0x342 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2004.618 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1294252k/1309632k available (2072k kernel code, 14224k reserved, 714k data, 196k init, 392128k highmem) virtual kernel memory layout: fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc03bc000 - 0xc03ed000 ( 196 kB) .data : 0xc030618f - 0xc03b8b94 ( 714 kB) .text : 0xc0100000 - 0xc030618f (2072 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4011.25 BogoMIPS (lpj=2005626) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. CPU: AMD Mobile AMD Athlon 64 Processor 3000+ stepping 00 Checking 'hlt' instruction... OK. ACPI: Core revision 20070126 ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd64c, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 4000-407f claimed by vt8235 PM PCI quirk: region 8100-810f claimed by vt8235 SMB ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *5, disabled. ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *9, disabled. ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled. ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *5, disabled. ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 12 14 15) *9 ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.20 loaded. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:05: iomem range 0x0-0x9ffff could not be reserved pnp: 00:05: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:05: iomem range 0xfff00000-0xffffffff could not be reserved pnp: 00:05: iomem range 0xffee0000-0xffefffff has been reserved pnp: 00:06: ioport range 0x600-0x60f has been reserved pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:06: ioport range 0xfe10-0xfe11 has been reserved pnp: 00:06: ioport range 0xfe00-0xfe00 has been reserved Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:01.0 IO window: 2000-2fff MEM window: d0100000-d01fffff PREFETCH window: d8000000-dfffffff PCI: Bus 2, cardbus bridge: 0000:00:07.0 IO window: 00001c00-00001cff IO window: 00003000-000030ff PREFETCH window: 60000000-63ffffff MEM window: 64000000-67ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:07.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x37 set to 0x80 Machine check exception polling timer started. highmem bounce pool size: 64 pages io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Boot video device is 0000:01:00.0 vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 5742k, total 131072k vesafb: mode is 1400x1050x16, linelength=2800, pages=44 vesafb: protected mode interface info at c000:56ac vesafb: pmi: set display start = c00c571a, set palette = c00c5754 vesafb: pmi: ports = 2010 2016 2054 2038 203c 205c 2000 2004 20b0 20b2 20b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 175x65 fb0: VESA VGA frame buffer device Linux agpgart interface v0.102 (c) Dave Jones [drm] Initialized drm 1.1.0 20060810 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize tg3.c:v3.76 (May 5, 2007) ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 16 eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:c0:9f:67:01:5f eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1] eth0: dma_rwctrl[763f0000] dma_mask[32-bit] pata_via 0000:00:11.1: version 0.3.1 ACPI: Unable to derive IRQ for device 0000:00:11.1 ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI scsi0 : pata_via scsi1 : pata_via ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011860 irq 14 ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011868 irq 15 ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568 ata1.00: ATA-6: HTS721010G9AT00, MCZOA51A, max UDMA/100 ata1.00: 195371568 sectors, multi 16: LBA48 ata1.00: limited to UDMA/33 due to 40-wire cable ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568 ata1.00: configured for UDMA/33 Switched to high resolution mode on CPU 0 ata2.00: ATAPI, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA HTS721010G9AT00 MCZO PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-835S GQM5 PQ: 0 ANSI: 5 PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' Using IPI Shortcut mode input: AT Translated Set 2 keyboard as /class/input/input0 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 196k freed ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 18 (level, low) -> IRQ 17 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[d0015000-d00157ff] Max Packet=[2048] IR/IT contexts=[4/8] Real Time Clock Driver v1.12ac input: PC Speaker as /class/input/input1 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb irda_init() NET: Registered protocol family 23 USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 18 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:10.0: irq 18, io base 0x00001800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda caddy Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 18 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.1: irq 18, io base 0x00001820 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq ipw2200: Copyright(c) 2003-2006 Intel Corporation ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 18 usb 1-1: new full speed USB device using uhci_hcd and address 2 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.2: irq 18, io base 0x00001840 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f0000304fb1] usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-1: configuration #1 chosen from 1 choice sd 0:0:0:0: Attached scsi generic sg0 type 0 hub 1-1:1.0: USB hub found sr 1:0:0:0: Attached scsi generic sg1 type 5 hub 1-1:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 18 ehci_hcd 0000:00:10.3: EHCI Host Controller ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:10.3: irq 18, io mem 0xd0015800 ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected usb 1-1: USB disconnect, address 2 agpgart: Detected AGP bridge 0 agpgart: AGP aperture is 256M @ 0xe0000000 ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 19 ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006 input: SynPS/2 Synaptics TouchPad as /class/input/input2 parport_pc 00:0a: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1. nsc-ircc, chip->init nsc-ircc, Found chip at base=0x02e nsc-ircc, driver loaded (Dag Brattli) ipw2200: Detected geography ZZE (13 802.11bg channels, 19 802.11a channels) IrDA: Registered device irda0 nsc-ircc, Found dongle: HP HSDL-1100/HSDL-2100 ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:11.6 to 64 usb 4-1: new high speed USB device using ehci_hcd and address 2 usb 4-1: configuration #1 chosen from 1 choice hub 4-1:1.0: USB hub found hub 4-1:1.0: 4 ports detected Yenta: CardBus bridge found at 0000:00:07.0 [1025:0057] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:07.0, mfunc 0x007c1b22, devctl 0x44 Yenta: ISA IRQ mask 0x0a70, PCI irq 16 Socket status: 30000086 ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:11.5 to 64 usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice Initializing USB Mass Storage driver... scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568 ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568 ata1.00: configured for UDMA/33 ata1: EH complete sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Adding 1566328k swap on /dev/sda3. Priority:-1 extents:1 across:1566328k EXT3 FS on sda4, internal journal loop: module loaded fuse init (API version 7.8) ACPI: CPU0 (power states: C1[C1] C2[C2]) Marking TSC unstable due to: possible TSC halt in C2. Time: acpi_pm clocksource has been installed. powernow-k8: Found 1 Mobile AMD Athlon 64 Processor 3000+ processors (version 2.00.00) powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xc powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0xe powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x17 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. usb-storage: device scan complete scsi 2:0:0:0: Direct-Access Generic Flash R/W 2002 PQ: 0 ANSI: 2 sd 2:0:0:0: [sdb] Attached SCSI removable disk sd 2:0:0:0: Attached scsi generic sg2 type 0 ieee80211_crypt: registered algorithm 'TKIP' ACPI: Battery Slot [BAT1] (battery present) ACPI: AC Adapter [ACAD] (on-line) input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] input: Lid Switch as /class/input/input5 ACPI: Lid Switch [LID] input: Sleep Button (CM) as /class/input/input6 ACPI: Sleep Button (CM) [SLPB] ACPI: Thermal Zone [THRM] (52 C) lp0: using parport0 (interrupt-driven). ppdev: user-space parallel port driver PM: Writing back config space on device 0000:00:0b.0 at offset b (was 3ed173b, writing 571025) PM: Writing back config space on device 0000:00:0b.0 at offset 3 (was 0, writing 4010) PM: Writing back config space on device 0000:00:0b.0 at offset 2 (was 2000000, writing 2000003) PM: Writing back config space on device 0000:00:0b.0 at offset 1 (was 2b00000, writing 2b00006) PM: Writing back config space on device 0000:00:0b.0 at offset 0 (was 3ed173b, writing 169c14e4) Clocksource tsc unstable (delta = -72354138 ns) NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21 [drm] Initialized radeon 1.27.0 20060524 on minor 0 agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode [drm] Setting GART location based on new memory map [drm] Loading R300 Microcode [drm] writeback test succeeded in 1 usecs eth1: no IPv6 routers present