| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <F1D642E5A91BC94D9504EC83AE19E6B0128A22@ecqcmtlmail3.quebec.int.ec.gc.ca>
Date: Thu, 21 Jun 2007 13:26:59 -0400
From: "Fortier,Vincent [Montreal]" <Vincent.Fortier1@...GC.CA>
To: <linux-kernel@...r.kernel.org>
Subject: Broadcom (bnx2) on PE1950/2950 failure
When trying manually to get the on-board broadcom adapter working I get
this:
Jun 21 16:50:47 urpdev1 kernel: [ 184.528092] Broadcom NetXtreme II
Gigabit Ethernet Driver bnx2 v1.4.45 (September 29, 2006)
Jun 21 16:50:47 urpdev1 kernel: [ 184.539831] ACPI: PCI Interrupt
0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 17
Jun 21 16:50:48 urpdev1 kernel: [ 184.551805] eth0: Broadcom NetXtreme
II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000,
IRQ 17, node ad dr 0019b9c8eedc
Jun 21 16:50:48 urpdev1 kernel: [ 184.576672] ACPI: PCI Interrupt
0000:09:00.0[A] -> GSI 17 (level, low) -> IRQ 16
Jun 21 16:50:48 urpdev1 kernel: [ 184.590359] eth0: Broadcom NetXtreme
II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000,
IRQ 16, node ad dr 0019b9c8eede
Jun 21 16:50:52 urpdev1 dhclient: Internet Systems Consortium DHCP
Client V3.0.1
Jun 21 16:50:52 urpdev1 dhclient: Copyright 2004 Internet Systems
Consortium.
Jun 21 16:50:52 urpdev1 dhclient: All rights reserved.
Jun 21 16:50:52 urpdev1 dhclient: For info, please visit
http://www.isc.org/products/DHCP
Jun 21 16:50:52 urpdev1 dhclient:
Jun 21 16:50:53 urpdev1 dhclient: Bind socket to interface: No such
device
When I invoke "modprobe bnx2" it looks like both adapter fails to
initialise properly reason I think both are trying to bind on eth0
instead of eth0 & eth1.
I've removed the TOE jumper (has read on a gentoo list) with no effect
(except that it really is disabled in the BIOS now).
I've also tried loading the driver using disable_msi=1 option without
any effect.
The problem occurs on all tested kernels (2.6.18.8, 2.6.19.7, 2.6.20.14
& 2.6.21.5)
Here is part of the dmesg:
[root@...alhost /root]# dmesg | grep -i eth
[ 119.196375] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2
v1.5.8.1 (May 7, 2007)
[ 119.215023] eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X
64-bit 133MHz found at mem f8000000, IRQ 17, node addr 0019b9c8eedc
[ 119.246853] eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X
64-bit 133MHz found at mem f4000000, IRQ 16, node addr 0019b9c8eede
[ 119.458598] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network
Connection
[ 119.654095] e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network
Connection
[ 266.513144] bnx2: eth3: using MSI
[ 269.638237] bnx2: eth3 NIC Link is Up, 1000 Mbps full duplex, receive
& transmit flow control ON
[ 290.242533] eth3: no IPv6 routers present
As you can notice it tried to use eth0 & eth1 for both broadcom adapters
but it did not worked properly since e1000 used them instead and finally
bnx2 got eth3 working using MSI ?
Here is the mii-tool output:
[root@...dev1 /root]# mii-tool
eth0: no link
eth1: no link
SIOCGMIIPHY on 'eth2' failed: Resource temporarily unavailable
eth3: negotiated 100baseTx-FD flow-control, link ok
So by switching the network config from eth0 to eth3 made the on-board
port 1 working ?
Here is the lspci output:
05:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708
Gigabit Ethernet (rev 12)
Subsystem: Dell Unknown device 01b2
Control: I/O- Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 214
Region 0: Memory at f8000000 (64-bit, non-prefetchable)
[size=32M]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=8
Status: Dev=05:00.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable+
Address: 00000000feeff00c Data: 416a
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708
Gigabit Ethernet (rev 12)
Subsystem: Dell Unknown device 01b2
Control: I/O- Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4000000 (64-bit, non-prefetchable)
[size=32M]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=8
Status: Dev=09:00.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 6feffffffdfffefc Data: ffbf
Full dmesg:
http://linux-dev.qc.ec.gc.ca/kernel/debian/dmesg-2.6.21.5-bnx2-error.txt
Full lspci -vvv:
http://linux-dev.qc.ec.gc.ca/kernel/debian/lspci-2.6.21.5-bnx2-error.txt
Config (2.6.21.5):
http://linux-dev.qc.ec.gc.ca/kernel/debian/CONFIG-i686-2.6.21-005
Help would greatly be appreciated!
- vin
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists