Linux version 2.6.22-rc2-ahci-slub (hari@fedora7) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #6 SMP Sun May 20 23:05:08 EST 2007 Command line: ro root=LABEL=/1234 console=ttyS0,115200 console=tty0 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable) BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS) BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data) BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000120000000 (usable) end_pfn_map = 1179648 DMI 2.4 present. ACPI: RSDP 000F8110, 0024 (r2 ATI ) ACPI: XSDT DFEE30C0, 0044 (r1 ATI ASUSACPI 42302E31 AWRD 0) ACPI: FACP DFEE83C0, 00F4 (r3 ATI ASUSACPI 42302E31 AWRD 0) ACPI: DSDT DFEE3240, 511E (r1 ATI ASUSACPI 1000 MSFT 3000000) ACPI: FACS DFEE0000, 0040 ACPI: SSDT DFEE85C0, 02CC (r1 PTLTD POWERNOW 1 LTP 1) ACPI: MCFG DFEE8980, 003C (r1 ATI ASUSACPI 42302E31 AWRD 0) ACPI: APIC DFEE8500, 0068 (r1 ATI ASUSACPI 42302E31 AWRD 0) Scanning NUMA topology in Northbridge 24 No NUMA configuration found Faking a node at 0000000000000000-0000000120000000 Bootmem setup node 0 0000000000000000-0000000120000000 Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1179648 early_node_map[3] active PFN ranges 0: 0 -> 159 0: 256 -> 917216 0: 1048576 -> 1179648 ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x4008 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at f1000000 (gap: f0000000:ec00000) PERCPU: Allocating 33672 bytes of per cpu data Built 1 zonelists. Total pages: 1030075 Kernel command line: ro root=LABEL=/1234 console=ttyS0,115200 console=tty0 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Marking TSC unstable due to TSCs unsynchronized time.c: Detected 2799.974 MHz processor. Console: colour VGA+ 80x25 Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 30 ... MAX_LOCKDEP_KEYS: 2048 ... CLASSHASH_SIZE: 1024 ... MAX_LOCKDEP_ENTRIES: 8192 ... MAX_LOCKDEP_CHAINS: 16384 ... CHAINHASH_SIZE: 8192 memory used by lock dependency info: 1648 kB per task-struct memory footprint: 1680 bytes Checking aperture... CPU 0: aperture @ 8000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Your BIOS doesn't leave a aperture memory hole Please enable the IOMMU option in the BIOS setup This costs you 64 MB of RAM Mapping aperture over 65536 KB of RAM @ 8000000 Memory: 4058408k/4718592k available (2102k kernel code, 134356k reserved, 1229k data, 308k init) SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, Processors=2, Nodes=1 Calibrating delay using timer specific routine.. 5604.66 BogoMIPS (lpj=11209328) Security Framework v1.0.0 initialized SELinux: Initializing. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0/0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Freeing SMP alternatives: 22k freed ACPI: Core revision 20070126 Using local APIC timer interrupts. result 12499895 Detected 12.499 MHz APIC timer. lockdep: not fixing up alternatives. Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 5600.19 BogoMIPS (lpj=11200386) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping 03 Brought up 2 CPUs migration_cost=50 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 - efffffff PCI: No mmconfig possible on device 00:18 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI-DMA: Disabling AGP. PCI-DMA: aperture base @ 8000000 size 65536 KB PCI-DMA: using GART IOMMU. PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture ACPI: RTC can wake from S4 pnp: 00:01: ioport range 0x4100-0x411f has been reserved pnp: 00:01: ioport range 0x228-0x22f has been reserved pnp: 00:01: ioport range 0x40b-0x40b has been reserved pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved pnp: 00:01: ioport range 0xc00-0xc01 has been reserved pnp: 00:01: ioport range 0xc14-0xc14 has been reserved pnp: 00:01: ioport range 0xc50-0xc52 has been reserved pnp: 00:01: ioport range 0xc6c-0xc6d has been reserved pnp: 00:09: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:0a: iomem range 0xf0000-0xf3fff could not be reserved pnp: 00:0a: iomem range 0xf4000-0xf7fff could not be reserved pnp: 00:0a: iomem range 0xf8000-0xfbfff could not be reserved pnp: 00:0a: iomem range 0xfc000-0xfffff could not be reserved PCI: Bridge: 0000:00:02.0 IO window: d000-dfff MEM window: fdc00000-fdcfffff PREFETCH window: f0000000-f7ffffff PCI: Bridge: 0000:00:07.0 IO window: e000-efff MEM window: fdb00000-fdbfffff PREFETCH window: fdf00000-fdffffff PCI: Bridge: 0000:00:14.4 IO window: c000-cfff Time: acpi_pm clocksource has been installed. MEM window: fde00000-fdefffff PREFETCH window: fdd00000-fddfffff NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 524288 (order: 13, 33554432 bytes) TCP bind hash table entries: 65536 (order: 9, 3670016 bytes) TCP: Hash tables configured (established 524288 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 3031k freed audit: initializing netlink socket (disabled) audit(1179666942.608:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) io scheduler noop registered io scheduler cfq registered (default) assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Fan [FAN] (on) ACPI: Thermal Zone [THRM] (40 C) Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize usbcore: registered new interface driver libusual PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ processors (version 2.00.00) powernow-k8: 0 : fid 0x14 (2800 MHz), vid 0x8 powernow-k8: 1 : fid 0x12 (2600 MHz), vid 0xa powernow-k8: 2 : fid 0x10 (2400 MHz), vid 0xc powernow-k8: 3 : fid 0xe (2200 MHz), vid 0xe powernow-k8: 4 : fid 0xc (2000 MHz), vid 0x10 powernow-k8: 5 : fid 0xa (1800 MHz), vid 0x10 powernow-k8: 6 : fid 0x2 (1000 MHz), vid 0x12 Freeing unused kernel memory: 308k freed BUG: spinlock bad magic on CPU#1, init/1 lock: ffff81011ec0a100, .magic: ffff8101, .owner: /-1, .owner_cpu: -1 Call Trace: [] _raw_spin_lock+0x22/0xf6 [] vma_adjust+0x219/0x454 [] vma_adjust+0x219/0x454 [] vma_merge+0x147/0x1f4 [] do_mmap_pgoff+0x414/0x7c7 [] _spin_unlock_irq+0x24/0x27 [] sys_mmap+0xe5/0x110 [] system_call+0x7e/0x83 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000 PM: Adding info for usb:usb1 PM: Adding info for No Bus:usbdev1.1_ep00 usb usb1: configuration #1 chosen from 1 choice PM: Adding info for usb:1-0:1.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev1.1_ep81 ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000 PM: Adding info for usb:usb2 PM: Adding info for No Bus:usbdev2.1_ep00 usb usb2: configuration #1 chosen from 1 choice PM: Adding info for usb:2-0:1.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev2.1_ep81 ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.2: OHCI Host Controller ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000 PM: Adding info for usb:usb3 PM: Adding info for No Bus:usbdev3.1_ep00 usb usb3: configuration #1 chosen from 1 choice PM: Adding info for usb:3-0:1.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev3.1_ep81 ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.3: OHCI Host Controller ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000 usb 2-1: new low speed USB device using ohci_hcd and address 2 PM: Adding info for usb:usb4 PM: Adding info for No Bus:usbdev4.1_ep00 usb usb4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-0:1.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev4.1_ep81 PM: Adding info for usb:2-1 PM: Adding info for No Bus:usbdev2.2_ep00 usb 2-1: configuration #1 chosen from 1 choice PM: Adding info for usb:2-1:1.0 ACPI: PCI Interrupt 0000:00:13.4[C] -> <6>input: Logitech USB Receiver as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.1-1 PM: Adding info for No Bus:usbdev2.2_ep81 PM: Adding info for usb:2-1:1.1 drivers/hid/usbhid/hid-core.c: Fixing up Logitech keyboard report descriptor GSI 18 (level, low) -> IRQ 18 input: Logitech USB Receiver as /class/input/input1 PM: Adding info for No Bus:hiddev0 input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1 PM: Adding info for No Bus:usbdev2.2_ep82 ohci_hcd 0000:00:13.4: OHCI Host Controller ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5 ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000 PM: Adding info for usb:usb5 PM: Adding info for No Bus:usbdev5.1_ep00 usb usb5: configuration #1 chosen from 1 choice PM: Adding info for usb:5-0:1.0 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev5.1_ep81 ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19 ehci_hcd 0000:00:13.5: EHCI Host Controller ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6 ehci_hcd 0000:00:13.5: debug port 1 ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000 ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb 2-1: USB disconnect, address 2 PM: Adding info for usb:usb6 PM: Adding info for No Bus:usbdev6.1_ep00 PM: Removing info for No Bus:usbdev2.2_ep81 PM: Removing info for usb:2-1:1.0 PM: Removing info for No Bus:usbdev2.2_ep82 PM: Removing info for No Bus:hiddev0 PM: Removing info for usb:2-1:1.1 PM: Removing info for No Bus:usbdev2.2_ep00 PM: Removing info for usb:2-1 usb usb6: configuration #1 chosen from 1 choice PM: Adding info for usb:6-0:1.0 hub 6-0:1.0: USB hub found hub 6-0:1.0: 10 ports detected PM: Adding info for No Bus:usbdev6.1_ep81 SCSI subsystem initialized libata version 2.20 loaded. ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 scsi0 : pata_atiixp PM: Adding info for No Bus:host0 scsi1 : pata_atiixp PM: Adding info for No Bus:host1 ata1: PATA max UDMA/100 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x000000000001f900 irq 14 ata2: PATA max UDMA/100 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x000000000001f908 irq 15 usb 2-1: new low speed USB device using ohci_hcd and address 3 ata1.00: ata_hpa_resize 1: sectors = 234435439, hpa_sectors = 234441648 ata1.00: Host Protected Area detected: current size: 234435439 sectors native size: 234441648 sectors ata1.00: ATA-6: ST3120026A, 3.06, max UDMA/100 ata1.00: 234435439 sectors, multi 1: LBA48 ata1.01: ATAPI, max UDMA/33 ata1.00: ata_hpa_resize 1: sectors = 234435439, hpa_sectors = 234441648 ata1.00: Host Protected Area detected: current size: 234435439 sectors native size: 234441648 sectors ata1.00: configured for UDMA/100 PM: Adding info for usb:2-1 PM: Adding info for No Bus:usbdev2.3_ep00 usb 2-1: configuration #1 chosen from 1 choice PM: Adding info for usb:2-1:1.0 input: Logitech USB Receiver as /class/input/input2 input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.1-1 PM: Adding info for No Bus:usbdev2.3_ep81 PM: Adding info for usb:2-1:1.1 drivers/hid/usbhid/hid-core.c: Fixing up Logitech keyboard report descriptor input: Logitech USB Receiver as /class/input/input3 PM: Adding info for No Bus:hiddev0 input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1 PM: Adding info for No Bus:usbdev2.3_ep82 ata1.01: configured for UDMA/33 ata2: device not ready (errno=-19), forcing hardreset ata2: BUG: prereset() requested invalid reset type PM: Adding info for No Bus:target0:0:0 scsi 0:0:0:0: Direct-Access ATA ST3120026A 3.06 PQ: 0 ANSI: 5 PM: Adding info for scsi:0:0:0:0 sd 0:0:0:0: [sda] 234435439 512-byte hardware sectors (120031 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 234435439 512-byte hardware sectors (120031 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 > sd 0:0:0:0: [sda] Attached SCSI disk PM: Adding info for No Bus:target0:0:1 scsi 0:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-4163B A102 PQ: 0 ANSI: 5 PM: Adding info for scsi:0:0:1:0 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. audit(1179666950.984:2): enforcing=1 old_enforcing=0 auid=4294967295 security: 3 users, 6 roles, 1817 types, 78 bools, 1 sens, 1024 cats security: 60 classes, 65667 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev sda1, type ext3), uses xattr SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts audit(1179666951.376:3): policy loaded auid=4294967295 PM: Removing info for No Bus:vcs1 PM: Removing info for No Bus:vcsa1 PM: Adding info for No Bus:vcs1 PM: Adding info for No Bus:vcsa1 PM: Removing info for No Bus:vcs1 PM: Removing info for No Bus:vcsa1 PM: Adding info for No Bus:vcs1 PM: Adding info for No Bus:vcsa1 PM: Removing info for No Bus:vcs1 PM: Removing info for No Bus:vcsa1 PM: Adding info for No Bus:vcs1 PM: Adding info for No Bus:vcsa1 PM: Removing info for No Bus:vcs1 PM: Removing info for No Bus:vcsa1 PM: Adding info for No Bus:vcs1 PM: Adding info for No Bus:vcsa1 PM: Removing info for No Bus:vcs1 PM: Removing info for No Bus:vcsa1 PM: Adding info for No Bus:vcs1 PM: Adding info for No Bus:vcsa1 BUG: spinlock lockup on CPU#0, sh/385, ffff81011ca8ffc0 Call Trace: [] _raw_spin_lock+0xcf/0xf6 [] anon_vma_unlink+0x1c/0x68 [] anon_vma_unlink+0x1c/0x68 [] free_pgtables+0x69/0xc3 [] exit_mmap+0x91/0xeb [] mmput+0x45/0xb8 [] flush_old_exec+0x65f/0x941 [] vfs_read+0x13f/0x153 [] load_elf_binary+0x0/0x197f [] load_elf_binary+0x460/0x197f [] __alloc_pages+0x72/0x2d4 [] load_elf_binary+0x0/0x197f [] search_binary_handler+0xc4/0x25f [] do_execve+0x188/0x231 [] sys_execve+0x36/0x8a [] stub_execve+0x67/0xb0