Linux version 2.6.21-rc5 (lenb@d975xbx2) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #37 SMP Tue Mar 27 22:26:00 EDT 2007 Command line: root=/dev/sda2 debug BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001bfd0000 (usable) BIOS-e820: 000000001bfd0000 - 000000001bfe5600 (reserved) BIOS-e820: 000000001bfe5600 - 000000001bff8000 (ACPI NVS) BIOS-e820: 000000001bff8000 - 0000000020000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved) BIOS-e820: 00000000ffbc0000 - 00000000ffcc0000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 159) 0 entries of 3200 used Entering add_active_range(0, 256, 114640) 1 entries of 3200 used end_pfn_map = 1048576 DMI 2.4 present. ACPI: RSDP 000F7D30, 0024 (r2 HP ) ACPI: XSDT 1BFE57B4, 0054 (r1 HP 0944 6070620 HP 1) ACPI: FACP 1BFE5684, 00F4 (r4 HP 0944 3 HP 1) ACPI: DSDT 1BFE58DC, EE7A (r1 HP SB400 10000 MSFT 100000E) ACPI: FACS 1BFF7E80, 0040 ACPI: APIC 1BFE5808, 0062 (r1 HP 0944 1 HP 1) ACPI: MCFG 1BFE586C, 003C (r1 HP 0944 1 HP 1) ACPI: TCPA 1BFE58A8, 0032 (r2 HP 0944 1 HP 1) ACPI: SSDT 1BFF4756, 0059 (r1 HP HPQNLP 1 MSFT 100000E) ACPI: SSDT 1BFF47AF, 0182 (r1 HP PSSTBLID 1 HP 1) Scanning NUMA topology in Northbridge 24 Number of nodes 1 Node 0 MemBase 0000000000000000 Limit 000000001bfd0000 Entering add_active_range(0, 0, 159) 0 entries of 3200 used Entering add_active_range(0, 256, 114640) 1 entries of 3200 used NUMA: Using 63 for the hash shift. Using node hash shift of 63 Bootmem setup node 0 0000000000000000-000000001bfd0000 No mptable found. Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 early_node_map[2] active PFN ranges 0: 0 -> 159 0: 256 -> 114640 On node 0 totalpages: 114543 DMA zone: 56 pages used for memmap DMA zone: 1593 pages reserved DMA zone: 2350 pages, LIFO batch:0 DMA32 zone: 1511 pages used for memmap DMA32 zone: 109033 pages, LIFO batch:31 Normal zone: 0 pages used for memmap ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. Setting APIC routing to physical flat Using ACPI (MADT) for SMP configuration information Nosave address range: 000000000009f000 - 00000000000a0000 Nosave address range: 00000000000a0000 - 00000000000e0000 Nosave address range: 00000000000e0000 - 0000000000100000 Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 36992 bytes of per cpu data Built 1 zonelists. Total pages: 111383 Kernel command line: root=/dev/sda2 debug Initializing CPU#0 PID hash table entries: 2048 (order: 11, 16384 bytes) Extended CMOS year: 2000 time.c: Detected 1596.295 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Checking aperture... CPU 0: aperture @ 14b4000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 444360k/458560k available (3299k kernel code, 13812k reserved, 1848k data, 320k init) Calibrating delay using timer specific routine.. 3197.82 BogoMIPS (lpj=6395653) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU 0/0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20070126 Parsing all Control Methods: Table [DSDT](id 0001) - 1153 Objects with 113 Devices 337 Methods 33 Regions Parsing all Control Methods: Table [SSDT](id 0002) - 2 Objects with 0 Devices 2 Methods 0 Regions Parsing all Control Methods: Table [SSDT](id 0003) - 8 Objects with 0 Devices 0 Methods 0 Regions tbxface-0587 [02] tb_load_namespace : ACPI Tables successfully acquired evxfevnt-0091 [02] enable : Transition to ACPI mode successful ..MP-BIOS bug: 8254 timer not connected to IO-APIC Using local APIC timer interrupts. result 12471066 Detected 12.471 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 3192.24 BogoMIPS (lpj=6384480) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02 Brought up 2 CPUs migration_cost=141 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 - efffffff PCI: No mmconfig possible on device 00:18 evgpeblk-0952 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x15 evgpeblk-1049 [03] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 11 Runtime GPEs in this block Completing Region/Field/Buffer/Package initialization:.................................................................................................................................................................. Initialized 30/33 Regions 0/0 Fields 64/64 Buffers 68/78 Packages (1172 nodes) Initializing Device/Processor/Thermal objects by executing _INI methods:....... Executed 7 _INI methods requiring 2 _STA executions (examined 120 objects) ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [C074] (0000:00) PCI: Probing PCI hardware (bus 00) 0000:00:14.1: trying to change BAR0 from 0000 to 01F0 0000:00:14.1: trying to change BAR1 from 0000 to 03F4 0000:00:14.1: trying to change BAR2 from 0000 to 0170 0000:00:14.1: trying to change BAR3 from 0000 to 0374 Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.C074._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C074.C075._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C074.C0DF._PRT] ACPI: PCI Interrupt Link [C125] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C126] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C127] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C128] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C129] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C12A] (IRQs 9) *0, disabled. ACPI: PCI Interrupt Link [C12B] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C12C] (IRQs *10 11) ACPI: Power Resource [C223] (off) ACPI: Power Resource [C1FE] (off) ACPI: Power Resource [C217] (on) ACPI: Power Resource [C34B] (off) ACPI: Power Resource [C34C] (off) ACPI: Power Resource [C34D] (off) ACPI: Power Resource [C34E] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices SCSI subsystem initialized libata version 2.20 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 0 of device 0000:00:14.2 pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved Time: tsc clocksource has been installed. pnp: 00:00: iomem range 0x100000-0x1bffffff could not be reserved pnp: 00:0a: ioport range 0x40b-0x40b has been reserved pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0a: ioport range 0x4d6-0x4d6 has been reserved pnp: 00:0a: iomem range 0xffb00000-0xffbfffff has been reserved pnp: 00:0a: iomem range 0xfff00000-0xffffffff has been reserved pnp: 00:0b: ioport range 0x8000-0x802f has been reserved pnp: 00:0b: ioport range 0x8100-0x811f has been reserved pnp: 00:0b: iomem range 0xe0000000-0xefffffff has been reserved pnp: 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved pnp: 00:0c: iomem range 0xcf000-0xcffff has been reserved pnp: 00:0c: iomem range 0x1c000000-0x1fffffff could not be reserved pnp: 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved ACPI: PCI Interrupt 0000:02:04.1[A] -> GSI 20 (level, low) -> IRQ 20 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[d0011000-d00117ff] Max Packet=[2048] IR/IT contexts=[4/8] PCI: Bridge: 0000:00:01.0 IO window: 6000-6fff MEM window: d0300000-d03fffff PREFETCH window: c0000000-c3ffffff PCI: Bridge: 0000:00:04.0 IO window: 4000-5fff MEM window: cc000000-cfffffff PREFETCH window: disabled. PCI: Bridge: 0000:00:05.0 IO window: 2000-3fff MEM window: c8000000-cbffffff PREFETCH window: disabled. PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: c4000000-c40fffff PREFETCH window: disabled. PCI: Bus 3, cardbus bridge: 0000:02:04.0 Time: acpi_pm clocksource has been installed. IO window: 00001000-000010ff IO window: 00001400-000014ff PREFETCH window: 30000000-33ffffff MEM window: 38000000-3bffffff PCI: Bridge: 0000:00:14.4 IO window: 1000-1fff MEM window: d0000000-d02fffff PREFETCH window: 30000000-33ffffff PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:05.0 to 64 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 20 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 3, 32768 bytes) TCP established hash table entries: 16384 (order: 6, 393216 bytes) TCP bind hash table entries: 16384 (order: 6, 262144 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered Total HugeTLB memory allocated, 0 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:04.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] Allocate Port Service[0000:00:04.0:pcie01] Allocate Port Service[0000:00:04.0:pcie03] PCI: Setting latency timer of device 0000:00:05.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:05.0:pcie00] Allocate Port Service[0000:00:05.0:pcie01] Allocate Port Service[0000:00:05.0:pcie03] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie01] Allocate Port Service[0000:00:06.0:pcie03] Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 aer_init: AER service init fails - Run ACPI _OSC fails aer: probe of 0000:00:04.0:pcie01 failed with error 2 Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 aer_init: AER service init fails - Run ACPI _OSC fails aer: probe of 0000:00:05.0:pcie01 failed with error 2 Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 aer_init: AER service init fails - Run ACPI _OSC fails aer: probe of 0000:00:06.0:pcie01 failed with error 2 ACPI: AC Adapter [C1BD] (off-line) ACPI: Battery Slot [C1BF] (battery present) ACPI: Battery Slot [C1BE] (battery absent) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Sleep Button (CM) as /class/input/input1 ACPI: Sleep Button (CM) [C25A] input: Lid Switch as /class/input/input2 ACPI: Lid Switch [C25B] ACPI: Processor [C000] (supports 8 throttling states) ACPI: Processor [C001] (supports 8 throttling states) ACPI: Thermal Zone [TZ1] (66 C) ACPI: Thermal Zone [TZ2] (53 C) ACPI: Thermal Zone [TZ3] (26 C) Real Time Clock Driver v1.12ac Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled Floppy drive(s): fd0 is 1.44M floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 Copyright (c) 1999-2006 Intel Corporation. e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI e100: Copyright(c) 1999-2006 Intel Corporation tg3.c:v3.74 (February 20, 2007) ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 23 (level, low) -> IRQ 23 eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:17:08:30:e4:ee eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1] eth0: dma_rwctrl[763f0000] dma_mask[32-bit] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky netconsole: not configured, aborting Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 ATIIXP: chipset revision 128 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x7040-0x7047, BIOS settings: hda:DMA, hdb:pio ATIIXP: simplex device: DMA disabled ide1: ATIIXP Bus-Master DMA disabled (BIOS) Probing IDE interface ide0... hda: TSSTcorpCDW/DVD TS-L462C, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 24X DVD-ROM CD-R/RW drive, 1536kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) megasas: 00.00.03.10-rc1 Wed Feb 14 10:14:25 PST 2007 sata_sil 0000:00:12.0: version 2.1 ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16 ata1: SATA max UDMA/100 cmd 0xffffc20000036080 ctl 0xffffc2000003608a bmdma 0xffffc20000036000 irq 16 ata2: SATA max UDMA/100 cmd 0xffffc200000360c0 ctl 0xffffc200000360ca bmdma 0xffffc20000036008 irq 16 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: FUJITSU MHT2040BH, 0000104A, max UDMA/100 ata1.00: 78140160 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA FUJITSU MHT2040B 0000 PQ: 0 ANSI: 5 SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 Fusion MPT base driver 3.04.04 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.04 Fusion MPT SAS Host driver 3.04.04 ieee1394: raw1394: /dev/raw1394 device initialized ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19 ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 19, io mem 0xd0403000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 19, io mem 0xd0401000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0402000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected USB Universal Host Controller Interface driver v3.0 usb 3-1: new full speed USB device using ohci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:C214,PNP0f13:C215] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com Intel 810 + AC97 Audio, version 1.01, 22:52:57 Mar 25 2007 oprofile: using NMI interrupt. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 2 AMD Turion(tm) 64 X2 Mobile Technology TL-50 processors (version 2.00.00) powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13 powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e powernow-k8: ph2 null fid transition 0x8 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) synaptics reset failed synaptics reset failed synaptics reset failed Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000 serio: Synaptics pass-through port at isa0060/serio4/input0 input: SynPS/2 Synaptics TouchPad as /class/input/input4 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 320k freed rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 rtc_cmos: probe of 00:07 failed with error -16 Adding 674688k swap on /dev/sda1. Priority:-1 extents:1 across:674688k EXT3 FS on sda2, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode.