~0x0F);
- pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
- }
- }
-
- pci_read_config_byte(dev, (drive_pci), &AP);
- pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
- pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
+ pci_read_config_byte(dev, drive_pci, &AP);
+ pci_read_config_byte(dev, drive_pci + 1, &BP);
+ pci_read_config_byte(dev, drive_pci + 2, &CP);
switch(speed) {
- case XFER_UDMA_6: speed = XFER_UDMA_5;
case XFER_UDMA_5:
case XFER_UDMA_4: TB = 0x20; TC = 0x01; break;
case XFER_UDMA_2: TB = 0x20; TC = 0x01; break;
@@ -161,7 +95,7 @@ static int pdc202xx_tune_chipset (ide_dr
case XFER_UDMA_0:
case XFER_MW_DMA_2: TB = 0x60; TC = 0x03; break;
case XFER_MW_DMA_1: TB = 0x60; TC = 0x04; break;
- case XFER_MW_DMA_0:
+ case XFER_MW_DMA_0: TB = 0xE0; TC = 0x0F; break;
case XFER_SW_DMA_2: TB = 0x60; TC = 0x05; break;
case XFER_SW_DMA_1: TB = 0x80; TC = 0x06; break;
case XFER_SW_DMA_0: TB = 0xC0; TC = 0x0B; break;
@@ -174,25 +108,39 @@ static int pdc202xx_tune_chipset (ide_dr
}
if (speed < XFER_SW_DMA_0) {
- pci_write_config_byte(dev, (drive_pci), AP|TA);
- pci_write_config_byte(dev, (drive_pci)|0x01, BP|TB);
+ /*
+ * preserve SYNC_INT / ERDDY_EN bits while clearing
+ * Prefetch_EN / IORDY_EN / PA[3:0] bits of register A
+ */
+ AP &= ~0x3f;
+ if (drive->id->capability & 4)
+ AP |= 0x20; /* set IORDY_EN bit */
+ if (drive->media == ide_disk)
+ AP |= 0x10; /* set Prefetch_EN bit */
+ /* clear PB[4:0] bits of register B */
+ BP &= ~0x1f;
+ pci_write_config_byte(dev, drive_pci, AP | TA);
+ pci_write_config_byte(dev, drive_pci + 1, BP | TB);
} else {
- pci_write_config_byte(dev, (drive_pci)|0x01, BP|TB);
- pci_write_config_byte(dev, (drive_pci)|0x02, CP|TC);
+ /* clear MB[2:0] bits of register B */
+ BP &= ~0xe0;
+ /* clear MC[3:0] bits of register C */
+ CP &= ~0x0f;
+ pci_write_config_byte(dev, drive_pci + 1, BP | TB);
+ pci_write_config_byte(dev, drive_pci + 2, CP | TC);
}
#if PDC202XX_DEBUG_DRIVE_INFO
printk(KERN_DEBUG "%s: %s drive%d 0x%08x ",
drive->name, ide_xfer_verbose(speed),
drive->dn, drive_conf);
- pci_read_config_dword(dev, drive_pci, &drive_conf);
+ pci_read_config_dword(dev, drive_pci, &drive_conf);
printk("0x%08x\n", drive_conf);
-#endif /* PDC202XX_DEBUG_DRIVE_INFO */
+#endif
- return (ide_config_drive_speed(drive, speed));
+ return ide_config_drive_speed(drive, speed);
}
-
static void pdc202xx_tune_drive(ide_drive_t *drive, u8 pio)
{
pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
@@ -210,6 +158,8 @@ static u8 pdc202xx_old_cable_detect (ide
* Set the control register to use the 66MHz system
* clock for UDMA 3/4/5 mode operation when necessary.
*
+ * FIXME: this register is shared by both channels, some locking is needed
+ *
* It may also be possible to leave the 66MHz clock on
* and readjust the timing parameters.
*/
@@ -231,55 +181,13 @@ static void pdc_old_disable_66MHz_clock(
static int config_chipset_for_dma (ide_drive_t *drive)
{
- struct hd_driveid *id = drive->id;
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- u32 drive_conf = 0;
- u8 drive_pci = 0x60 + (drive->dn << 2);
- u8 test1 = 0, test2 = 0, speed = -1;
- u8 AP = 0;
-
- if (dev->device != PCI_DEVICE_ID_PROMISE_20246)
- pdc_old_disable_66MHz_clock(drive->hwif);
-
- drive_pci = 0x60 + (drive->dn << 2);
- pci_read_config_dword(dev, drive_pci, &drive_conf);
- if ((drive_conf != 0x004ff304) && (drive_conf != 0x004ff3c4))
- goto chipset_is_set;
+ u8 speed = ide_max_dma_mode(drive);
- pci_read_config_byte(dev, drive_pci, &test1);
- if (!(test1 & SYNC_ERRDY_EN)) {
- if (drive->select.b.unit & 0x01) {
- pci_read_config_byte(dev, drive_pci - 4, &test2);
- if ((test2 & SYNC_ERRDY_EN) &&
- !(test1 & SYNC_ERRDY_EN)) {
- pci_write_config_byte(dev, drive_pci,
- test1|SYNC_ERRDY_EN);
- }
- } else {
- pci_write_config_byte(dev, drive_pci,
- test1|SYNC_ERRDY_EN);
- }
- }
-
-chipset_is_set:
-
- pci_read_config_byte(dev, (drive_pci), &AP);
- if (id->capability & 4) /* IORDY_EN */
- pci_write_config_byte(dev, (drive_pci), AP|IORDY_EN);
- pci_read_config_byte(dev, (drive_pci), &AP);
- if (drive->media == ide_disk) /* PREFETCH_EN */
- pci_write_config_byte(dev, (drive_pci), AP|PREFETCH_EN);
-
- speed = ide_max_dma_mode(drive);
-
- if (!(speed)) {
- /* restore original pci-config space */
- pci_write_config_dword(dev, drive_pci, drive_conf);
+ if (!speed)
return 0;
- }
- (void) hwif->speedproc(drive, speed);
+ (void)pdc202xx_tune_chipset(drive, speed);
+
return ide_dma_enable(drive);
}
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists