Linux version 2.6.22-rc2-plateado (root@plateado) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #3 SMP Mon May 21 19:38:38 EDT 2007 Command line: root=/dev/sdg3 ro mem=4096M BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000097c00 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable) BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS) BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data) BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000120000000 (usable) Entering add_active_range(0, 0, 151) 0 entries of 256 used Entering add_active_range(0, 256, 917216) 1 entries of 256 used end_pfn_map = 1048576 DMI 2.4 present. ACPI: RSDP 000F6E70, 0014 (r0 GBT ) ACPI: RSDT DFEE3040, 0034 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) ACPI: FACP DFEE30C0, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) ACPI: DSDT DFEE3180, 49F4 (r1 GBT GBTUACPI 1000 MSFT 100000C) ACPI: FACS DFEE0000, 0040 ACPI: HPET DFEE7CC0, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 98) ACPI: MCFG DFEE7D40, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101) ACPI: APIC DFEE7BC0, 0084 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Entering add_active_range(0, 0, 151) 0 entries of 256 used Entering add_active_range(0, 256, 917216) 1 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 early_node_map[2] active PFN ranges 0: 0 -> 151 0: 256 -> 917216 On node 0 totalpages: 917111 DMA zone: 56 pages used for memmap DMA zone: 960 pages reserved DMA zone: 2975 pages, LIFO batch:0 DMA32 zone: 12484 pages used for memmap DMA32 zone: 900636 pages, LIFO batch:31 Normal zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information swsusp: Registered nosave memory region: 0000000000097000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000 swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 Allocating PCI resources starting at e0000000 (gap: dff00000:10100000) SMP: Allowing 4 CPUs, 2 hotplug CPUs PERCPU: Allocating 37128 bytes of per cpu data Built 1 zonelists. Total pages: 903611 Kernel command line: root=/dev/sdg3 ro mem=4096M Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) time.c: Detected 2400.000 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... Memory: 3604856k/3668864k available (1953k kernel code, 63184k reserved, 974k data, 204k init) Calibrating delay using timer specific routine.. 4803.25 BogoMIPS (lpj=9606519) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K using mwait in idle threads. CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM2) SMP alternatives: switching to UP code ACPI: Core revision 20070126 Using local APIC timer interrupts. result 16666647 Detected 16.666 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4800.02 BogoMIPS (lpj=9600045) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM2) Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs migration_cost=19 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at f0000000 - f3ffffff mtrr: your CPUs had inconsistent variable MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: Interpreter enabled ACPI: (supports S0 S1 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 0480-04bf claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 *14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: ACPI device : hid PNP0A03 pnp: ACPI device : hid PNP0C02 pnp: ACPI device : hid PNP0200 pnp: ACPI device : hid PNP0B00 pnp: ACPI device : hid PNP0800 pnp: ACPI device : hid PNP0C04 pnp: ACPI device : hid PNP0700 pnp: ACPI device : hid PNP0501 pnp: ACPI device : hid PNP0400 pnp: ACPI device : hid PNP0C02 pnp: ACPI device : hid PNP0C02 pnp: ACPI device : hid PNP0C01 pnp: ACPI device : hid INT0800 pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.20 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NET: Registered protocol family 8 NET: Registered protocol family 20 BUG: at /usr/src/linux-2.6.22-rc2/mm/slab.c:777 __find_general_cachep() Call Trace: [] __kmalloc+0x3e/0xbe [] cache_k8_northbridges+0x7f/0xf0 [] gart_iommu_init+0x13/0x4f8 [] kobject_shadow_add+0xef/0x1a2 [] kobject_get+0x12/0x17 [] class_register+0x10a/0x13d [] pci_iommu_init+0x9/0x12 [] kernel_init+0x167/0x2d7 [] child_rip+0xa/0x12 [] acpi_ds_init_one_object+0x0/0x7c [] kernel_init+0x0/0x2d7 [] child_rip+0x0/0x12 PCI-GART: No AMD northbridge found. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz pnp: the driver 'system' has been registered pnp: match found with the PnP device '00:01' and the driver 'system' pnp: match found with the PnP device '00:09' and the driver 'system' pnp: 00:09: ioport range 0x400-0x4bf could not be reserved pnp: match found with the PnP device '00:0a' and the driver 'system' pnp: 00:0a: iomem range 0xf0000000-0xf3ffffff could not be reserved pnp: match found with the PnP device '00:0b' and the driver 'system' pnp: 00:0b: iomem range 0xf0000-0xf3fff could not be reserved pnp: 00:0b: iomem range 0xf4000-0xf7fff could not be reserved pnp: 00:0b: iomem range 0xf8000-0xfbfff could not be reserved pnp: 00:0b: iomem range 0xfc000-0xfffff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: 7000-7fff MEM window: f4000000-f6ffffff PREFETCH window: e0000000-efffffff PCI: Bridge: 0000:00:1c.0 IO window: 6000-6fff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: 8000-8fff MEM window: f7000000-f8ffffff PREFETCH window: f9300000-f93fffff PCI: Bridge: 0000:00:1c.5 IO window: 9000-afff MEM window: f9000000-f90fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: b000-bfff MEM window: f9100000-f91fffff PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16 Time: tsc clocksource has been installed. PCI: Setting latency timer of device 0000:00:1c.4 to 64 ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 131072 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 2610k freed io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] Allocate Port Service[0000:00:1c.4:pcie03] PCI: Setting latency timer of device 0000:00:1c.5 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.5:pcie00] Allocate Port Service[0000:00:1c.5:pcie02] Allocate Port Service[0000:00:1c.5:pcie03] Real Time Clock Driver v1.12ac Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled pnp: the driver 'serial' has been registered pnp: match found with the PnP device '00:07' and the driver 'serial' 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize ahci 0000:00:1f.2: version 2.1 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl RAID mode ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 cmd 0xffffc20000016100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata2: SATA max UDMA/133 cmd 0xffffc20000016180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata3: SATA max UDMA/133 cmd 0xffffc20000016200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata4: SATA max UDMA/133 cmd 0xffffc20000016280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata5: SATA max UDMA/133 cmd 0xffffc20000016300 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata6: SATA max UDMA/133 cmd 0xffffc20000016380 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168 ata1.00: ATA-7: ST3500630AS, 3.AAE, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168 ata1.00: configured for UDMA/133 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168 ata2.00: ATA-7: ST3500630AS, 3.AAE, max UDMA/133 ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168 ata2.00: configured for UDMA/133 ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata3.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata3.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133 ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata3.00: configured for UDMA/133 ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata4.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133 ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata4.00: configured for UDMA/133 ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata5.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata5.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133 ata5.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) ata5.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata5.00: configured for UDMA/133 ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata6.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata6.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133 ata6.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) ata6.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata6.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 scsi 1:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 scsi 5:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17 ahci 0000:04:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:04:00.0 to 64 scsi6 : ahci scsi7 : ahci ata7: SATA max UDMA/133 cmd 0xffffc20000018100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata8: SATA max UDMA/133 cmd 0xffffc20000018180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata7: SATA link down (SStatus 0 SControl 300) ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata8.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata8.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133 ata8.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) ata8.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448 ata8.00: configured for UDMA/133 scsi 7:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 ACPI: PCI Interrupt 0000:04:00.1[B] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:04:00.1 to 64 scsi8 : pata_jmicron scsi9 : pata_jmicron ata9: PATA max UDMA/100 cmd 0x0000000000019000 ctl 0x0000000000019402 bmdma 0x000000000001a000 irq 0 ata10: PATA max UDMA/100 cmd 0x0000000000019800 ctl 0x0000000000019c02 bmdma 0x000000000001a008 irq 0 ata9.00: ATAPI, max UDMA/33 ata9.00: configured for UDMA/33 ATA: abnormal status 0x7F on port 0x0000000000019807 scsi 8:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S182M SB03 PQ: 0 ANSI: 5 pnp: the driver 'i8042 kbd' has been registered pnp: the driver 'i8042 aux' has been registered pnp: the driver 'i8042 kbd' has been unregistered pnp: the driver 'i8042 aux' has been unregistered PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 204k freed ACPI: Processor [CPU0] (supports 2 throttling states) ACPI: Processor [CPU1] (supports 2 throttling states) ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda: p1 exceeds device capacity sd 0:0:0:0: [sda] Attached SCSI disk sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 1:0:0:0: [sdb] Attached SCSI disk sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sdc: p1 exceeds device capacity sd 2:0:0:0: [sdc] Attached SCSI disk sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB) sd 3:0:0:0: [sdd] Write Protect is off sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB) sd 3:0:0:0: [sdd] Write Protect is off sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: unknown partition table sd 3:0:0:0: [sdd] Attached SCSI disk sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB) sd 4:0:0:0: [sde] Write Protect is off sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB) sd 4:0:0:0: [sde] Write Protect is off sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: unknown partition table sd 4:0:0:0: [sde] Attached SCSI disk sd 5:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB) sd 5:0:0:0: [sdf] Write Protect is off sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 5:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB) sd 5:0:0:0: [sdf] Write Protect is off sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdf:<6>USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000d000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected sdf1 sdf: p1 exceeds device capacity sd 5:0:0:0: [sdf] Attached SCSI disk sd 7:0:0:0: [sdg] 625142448 512-byte hardware sectors (320073 MB) sd 7:0:0:0: [sdg] Write Protect is off sd 7:0:0:0: [sdg] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 7:0:0:0: [sdg] 625142448 512-byte hardware sectors (320073 MB) sd 7:0:0:0: [sdg] Write Protect is off sd 7:0:0:0: [sdg] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdg:sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 8:0:0:0: Attached scsi CD-ROM sr0 sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 2:0:0:0: Attached scsi generic sg2 type 0 sd 3:0:0:0: Attached scsi generic sg3 type 0 sd 4:0:0:0: Attached scsi generic sg4 type 0 sd 5:0:0:0: Attached scsi generic sg5 type 0 sd 7:0:0:0: Attached scsi generic sg6 type 0 sr 8:0:0:0: Attached scsi generic sg7 type 5 sdg1 sdg2 sdg3 sd 7:0:0:0: [sdg] Attached SCSI disk Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 attempt to access beyond end of device sda: rw=0, want=1953533832, limit=976773168 Buffer I/O error on device sda1, logical block 244191472 attempt to access beyond end of device sda: rw=0, want=1953533832, limit=976773168 Buffer I/O error on device sda1, logical block 244191472 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 Buffer I/O error on device sda1, logical block 244191487 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 Buffer I/O error on device sda1, logical block 244191487 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 Buffer I/O error on device sda1, logical block 244191487 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 Buffer I/O error on device sda1, logical block 244191487 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 Buffer I/O error on device sda1, logical block 244191487 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 Buffer I/O error on device sda1, logical block 244191487 attempt to access beyond end of device sda: rw=0, want=1953533896, limit=976773168 Buffer I/O error on device sda1, logical block 244191480 attempt to access beyond end of device sda: rw=0, want=1953533944, limit=976773168 Buffer I/O error on device sda1, logical block 244191486 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000c000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected attempt to access beyond end of device sdf: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410888, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410936, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410888, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410936, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 18 (level, low) -> IRQ 18 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9205000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[f9104000-f91047ff] Max Packet=[2048] IR/IT contexts=[4/8] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9204000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c400 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c800 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000cc00 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected usb 3-1: new high speed USB device using ehci_hcd and address 2 Attempting manual resume usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 4 ports detected kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ieee1394: Host added: ID:BUS[0-01:1023] GUID[0016e60000bb7d74] usb 7-1: new low speed USB device using uhci_hcd and address 2 usb 7-1: configuration #1 chosen from 1 choice attempt to access beyond end of device sdf: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410888, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410936, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdf: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410824, limit=625142448 attempt to access beyond end of device sda: rw=0, want=1953533832, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533832, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410888, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410936, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 attempt to access beyond end of device sdc: rw=0, want=1875410944, limit=625142448 sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533896, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533944, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 attempt to access beyond end of device sda: rw=0, want=1953533952, limit=976773168 usb 7-2: new full speed USB device using uhci_hcd and address 3 agpgart: Detected an Intel 965G Chipset. agpgart: AGP aperture is 256M @ 0x0 usb 7-2: configuration #1 chosen from 1 choice hub 7-2:1.0: USB hub found hub 7-2:1.0: 4 ports detected ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:03:00.0 to 64 sky2 0000:03:00.0: v1.14 addr 0xf8000000 irq 16 Yukon-EC (0xb6) rev 2 sky2 eth0: addr 00:16:e6:88:62:d5 input: PC Speaker as /class/input/input0 usb 3-1.1: new high speed USB device using ehci_hcd and address 4 ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18 usb 3-1.1: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev Initializing USB Mass Storage driver... ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1b.0 to 64 usb 1-2: new full speed USB device using uhci_hcd and address 2 usb 1-2: configuration #1 chosen from 1 choice ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 20 (level, low) -> IRQ 20 usb 7-2.1: new low speed USB device using uhci_hcd and address 4 hiddev96: USB HID v1.11 Device [Belkin Belkin UPS] on usb-0000:00:1d.2-1 usb 7-2.1: configuration #1 chosen from 1 choice scsi10 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input1 input: USB HID v1.11 Keyboard [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:1d.2-2.1 input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input2 input: USB HID v1.11 Device [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:1d.2-2.1 input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input3 input: USB HID v1.10 Mouse [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:1d.2-2.1 usbcore: registered new interface driver usbhid usbcore: registered new interface driver usb-storage USB Mass Storage support registered. /usr/src/linux-2.6.22-rc2/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Adding 262136k swap on /dev/sdg2. Priority:-1 extents:1 across:262136k EXT3 FS on sdg3, internal journal loop: module loaded device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com sky2 eth1: enabling interface sky2 eth1: ram buffer 48K