linux-kernel - Re: Regression: 2.6.22-rcX: hda: lost interrupt

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <468516B9.1080300@garzik.org>
Date:	Fri, 29 Jun 2007 10:27:05 -0400
From:	Jeff Garzik <jeff@...zik.org>
To:	David Chinner <dgc@....com>
CC:	lkml <linux-kernel@...r.kernel.org>
Subject: Re: Regression: 2.6.22-rcX: hda: lost interrupt

David Chinner wrote:
> Folks,
> 
> After updating an x86_64 machine from 2.6.21 to 2.6.22-rc6 and
> fighting off the where-the-fuck-did-my-serial-console-go blues
> (legacy_serial.force), I finally discovered why the damn thing
> wasn't booting - the machine was sitting there in a loop outputting
> "hda: lost interrupt" over and over again during hardware
> discovery (hda = dvd drive).
> 
> It doesn't happen on every boot - more boots hung than failed,
> though, while I was trying to work out where my serial port
> went and get some work done.
> 
> Since I've had the console operative, the boot hangs are
> basically like:
> 
> ESB2: IDE controller at PCI slot 0000:00:1f.1
> ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 20 (level, low) -> IRQ20
> ESB2: chipset revision 9
> ESB2: not 100% native mode: will probe irqs later
>     ide0: DM-DMA at 0x50a0-0x50a7, BIOS settings: hda:DMA, hdb:pio
>     ide1: DM-DMA at 0x50a8-0x50af, BIOS settings: hda:pio, hdb:pio
> Probing IDE interface ide0...
> hda: probing with STATUS(0xa0) instead of ALTSTATUS(0x58)
> hda: <some ctrl char>, ATAPI UNKNOWN (type 31) drive
> hdb: probing with STATUS(0xb0) instead of ALTSTATUS(0x00)
> hdb: probing with STATUS(0xa1) instead of ALTSTATUS(0x51)
> hdb: <some ctrl char>, ATAPI UNKNOWN (type 31) drive
> hda: set_drive_speed_status: status=0x58 { DriveReady SeekComplete DataRequest }
> hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
> hda: set_drive_speed_status: error=0x04 { AbortedCommand }
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt
> hda: lost interrupt

What is the behavior under libata?

If you see timeouts/etc. there too, it might be an interrupt routing or 
hardware problem.

	Jeff



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/