sdio: add <linux/mmc/sdio_csr.h> for CSR specific CCCR registers

Signed-off-by: David Vrabel <david.vrabel@csr.com>
---
Index: mmc/include/linux/mmc/sdio_csr.h
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ mmc/include/linux/mmc/sdio_csr.h	2007-08-10 01:16:14.000000000 +0100
@@ -0,0 +1,116 @@
+/*
+ * SDIO CCCR vendor registers for CSR chips.
+ *
+ * Copyright (C) 2007 Cambridge Silicon Radio Ltd.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef LINUX_MMC_SDIO_CSR_H
+#define LINUX_MMC_SDIO_CSR_H
+
+/*
+ * Registers at 0xF0 - 0xFF in the CCCR are reserved for vendor
+ * specific registers.  The registers defined here are specific to
+ * following CSR chips:
+ *
+ *   - BlueCore (6 and later)
+ */
+
+/*
+ * Interrupt status/host wakeup register.
+ *
+ * This controls a function's deep sleep state.
+ *
+ * See enum sdio_sleep_state.
+ */
+#define SDIO_CSR_SLEEP_STATE 0xf0
+#  define SDIO_CSR_SLEEP_STATE_FUNC(f) ((f) << 4)
+#  define SDIO_CSR_SLEEP_STATE_RDY_INT_EN  0x02
+#  define SDIO_CSR_SLEEP_STATE_WAKE_REQ    0x01
+
+/*
+ * Host interrupt clear register.
+ *
+ * Writing a 1 to bit 0 clears an SDIO interrupt raised by a generic
+ * function.
+ */
+#define SDIO_CSR_HOST_INT 0xf1
+#  define SDIO_CSR_HOST_INT_CL 0x01
+
+/*
+ * From host scratch registers 0 and 1.
+ *
+ * Read/write registers that can be used for signalling between the
+ * host and the chip.
+ *
+ * The usage of this register depends on the version of the chip or
+ * firmware.
+ */
+#define SDIO_CSR_FROM_HOST_SCRATCH0 0xf2
+#define SDIO_CSR_FROM_HOST_SCRATCH1 0xf3
+
+/*
+ * To host scratch register 0 and 1.
+ *
+ * Read only registers that may be used for signalling between the
+ * chip and the host.
+ *
+ * The usage of this register depends on the version of the chip or
+ * firmware.
+ */
+#define SDIO_CSR_TO_HOST_SCRATCH0 0xf4
+#define SDIO_CSR_TO_HOST_SCRATCH1 0xf5
+
+/*
+ * Extended I/O enable.
+ *
+ * Similar to the standard CCCR I/O Enable register, this is used to
+ * detect if an internal reset of a function has occured and
+ * (optionally) reenable it.
+ *
+ * An internal reset is detected by CCCR I/O Enable bit being set and
+ * the corresponding EXT_IO_EN bit being clear.
+ */
+#define SDIO_CSR_EXT_IO_EN 0xf6
+
+/*
+ * Deep sleep states as set via the sleep state register.
+ *
+ * These states are used to control when the chip may go into a deep
+ * sleep (a low power mode).
+ *
+ * Since a chip in deep sleep may not respond to SDIO commands, the
+ * host should ensure that the chip is not in deep sleep before
+ * attempting SDIO commands to functions 1 to 7.
+ *
+ * The available states are:
+ *
+ * AWAKE - chip must not enter deep sleep and should exit deep sleep
+ * if it's currently sleeping.
+ *
+ * TORPID - chip may enter deep sleep.
+ *
+ * DROWSY - a transition state between TORPID and AWAKE.  This is
+ * AWAKE plus the chip asserts an interrupt when the chip is awake.
+ *
+ * See SDIO_CSR_SLEEP_STATE.
+ */
+enum sdio_csr_sleep_state {
+	SDIO_CSR_SLEEP_STATE_AWAKE  = SDIO_CSR_SLEEP_STATE_WAKE_REQ,
+	SDIO_CSR_SLEEP_STATE_DROWSY = SDIO_CSR_SLEEP_STATE_WAKE_REQ
+	                            | SDIO_CSR_SLEEP_STATE_RDY_INT_EN,
+	SDIO_CSR_SLEEP_STATE_TORPID = 0x00,
+};
+
+#endif /* LINUX_MMC_SDIO_CSR_H */