| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20070910122038.1f1bb006.akpm@linux-foundation.org>
Date: Mon, 10 Sep 2007 12:20:38 -0700
From: Andrew Morton <akpm@...ux-foundation.org>
To: "Torsten Kaiser" <just.for.lkml@...glemail.com>
Cc: "Andy Whitcroft" <apw@...dowen.org>, linux-kernel@...r.kernel.org,
mel@....ul.ie, "Jens Axboe" <jens.axboe@...cle.com>,
linux-scsi@...r.kernel.org, linux-ide@...r.kernel.org
Subject: Re: 2.6.23-rc4-mm1
On Mon, 10 Sep 2007 20:59:49 +0200 "Torsten Kaiser" <just.for.lkml@...glemail.com> wrote:
> On 9/10/07, Andrew Morton <akpm@...ux-foundation.org> wrote:
> > On Mon, 10 Sep 2007 18:49:26 +0100 Andy Whitcroft <apw@...dowen.org> wrote:
> >
> > > I have a couple of old NUMA-Q systems which are unable to read their
> > > boot disks with 2.6.23-rc4-mm1. The disks appear to be recognised and
> > > even the partition tables read correctly, and then they go pop:
>
> I reported a similar problem on Sep 1, but until now got no response.
You still haven't had a response ;) Let's add a cc.
Oh, you reported it against 2.6.23-rc4-mm1
(http://lkml.org/lkml/2007/9/1/92) and I did cc linux-ide in my response.
I'll continue to point out where this sort of thing occurs because last
week I was told that a reson why so many bug reports are ignored is because
"linux-kernel has too much traffic".
> The system boots, reads the partition tables, starts the RAID and then
> kicks one drive out because of errors.
Andy is using qla1280. You're using sata. So it's probably a different
bug, with the same symptoms.
> > > qla1280: QLA1040 found on PCI bus 0, dev 10
> > > Clocksource tsc unstable (delta = 99922590 ns)
> > > Time: jiffies clocksource has been installed.
> > > scsi(0:0): Resetting SCSI BUS
> > > scsi0 : QLogic QLA1040 PCI to SCSI Host Adapter
> > > Firmware version: 7.65.06, Driver version 3.26
> > > scsi 0:0:0:0: Direct-Access IBM DGHS18X 0360 PQ: 0 ANSI: 3
> > > scsi(0:0:0:0): Sync: period 10, offset 12, Wide
> > > scsi 0:0:1:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> > > scsi(0:0:1:0): Sync: period 10, offset 12, Wide
> > > scsi 0:0:2:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> > > scsi(0:0:2:0): Sync: period 10, offset 12, Wide
> > > scsi 0:0:3:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> > > scsi(0:0:3:0): Sync: period 10, offset 12, Wide
> > > scsi 0:0:4:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> > > scsi(0:0:4:0): Sync: period 10, offset 12, Wide
> > > st: Version 20070203, fixed bufsize 32768, s/g segs 256
> > > sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
> > > sd 0:0:0:0: [sda] Write Protect is off
> > > sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
> > > sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
> > > sd 0:0:0:0: [sda] Write Protect is off
> > > sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
> > > sda: sda1
> [snip]
> > > sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> > > end_request: I/O error, dev sda, sector 63
> > > Buffer I/O error on device sda1, logical block 0
> > > Buffer I/O error on device sda1, logical block 1
> > > Buffer I/O error on device sda1, logical block 2
> > > Buffer I/O error on device sda1, logical block 3
> > > mount: fs type devfs not supported by kernel
> > > ext3: No journal on filesystem on sda1
> > > umount: devfs: not mounted
> > > sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> > > end_request: I/O error, dev sda, sector 28010831
> > > sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> > > end_request: I/O error, dev sda, sector 31080815
>
> >From my log:
> [ 3.890000] scsi0 : sata_sil24
> [ 3.900000] scsi1 : sata_sil24
> [ 3.900000] ata1: SATA max UDMA/100 host m128@...feffc00 port
> 0xefef8000 irq 16
> [ 3.920000] ata2: SATA max UDMA/100 host m128@...feffc00 port
> 0xefefa000 irq 16
> [ 4.300000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 4.360000] ata1.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
> [ 4.370000] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 4.430000] ata1.00: configured for UDMA/100
> [ 4.500000] ieee1394: Node added: ID:BUS[0-00:1023] GUID[0010dc00005cc354]
> [ 4.500000] ieee1394: Host added: ID:BUS[0-01:1023] GUID[0011d80000c4c261]
> [ 4.790000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 4.850000] ata2.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
> [ 4.860000] ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 4.920000] ata2.00: configured for UDMA/100
> [ 4.930000] scsi 0:0:0:0: Direct-Access ATA MAXTOR
> STM332082 3.AA PQ: 0 ANSI: 5
> [ 4.960000] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 4.980000] sd 0:0:0:0: [sda] Write Protect is off
> [ 4.990000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 4.990000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.020000] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 5.040000] sd 0:0:0:0: [sda] Write Protect is off
> [ 5.050000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 5.050000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.080000] sda: sda1 sda2
> [ 5.110000] sd 0:0:0:0: [sda] Attached SCSI disk
> [ 5.120000] scsi 1:0:0:0: Direct-Access ATA MAXTOR
> STM332082 3.AA PQ: 0 ANSI: 5
> [ 5.140000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
> [ 5.170000] sd 1:0:0:0: [sdb] Write Protect is off
> [ 5.180000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> [ 5.180000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.210000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
> [ 5.230000] sd 1:0:0:0: [sdb] Write Protect is off
> [ 5.240000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> [ 5.240000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.270000] sdb: sdb1 sdb2
> [ 5.300000] sd 1:0:0:0: [sdb] Attached SCSI disk
> [more normal boot messaged, 3-disk RAID5 starts]
> [ 63.420000] ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> [ 63.420000] ata2.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0
> cdb 0x0 data 4096 out
> [ 63.420000] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
> 0x4 (timeout)
> [ 63.420000] ata2.00: status: {DRDY }
> [ 63.420000] ata2: hard resetting link
> [ 65.720000] ata2: softreset failed (port not ready)
> [ 65.720000] ata2: reset failed (errno=-5), retrying in 8 secs
> [ 73.420000] ata2: hard resetting link
> [ 75.720000] ata2: softreset failed (port not ready)
> [ 75.720000] ata2: reset failed (errno=-5), retrying in 8 secs
> [ 83.420000] ata2: hard resetting link
> [ 85.720000] ata2: softreset failed (port not ready)
> [ 85.720000] ata2: reset failed (errno=-5), retrying in 33 secs
> [snip, disk gets kicked]
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550927
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550935
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550943
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
>
> More similar error messages in the old my LKML-mail.
>
> After sdb was removed from the array the system worked normal with
> only two drives.
> But on the next boot it kicked the second sata_sil24 disk from the
> array killing it.
Can you please confirm that this bug is present in -mm and not present in
mainline (yet)?
Thanks.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists