| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <200708310904.l7V94YE3015312@mi0.bluebottle.com>
Date: Fri, 31 Aug 2007 02:04:40 -0700
From: "n" <xellos@...ebottle.com>
To: "Alan Cox" <alan@...rguk.ukuu.org.uk>
Cc: <linux-ide@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: PROBLEM: kernel 2.6.22.6 pata_pdc202xx_old.c limiting to UDMA/33 instead of UDMA/100 (UPDATED 2.6.22.6)
Update with kernel 2.6.22.6 i am getting this error now
ata2.00: ATA-6: ST3120026A, 3.06, max UDMA/100
here is the new error.
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9c:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
here is dmseg output
[sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 3:0:0:0: [sde] Attached SCSI disk
scsi 3:0:1:0: Direct-Access ATA Maxtor 6Y120L0 YAR4 PQ: 0 ANSI: 5
sd 3:0:1:0: [sdf] 240121728 512-byte hardware sectors (122942 MB)
sd 3:0:1:0: [sdf] Write Protect is off
sd 3:0:1:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 3:0:1:0: [sdf] 240121728 512-byte hardware sectors (122942 MB)
sd 3:0:1:0: [sdf] Write Protect is off
sd 3:0:1:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdf: sdf1
sd 3:0:1:0: [sdf] Attached SCSI disk
usbmon: debugfs is not available
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:04.2[D] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
uhci_hcd 0000:00:04.2: UHCI Host Controller
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:04.2: irq 11, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:04.3[D] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
uhci_hcd 0000:00:04.3: UHCI Host Controller
uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:04.3: irq 11, io base 0x0000d000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@...hat.com
input: AT Translated Set 2 keyboard as /class/input/input2
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-2: new low speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
hiddev96: USB HID v1.10 Device [CPS UPS AE550] on usb-0000:00:04.2-1
input: Logitech USB Receiver as /class/input/input3
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:04.2-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25
2007 UTC).
ACPI: PCI Interrupt 0000:00:04.5[C] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:04.5 to 64
ALSA device list:
#0: VIA 82C686A/B rev20 with AD1881A at 0xb800, irq 10
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
XFS mounting filesystem sdc2
Ending clean XFS mount for filesystem: sdc2
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 208k freed
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:1:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:1:0: Attached scsi generic sg3 type 0
sd 3:0:0:0: Attached scsi generic sg4 type 0
sd 3:0:1:0: Attached scsi generic sg5 type 0
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
parport_pc: VIA parallel port: io=0x378, irq=7
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
eth0: RTL8169sb/8110sb at 0xe882c000, 00:14:d1:38:5e:25, IRQ 11
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKD] -> GSI 5 (level, low) ->
IRQ 5
eth1: RealTek RTL8139 at 0x8800, 00:40:05:3a:15:c4, IRQ 5
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
via686a 0000:00:04.4: base address not set - upgrade BIOS or use
force_addr=0xaddr
Adding 390560k swap on /dev/sdc1. Priority:-1 extents:1 across:390560k
XFS mounting filesystem sdc3
Ending clean XFS mount for filesystem: sdc3
XFS mounting filesystem sdc4
Ending clean XFS mount for filesystem: sdc4
XFS mounting filesystem sdd1
Ending clean XFS mount for filesystem: sdd1
XFS mounting filesystem sde1
Ending clean XFS mount for filesystem: sde1
XFS mounting filesystem sdf1
Ending clean XFS mount for filesystem: sdf1
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata2.01: (BMDMA stat 0x4)
ata2.01: cmd ca/00:01:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata2: soft resetting port
ata2.01: configured for UDMA/33
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata2.01: (BMDMA stat 0x4)
ata2.01: cmd ca/00:01:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata2: soft resetting port
ata2.01: configured for UDMA/33
ata2: EH complete
sd 1:0:1:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata2.01: (BMDMA stat 0x4)
ata2.01: cmd ca/00:01:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata2: soft resetting port
ata2.01: configured for UDMA/33
ata2: EH complete
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
ata2.01: limiting speed to UDMA/25:PIO4
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata2.01: (BMDMA stat 0x4)
ata2.01: cmd ca/00:01:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata2.01: (BMDMA stat 0x4)
ata2.01: cmd ca/00:01:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata2.01: (BMDMA stat 0x4)
ata2.01: cmd ca/00:01:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata2: soft resetting port
ata2.01: configured for UDMA/25
sd 1:0:1:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08
sd 1:0:1:0: [sdb] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 3f
sd 1:0:1:0: [sdb] ASC=0x47 ASCQ=0x0
end_request: I/O error, dev sdb, sector 63
ata2: EH complete
sd 1:0:1:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
Filesystem "sdb1": Disabling barriers, trial barrier write failed
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
XFS mounting filesystem sdb1
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 1:0:1:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9c:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9c:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9c:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9c:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9c:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9c:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
sd 1:0:1:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08
sd 1:0:1:0: [sdb] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 3f
sd 1:0:1:0: [sdb] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sdb, sector 117218341
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9d:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9d:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9d:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9d:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9d:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.01: cmd ca/00:00:25:9d:fc/00:00:00:00:00/f6 tag 0 cdb 0x0 data 131072
out
res 40/00:00:3f:00:00/00:00:00:00:00/f0 Emask 0x4 (timeout)
ata2: port is slow to respond, please be patient (Status 0xfe)
ata2: device not ready (errno=-16), forcing hardreset
ata2: soft resetting port
ata2.01: configured for UDMA/25
sd 1:0:1:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08
sd 1:0:1:0: [sdb] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 3f
sd 1:0:1:0: [sdb] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sdb, sector 117218597
ata2: EH complete
xfs_force_shutdown(sdb1,0x1) called from line 423 of file fs/xfs/xfs_rw.c.
Return address = 0xc020c098
Filesystem "sdb1": I/O Error Detected. Shutting down filesystem: sdb1
Please umount the filesystem, and rectify the problem(s)
I/O error in filesystem ("sdb1") meta-data dev sdb1 block 0x6fc9be6
("xlog_bwrite") error 5 buf count 262144
XFS: failed to locate log tail
XFS: log mount/recovery failed: error 5
XFS: log mount failed
sd 1:0:1:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 1:0:1:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
XFS mounting filesystem sda1
Ending clean XFS mount for filesystem: sda1
r8169: eth0: link up
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
ata1: soft resetting port
ata1.00: configured for UDMA/100
ata1: EH complete
sd 0:0:0:0: [sda] 398297088 512-byte hardware sectors (203928 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ata2: soft resetting port
ata2.01: configured for UDMA/25
ata2: EH complete
sd 1:0:1:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (5119 buckets, 40952 max)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Capability LSM initialized
eth1: no IPv6 routers present
eth0: no IPv6 routers present
PPP generic driver version 2.4.2
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ipv6tb: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
PPP BSD Compression module registered
Here is my previous post
(not sure if anyone read it im new to mailing lists also ata1 below is ata2
above since i changed it to port 2 so its the same seagate drive.)
hello, with kernel 2.6.22.5 using the new pata_pdc202xx_old driver it
doesn't
detect the cable right on this seagate drive (i tried switching ports /
cables ...etc)
it detects the maxtor drive fine no matter what port its on, the seagate
doesnt detect correctly on either port
ata1.00: ATA-6: ST3120026A, 3.06, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: configured for UDMA/33
ata2.00: ATA-7: Maxtor 6B200R0, max UDMA/133
ata2.00: 398297088 sectors, multi 16: LBA48
ata2.00: configured for UDMA/100
i was searching goolge and i found other uses with the same problem and had
seagate drives (maybe the cable detect code is differnt in seagate?)
btw only devices sda and sdb are on the pata_pdc202xx_old card.
sdc-g are on the new via driver.
i also get this error about 50 of them
(dmsg cut top output where it had info about the cable error) anyways if you
scroll down you will see errors like this
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:01:3f:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/33
ata1: EH complete ..etc
.... Ends up here
ata1: EH complete
ata1.00: limiting speed to PIO4
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9d:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9d:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for PIO4 <- pio4 so is it even going lower?
ata1: EH complete
here is most of output from dmsg if you need it.
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
pata_via 0000:00:04.1: version 0.3.1
scsi2 : pata_via
scsi3 : pata_via
ata3: PATA max UDMA/66 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001d800 irq 14
ata4: PATA max UDMA/66 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001d808 irq 15
ata3.00: ATA-6: Maxtor 5T040H4, TAH71DP0, max UDMA/100
ata3.00: 80043264 sectors, multi 16: LBA
ata3.01: ATA-6: WDC WD800BB-55JKC0, 05.01C05, max UDMA/100
ata3.01: 156301488 sectors, multi 16: LBA
ata3.00: configured for UDMA/66
ata3.01: configured for UDMA/66
ata4.00: ATA-5: MAXTOR 4K080H4, A08.1500, max UDMA/100
ata4.00: 156301488 sectors, multi 16: LBA
ata4.01: ATA-7: Maxtor 6Y120L0, YAR41VW0, max UDMA/133
ata4.01: 240121728 sectors, multi 16: LBA
ata4.00: configured for UDMA/66
ata4.01: configured for UDMA/66
scsi 2:0:0:0: Direct-Access ATA Maxtor 5T040H4 TAH7 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 80043264 512-byte hardware sectors (40982 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sdc] 80043264 512-byte hardware sectors (40982 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4
sd 2:0:0:0: [sdc] Attached SCSI disk
scsi 2:0:1:0: Direct-Access ATA WDC WD800BB-55JK 05.0 PQ: 0 ANSI: 5
sd 2:0:1:0: [sdd] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:1:0: [sdd] Write Protect is off
sd 2:0:1:0: [sdd] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:1:0: [sdd] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:1:0: [sdd] Write Protect is off
sd 2:0:1:0: [sdd] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdd: sdd1
sd 2:0:1:0: [sdd] Attached SCSI disk
scsi 3:0:0:0: Direct-Access ATA MAXTOR 4K080H4 A08. PQ: 0 ANSI: 5
sd 3:0:0:0: [sde] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 3:0:0:0: [sde] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sde: sde1
sd 3:0:0:0: [sde] Attached SCSI disk
scsi 3:0:1:0: Direct-Access ATA Maxtor 6Y120L0 YAR4 PQ: 0 ANSI: 5
sd 3:0:1:0: [sdf] 240121728 512-byte hardware sectors (122942 MB)
sd 3:0:1:0: [sdf] Write Protect is off
sd 3:0:1:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 3:0:1:0: [sdf] 240121728 512-byte hardware sectors (122942 MB)
sd 3:0:1:0: [sdf] Write Protect is off
sd 3:0:1:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdf: sdf1
sd 3:0:1:0: [sdf] Attached SCSI disk
usbmon: debugfs is not available
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:04.2[D] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
uhci_hcd 0000:00:04.2: UHCI Host Controller
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:04.2: irq 11, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:04.3[D] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
uhci_hcd 0000:00:04.3: UHCI Host Controller
uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:04.3: irq 11, io base 0x0000d000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@...hat.com
input: AT Translated Set 2 keyboard as /class/input/input2
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-2: new low speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
hiddev96: USB HID v1.10 Device [CPS UPS AE550] on usb-0000:00:04.2-1
input: Logitech USB Receiver as /class/input/input3
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:04.2-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25
2007 UTC).
ACPI: PCI Interrupt 0000:00:04.5[C] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:04.5 to 64
ALSA device list:
#0: VIA 82C686A/B rev20 with AD1881A at 0xb800, irq 10
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
XFS mounting filesystem sdc2
Ending clean XFS mount for filesystem: sdc2
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKD] -> GSI 5 (level, low) ->
IRQ 5
eth0: RealTek RTL8139 at 0x8800, 00:40:05:3a:15:c4, IRQ 5
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
eth1: RTL8169sb/8110sb at 0xe882c000, 00:14:d1:38:5e:25, IRQ 11
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
parport_pc: VIA parallel port: io=0x378, irq=7
via686a 0000:00:04.4: base address not set - upgrade BIOS or use
force_addr=0xaddr
Adding 390560k swap on /dev/sdc1. Priority:-1 extents:1 across:390560k
XFS mounting filesystem sdc3
Ending clean XFS mount for filesystem: sdc3
XFS mounting filesystem sdc4
Ending clean XFS mount for filesystem: sdc4
XFS mounting filesystem sdd1
Ending clean XFS mount for filesystem: sdd1
XFS mounting filesystem sde1
Ending clean XFS mount for filesystem: sde1
XFS mounting filesystem sdf1
Ending clean XFS mount for filesystem: sdf1
XFS mounting filesystem sdb1
Ending clean XFS mount for filesystem: sdb1
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:01:3f:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:01:3f:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:01:3f:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata1.00: limiting speed to UDMA/25:PIO4
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:01:3f:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:01:3f:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:01:3f:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out
res 51/84:00:3f:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 3f
sd 0:0:0:0: [sda] ASC=0x47 ASCQ=0x0
end_request: I/O error, dev sda, sector 63
ata1: EH complete
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
Filesystem "sda1": Disabling barriers, trial barrier write failed
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
XFS mounting filesystem sda1
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9c:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9c:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9c:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9c:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9c:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9c:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9c:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9c:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9c:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9c:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9c:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9c:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
06 fc 9c 21
sd 0:0:0:0: [sda] ASC=0x47 ASCQ=0x0
end_request: I/O error, dev sda, sector 117218337
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9d:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9d:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9d:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9d:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: limiting speed to PIO4
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x4)
ata1.00: cmd ca/00:00:21:9d:fc/00:00:00:00:00/e6 tag 0 cdb 0x0 data 131072
out
res 51/84:00:21:9d:fc/00:00:00:00:00/e6 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for PIO4
ata1: EH complete
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
xfs_force_shutdown(sda1,0x1) called from line 423 of file fs/xfs/xfs_rw.c.
Return address = 0xc020cea8
Filesystem "sda1": I/O Error Detected. Shutting down filesystem: sda1
Please umount the filesystem, and rectify the problem(s)
I/O error in filesystem ("sda1") meta-data dev sda1 block 0x6fc9be2
("xlog_bwrite") error 5 buf count 262144
XFS: failed to locate log tail
XFS: log mount/recovery failed: error 5
XFS: log mount failed
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
end of dmesg
there is nothing wrong with the xfs filesystem it mounts fine on the system
ide ports so this might be another bug in the new pdc driver
xfs_force_shutdown(sda1,0x1) called from line 423 of file fs/xfs/xfs_rw.c.
Return address = 0xc020cea8
Filesystem "sda1": I/O Error Detected. Shutting down filesystem: sda1
Please umount the filesystem, and rectify the problem(s)
I/O error in filesystem ("sda1") meta-data dev sda1 block 0x6fc9be2
("xlog_bwrite") error 5 buf count 262144
XFS: failed to locate log tail
XFS: log mount/recovery failed: error 5
XFS: log mount failed
###
after the kernel finnishes booting i can mount that drive fine (also all the
xfs_check xfs_repair ..etc say there is no errors) but i think the drive is
in pio4 by the time its done.
the ide old driver seemed to work ok with this drive also the system
mainboard ide ports work too.
i tried changing the drive jumpers around and that also didnt help
just to add i tried switching my drives around i moved a wd drive to port 2
of the pdc controller and it worked fine so if a maxtor and a wd drive is
hooked up it detects as udma100, this seems to be a error with seagate
drives only, and i should also note i tried the seagate on the mainboard
chipset (uses the pata_via.c driver) and it detected the seagate fine and
set udma 100 on it.
Im not sure whats differnt in pata_via.c and pata_pdc202xx_old.c but
somethings wrong with the cable / or mode set in the pdc driver, atleast
with seagate drives.
----------------------------------------------------------------------
Finally - A spam blocker that actually works.
http://www.bluebottle.com/tag/4
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists