Linux version 2.6.22 (root@blight) (gcc version 4.1.2 (Gentoo 4.1.2)) #5 SMP Tue Jul 10 21:33:11 CEST 2007
Command line: BOOT_IMAGE=GentooLinux ro root=805 quiet splash=verbose,theme:livecd-2006.1,tty:11 CONSOLE=/dev/tty1
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
 BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ff90000 (usable)
 BIOS-e820: 000000007ff90000 - 000000007ff9e000 (ACPI data)
 BIOS-e820: 000000007ff9e000 - 000000007ffe0000 (ACPI NVS)
 BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 524176) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000FAE40, 0024 (r2 ACPIAM)
ACPI: XSDT 7FF90100, 0054 (r1 ÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿ  3000709 MSFT       97)
ACPI: FACP 7FF90290, 00F4 (r3 MSTEST OEMFACP   3000709 MSFT       97)
ACPI: DSDT 7FF905C0, 8E7D (r1  A0483 A0483035       35 INTL 20060113)
ACPI: FACS 7FF9E000, 0040
ACPI: APIC 7FF90390, 006C (r1 MSTEST OEMAPIC   3000709 MSFT       97)
ACPI: MCFG 7FF90400, 003C (r1 MSTEST OEMMCFG   3000709 MSFT       97)
ACPI: SLIC 7FF90440, 0176 (r1 ÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿ  3000709 MSFT       97)
ACPI: OEMB 7FF9E040, 007B (r1 MSTEST AMI_OEM   3000709 MSFT       97)
ACPI: HPET 7FF99440, 0038 (r1 MSTEST OEMHPET   3000709 MSFT       97)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 524176) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
early_node_map[2] active PFN ranges
    0:        0 ->      158
    0:      256 ->   524176
On node 0 totalpages: 524078
  DMA zone: 56 pages used for memmap
  DMA zone: 1735 pages reserved
  DMA zone: 2207 pages, LIFO batch:0
  DMA32 zone: 7110 pages used for memmap
  DMA32 zone: 512970 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a202 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:7ee00000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 32648 bytes of per cpu data
Built 1 zonelists.  Total pages: 515177
Kernel command line: BOOT_IMAGE=GentooLinux ro root=805 quiet splash=verbose,theme:livecd-2006.1,tty:11 CONSOLE=/dev/tty1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
time.c: Detected 1866.667 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
Memory: 2057300k/2096704k available (3046k kernel code, 38864k reserved, 1373k data, 252k init)
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 3735.47 BogoMIPS (lpj=1867737)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 16666676
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3733.31 BogoMIPS (lpj=1866658)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU          6300  @ 1.86GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=16
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI-GART: No AMD northbridge found.
pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
pnp: 00:08: ioport range 0x290-0x297 has been reserved
pnp: 00:09: iomem range 0xffafe000-0xffb0cbff could not be reserved
pnp: 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0f: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0f: iomem range 0xc0000-0xcffff has been reserved
pnp: 00:0f: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0f: iomem range 0x100000-0x7fffffff could not be reserved
ACPI: PCI Interrupt 0000:05:03.0[A] -> GSI 21 (level, low) -> IRQ 21
Time: tsc clocksource has been installed.
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]  MMIO=[feaff800-feafffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
PCI: Bridge: 0000:00:01.0
  IO window: 9000-9fff
  MEM window: fa700000-fe7fffff
  PREFETCH window: bfe00000-dfdfffff
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: dfe00000-dfefffff
PCI: Bridge: 0000:00:1c.4
  IO window: b000-bfff
  MEM window: fe900000-fe9fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
  IO window: a000-afff
  MEM window: fe800000-fe8fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: c000-cfff
  MEM window: fea00000-feafffff
  PREFETCH window: 88000000-880fffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 577k freed
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
io scheduler noop registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie02]
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000080000, using 10240k, total 262144k
vesafb: mode is 1280x1024x32, linelength=5120, pages=0
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 19 (level, low) -> IRQ 19
skge 1.11 addr 0xfeaf4000 irq 19 chip Yukon-Lite rev 9
skge eth0: addr 00:18:f3:75:9e:29
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
sky2 0000:02:00.0: v1.14 addr 0xfe8fc000 irq 17 Yukon-EC Ultra (0xb4) rev 2
sky2 eth1: addr 00:18:f3:75:b1:e8
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
ahci 0000:00:1f.2: version 2.2
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20000026900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314
ata2: SATA max UDMA/133 cmd 0xffffc20000026980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314
ata3: SATA max UDMA/133 cmd 0xffffc20000026a00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314
ata4: SATA max UDMA/133 cmd 0xffffc20000026a80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314
ata5: SATA max UDMA/133 cmd 0xffffc20000026b00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314
ata6: SATA max UDMA/133 cmd 0xffffc20000026b80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 314
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d80000e7f35c]
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: MAXTOR STM3250824AS, 3.AAJ, max UDMA/133
ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: HDS728080PLAT20, PF2OA21B, max UDMA/133
ata2.00: 160836480 sectors, multi 0: LBA48 
ata2.00: applying bridge limits
ata2.00: configured for UDMA/100
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      MAXTOR STM325082 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access     ATA      HDS728080PLAT20  PF2O PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 160836480 512-byte hardware sectors (82348 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 160836480 512-byte hardware sectors (82348 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg1 type 0
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:03:00.0 to 64
scsi6 : ahci
scsi7 : ahci
ata7: SATA max UDMA/133 cmd 0xffffc20000038100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
ata8: SATA max UDMA/133 cmd 0xffffc20000038180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:03:00.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:03:00.1 to 64
scsi8 : pata_jmicron
scsi9 : pata_jmicron
ata9: PATA max UDMA/100 cmd 0x000000000001bc00 ctl 0x000000000001b882 bmdma 0x000000000001b400 irq 17
ata10: PATA max UDMA/100 cmd 0x000000000001b800 ctl 0x000000000001b482 bmdma 0x000000000001b408 irq 17
ata9.00: ATAPI: HL-DT-ST DVDRAM GSA-H12N, UL01, max UDMA/66
ata9.01: ATAPI: HL-DT-STDVD-ROM GDR8164B, 0L06, max UDMA/33
ata9.00: configured for UDMA/66
ata9.01: configured for UDMA/33
scsi 8:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-H12N  UL01 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 8:0:0:0: Attached scsi CD-ROM sr0
sr 8:0:0:0: Attached scsi generic sg2 type 5
scsi 8:0:1:0: CD-ROM            HL-DT-ST DVD-ROM GDR8164B 0L06 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
sr 8:0:1:0: Attached scsi CD-ROM sr1
sr 8:0:1:0: Attached scsi generic sg3 type 5
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfebff400
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebff000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000e080
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000dc00
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
input: PC Speaker as /class/input/input3
input: ImExPS/2 Logitech Wheel Mouse as /class/input/input4
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA device list:
  #0: HDA Intel at 0xfebf8000 irq 22
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ReiserFS: sda5: found reiserfs format "3.6" with standard journal
ReiserFS: sda5: using ordered data mode
ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda5: checking transaction log (sda5)
ReiserFS: sda5: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 252k freed
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  1.0-9755  Mon Feb 26 23:16:31 PST 2007
ReiserFS: sdb2: found reiserfs format "3.6" with standard journal
ReiserFS: sdb2: using ordered data mode
ReiserFS: sdb2: journal params: device sdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb2: checking transaction log (sdb2)
ReiserFS: sdb2: Using r5 hash to sort names
fuse init (API version 7.8)
fuse distribution version: 2.6.4
Adding 2771204k swap on /dev/sdb4.  Priority:-1 extents:1 across:2771204k
skge eth0: enabling interface
skge eth0: Link is up at 100 Mbps, full duplex, flow control none
sky2 eth1: enabling interface
sky2 eth1: ram buffer 0K
sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control rx
sky2 eth1: Link is down.
sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control rx
sky2 eth1: Link is down.
sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both
sky2 eth1: Link is down.
sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both
sky2 eth1: Link is down.