Linux version 2.6.23-rc1-git4-27072007dw (root@dalpdw2) (gcc version 4.1.3 20070629 (prerelease) (Debian 4.1.2-13)) #1 SMP Fri Jul 27 09:51:07 CEST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000005f7d0000 (usable) BIOS-e820: 000000005f7d0000 - 000000005f7e5600 (reserved) BIOS-e820: 000000005f7e5600 - 000000005f7f8000 (ACPI NVS) BIOS-e820: 000000005f7f8000 - 000000005f800000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fed20000 - 00000000fed9b000 (reserved) BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 631MB HIGHMEM available. 896MB LOWMEM available. Entering add_active_range(0, 0, 391120) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 391120 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 391120 On node 0 totalpages: 391120 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 1263 pages used for memmap HighMem zone: 160481 pages, LIFO batch:31 Movable zone: 0 pages used for memmap DMI 2.4 present. ACPI: RSDP 000F7BD0, 0024 (r2 HP ) ACPI: XSDT 5F7E57C4, 0074 (r1 HPQOEM SLIC-MPC 1 HP 1) ACPI: FACP 5F7E5684, 00F4 (r4 HP 30A2 3 HP 1) ACPI: DSDT 5F7E5AC0, F9BB (r1 HP nx7400 10000 MSFT 100000E) ACPI: FACS 5F7F7E80, 0040 ACPI: SLIC 5F7E5838, 0176 (r1 HPQOEM SLIC-MPC 1 HP 1) ACPI: HPET 5F7E59B0, 0038 (r1 HP 30A2 1 HP 1) ACPI: APIC 5F7E59E8, 0068 (r1 HP 30A2 1 HP 1) ACPI: MCFG 5F7E5A50, 003C (r1 HP 30A2 1 HP 1) ACPI: TCPA 5F7E5A8C, 0032 (r2 HP 30A2 1 HP 1) ACPI: SSDT 5F7F547B, 0326 (r1 HP HPQSAT 1 MSFT 100000E) ACPI: SSDT 5F7F5FB4, 025F (r1 HP Cpu0Tst 3000 INTL 20060317) ACPI: SSDT 5F7F6213, 00A6 (r1 HP Cpu1Tst 3000 INTL 20060317) ACPI: SSDT 5F7F62B9, 04D7 (r1 HP CpuPm 3000 INTL 20060317) ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 6:15 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 60000000 (gap: 5f800000:9f400000) Built 1 zonelists in Zone order. Total pages: 388065 Kernel command line: root=/dev/sda7 ro vga=0x305 selinux=0 elevator=cfq video=vesafb:mtrr:3 pci=assign-busses mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c0422000 soft=c0420000 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1828.910 MHz processor. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1546784k/1564480k available (2215k kernel code, 16544k reserved, 759k data, 192k init, 646976k highmem) virtual kernel memory layout: fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc03ed000 - 0xc041d000 ( 192 kB) .data : 0xc0329c5c - 0xc03e78a4 ( 759 kB) .text : 0xc0100000 - 0xc0329c5c (2215 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Calibrating delay using timer specific routine.. 3660.76 BogoMIPS (lpj=1830383) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. Freeing SMP alternatives: 13k freed ACPI: Core revision 20070126 CPU0: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping 06 Booting processor 1/1 eip 3000 CPU 1 irqstacks, hard=c0423000 soft=c0421000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3657.51 BogoMIPS (lpj=1828756) CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping 06 Total of 2 processors activated (7318.27 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs HP Compaq Laptop series board detected. Selecting BIOS-method for reboots. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at f8000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: PCI BIOS revision 2.10 entry at 0xf0322, last bus=32 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62<6>ACPI: PCI Root Bridge [C002] (0000:00) PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1100-113f claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C098._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C104._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C114._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C11A._PRT] ACPI: PCI Interrupt Link [C110] (IRQs *10 11) ACPI: PCI Interrupt Link [C111] (IRQs *10 11) ACPI: PCI Interrupt Link [C112] (IRQs 10 *11) ACPI: PCI Interrupt Link [C113] (IRQs *10 11) ACPI: PCI Interrupt Link [C12C] (IRQs *10 11) ACPI: PCI Interrupt Link [C12D] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C12E] (IRQs 10 11) *0, disabled. ACPI Exception (pci_link-0184): AE_NOT_FOUND, Evaluating _PRS [20070126] ACPI: Power Resource [C200] (on) ACPI: Power Resource [C21D] (on) ACPI: Power Resource [C226] (off) ACPI: Power Resource [C320] (off) ACPI: Power Resource [C321] (off) ACPI: Power Resource [C322] (off) ACPI: Power Resource [C323] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Time: tsc clocksource has been installed. pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:00: iomem range 0x100000-0x5f7fffff could not be reserved pnp: 00:0a: iomem range 0xffb00000-0xffbfffff could not be reserved pnp: 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0b: ioport range 0x1000-0x107f has been reserved pnp: 00:0b: ioport range 0x1100-0x113f has been reserved pnp: 00:0b: ioport range 0x1200-0x121f has been reserved pnp: 00:0b: iomem range 0xf8000000-0xfbffffff has been reserved pnp: 00:0b: iomem range 0xfec00000-0xfec000ff could not be reserved pnp: 00:0b: iomem range 0xfed20000-0xfed3ffff could not be reserved pnp: 00:0b: iomem range 0xfed45000-0xfed8ffff could not be reserved pnp: 00:0c: iomem range 0xfeda0000-0xfedbffff could not be reserved pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.1 IO window: disabled. MEM window: f4000000-f40fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: 2000-3fff MEM window: f0000000-f3ffffff PREFETCH window: disabled. PCI: Bus 5, cardbus bridge: 0000:04:06.0 IO window: 00005000-000050ff IO window: 00005400-000054ff PREFETCH window: 60000000-63ffffff MEM window: 64000000-67ffffff PCI: Bridge: 0000:00:1e.0 IO window: 5000-5fff MEM window: f4100000-f43fffff PREFETCH window: 60000000-63ffffff ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.1 to 64 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.3 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt 0000:04:06.0[A] -> GSI 18 (level, low) -> IRQ 19 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. highmem bounce pool size: 64 pages SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler cfq registered (default) Boot video device is 0000:00:02.0 vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 1536k, total 7872k vesafb: mode is 1024x768x8, linelength=1024, pages=9 vesafb: scrolling: redraw vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device hpet_resources: 0xfed00000 is busy Linux agpgart interface v0.102 agpgart: Detected an Intel 945GM Chipset. agpgart: Detected 7932K stolen memory. agpgart: AGP aperture is 256M @ 0xe0000000 [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 [drm] Initialized i915 1.6.0 20060119 on minor 0 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled loop: module loaded b44.c:v1.01 (Jun 16, 2006) ACPI: PCI Interrupt 0000:04:0e.0[A] -> GSI 16 (level, low) -> IRQ 16 eth0: Broadcom 4400 10/100BaseT Ethernet 00:17:08:43:b3:8e ahci 0000:00:1f.2: version 2.3 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17 Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0xf impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 cmd 0xf8840100 ctl 0x00000000 bmdma 0x00000000 irq 223 ata2: SATA max UDMA/133 cmd 0xf8840180 ctl 0x00000000 bmdma 0x00000000 irq 223 ata3: SATA max UDMA/133 cmd 0xf8840200 ctl 0x00000000 bmdma 0x00000000 irq 223 ata4: SATA max UDMA/133 cmd 0xf8840280 ctl 0x00000000 bmdma 0x00000000 irq 223 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: FUJITSU MHV2080BH PL, 892C, max UDMA/100 ata1.00: 156301488 sectors, multi 16: LBA48 ata1.00: configured for UDMA/100 ata2: SATA link down (SStatus 0 SControl 0) ata3: SATA link down (SStatus 0 SControl 0) ata4: SATA link down (SStatus 0 SControl 0) scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2080B 892C PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 > sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 20, io base 0x00004020 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 17, io base 0x00004040 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 19, io base 0x00004060 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 18, io base 0x00004080 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected PNP: PS/2 Controller [PNP0303:C21A,PNP0f13:C21B] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode usb 3-2: new low speed USB device using uhci_hcd and address 2 usb 3-2: configuration #1 chosen from 1 choice Synaptics Touchpad, model: 1, fw: 6.2, id: 0x2580b1, caps: 0xa04793/0x300000 serio: Synaptics pass-through port at isa0060/serio4/input0 input: SynPS/2 Synaptics TouchPad as /class/input/input1 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 192k freed ACPI: SSDT 5F7F5869, 01FB (r1 HP Cpu0Ist 3000 INTL 20060317) ACPI: SSDT 5F7F5AE9, 04CB (r1 HP Cpu0Cst 3001 INTL 20060317) Monitor-Mwait will be used to enter C-1 state Monitor-Mwait will be used to enter C-2 state ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Processor [CPU0] (supports 8 throttling states) input: Power Button (FF) as /class/input/input2 ACPI: Power Button (FF) [PWRF] input: Sleep Button (CM) as /class/input/input3 ACPI: Sleep Button (CM) [C243] input: Lid Switch as /class/input/input4 ACPI: Lid Switch [C23C] ACPI: SSDT 5F7F57A1, 00C8 (r1 HP Cpu1Ist 3000 INTL 20060317) ACPI: SSDT 5F7F5A64, 0085 (r1 HP Cpu1Cst 3000 INTL 20060317) ACPI: CPU1 (power states: C1[C1] C2[C2]) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: AC Adapter [C1BC] (on-line) Marking TSC unstable due to: possible TSC halt in C2. Time: hpet clocksource has been installed. ACPI: Battery Slot [C1BE] (battery present) ACPI: Battery Slot [C1BD] (battery absent) ata_piix 0000:00:1f.1: version 2.11 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1f.1 to 64 scsi4 : ata_piix scsi5 : ata_piix ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000140a0 irq 14 ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x000140a8 irq 15 ata5.00: ATAPI: TSSTcorpCD/DVDW TS-L632D, HH15, max MWDMA2 input: PC Speaker as /class/input/input5 ata5.00: configured for MWDMA2 ata6: port disabled. ignoring. scsi 4:0:0:0: CD-ROM TSSTcorp CD/DVDW TS-L632D HH15 PQ: 0 ANSI: 5 scsi 4:0:0:0: Attached scsi generic sg1 type 5 ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xf4584000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected Real Time Clock Driver v1.12ac ACPI: Thermal Zone [TZ0] (51 C) ACPI: Thermal Zone [TZ1] (51 C) ACPI: Thermal Zone [TZ2] (45 C) Yenta: CardBus bridge found at 0000:04:06.0 [103c:30a2] Yenta: Enabling burst memory read transactions Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:04:06.0, mfunc 0x01011b22, devctl 0x64 ACPI: Thermal Zone [TZ3] (26 C) ACPI: Thermal Zone [TZ4] (23 C) HID device not claimed by input or hiddev ACPI: Transitioning device [C324] to D3 ACPI: Transitioning device [C324] to D3 ACPI: Fan [C324] (off) ACPI: Transitioning device [C325] to D3 ACPI: Transitioning device [C325] to D3 ACPI: Fan [C325] (off) ACPI: Transitioning device [C326] to D3 ACPI: Transitioning device [C326] to D3 ACPI: Fan [C326] (off) ACPI: Fan [C327] (on) sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 4:0:0:0: Attached scsi CD-ROM sr0 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1b.0 to 64 usb 3-2: USB disconnect, address 2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver si3054: cannot initialize. EXT MID = 0000 Yenta: ISA IRQ mask 0x0cf8, PCI irq 19 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0x5000 - 0x5fff pcmcia: parent PCI bridge Memory window: 0xf4100000 - 0xf43fffff pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff usb 3-2: new low speed USB device using uhci_hcd and address 3 usb 3-2: configuration #1 chosen from 1 choice input: Logitech Optical USB Mouse as /class/input/input6 input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.2-2 Adding 2623280k swap on /dev/sda12. Priority:-1 extents:1 across:2623280k EXT3 FS on sda7, internal journal XFS mounting filesystem sda10 Ending clean XFS mount for filesystem: sda10 XFS mounting filesystem sda8 Ending clean XFS mount for filesystem: sda8 XFS mounting filesystem sda9 Ending clean XFS mount for filesystem: sda9 XFS mounting filesystem sda11 Ending clean XFS mount for filesystem: sda11 b44: eth0: Link is up at 100 Mbps, full duplex. b44: eth0: Flow control is off for TX and off for RX.