Linux version 2.6.22.9 (root@romig) (gcc version 3.4.3) #1 Wed Oct 3 19:14:10 BST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fdf0000 (usable) BIOS-e820: 000000001fdf0000 - 000000001fdfb000 (ACPI data) BIOS-e820: 000000001fdfb000 - 000000001fe00000 (ACPI NVS) BIOS-e820: 000000001fe00000 - 0000000020000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 509MB LOWMEM available. Entering add_active_range(0, 0, 130544) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 130544 early_node_map[1] active PFN ranges 0: 0 -> 130544 On node 0 totalpages: 130544 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 987 pages used for memmap Normal zone: 125461 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP 000F72D0, 0014 (r0 PTLTD ) ACPI: RSDT 1FDF79CA, 0028 (r1 PTLTD RSDT 6040000 LTP 0) ACPI: FACP 1FDFAF8C, 0074 (r1 SiS M650 6040000 PTL F4240) ACPI: DSDT 1FDF79F2, 359A (r1 Clevo 650M 6040000 MSFT 100000D) ACPI: FACS 1FDFBFC0, 0040 ACPI: PM-Timer IO Port: 0x8008 Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Built 1 zonelists. Total pages: 129525 Kernel command line: root=/dev/sda6 vga=778 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 2666.381 MHz processor. Console: colour VGA+ 132x43 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 514160k/522176k available (1982k kernel code, 7464k reserved, 710k data, 136k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffff8000 - 0xfffff000 ( 28 kB) vmalloc : 0xe0800000 - 0xffff6000 ( 503 MB) lowmem : 0xc0000000 - 0xdfdf0000 ( 509 MB) .init : 0xc03a4000 - 0xc03c6000 ( 136 kB) .data : 0xc02efab4 - 0xc03a168c ( 710 kB) .text : 0xc0100000 - 0xc02efab4 (1982 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5334.34 BogoMIPS (lpj=2667171) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: bfebf9ff 00000000 00000000 0000b080 00004400 00000000 00000000 Compat vDSO mapped to ffffe000. CPU: Intel Genuine Intel(R) CPU 2.66GHz stepping 09 Checking 'hlt' instruction... OK. ACPI: Core revision 20070126 ACPI: setting ELCR to 0800 (from 0a20) NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd9c8, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Enabling SiS 96x SMBus. ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs *11) ACPI: PCI Interrupt Link [LNKB] (IRQs *9) ACPI: PCI Interrupt Link [LNKC] (IRQs 5) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs *11) ACPI: PCI Interrupt Link [LNKE] (IRQs *11) ACPI: PCI Interrupt Link [LNKF] (IRQs *9) ACPI: PCI Interrupt Link [LNKG] (IRQs *9) ACPI: PCI Interrupt Link [LNKH] (IRQs 9) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:04: ioport range 0x8000-0x808f has been reserved pnp: 00:04: ioport range 0x8090-0x80ff has been reserved pnp: 00:04: ioport range 0x8100-0x811f has been reserved pnp: 00:04: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:04: ioport range 0xfe00-0xfe00 has been reserved Time: tsc clocksource has been installed. pnp: 00:04: iomem range 0xd0000-0xd3fff could not be reserved pnp: 00:04: iomem range 0xd8000-0xdbfff has been reserved pnp: 00:04: iomem range 0xfec00000-0xfecfffff could not be reserved pnp: 00:04: iomem range 0xfee00000-0xfeefffff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: ec100000-ec1fffff PREFETCH window: f0000000-f7ffffff PCI: Bus 2, cardbus bridge: 0000:00:0c.0 IO window: 00001c00-00001cff IO window: 00002000-000020ff PREFETCH window: 30000000-33ffffff MEM window: 34000000-37ffffff ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered NTFS driver 2.1.28 [Flags: R/O]. io scheduler noop registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 ACPI: AC Adapter [ADP0] (on-line) ACPI: Battery Slot [BAT0] (battery present) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input2 ACPI: Sleep Button (CM) [SLPB] input: Lid Switch as /class/input/input3 ACPI: Lid Switch [LID] ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THM0] (60 C) Non-volatile memory driver v1.2 8139too Fast Ethernet driver 0.9.28 PCI: Enabling device 0000:00:0a.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 eth0: RealTek RTL8139 at 0xe080a000, 00:90:f5:24:ff:0b, IRQ 11 eth0: Identified 8139 chip type 'RTL-8100B/8139D' pata_sis 0000:00:02.5: version 0.5.1 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:02.5[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 scsi0 : pata_sis scsi1 : pata_sis ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011000 irq 14 ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011008 irq 15 ata1.00: ATA-6: FUJITSU MHT2060AT, 009A, max UDMA/100 ata1.00: 117210240 sectors, multi 16: LBA ata1.00: configured for UDMA/100 ata2.00: ATAPI: SONY CD-RW/DVD-ROM CRX830E, JYK1, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA FUJITSU MHT2060A 009A PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 > sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: CD-ROM SONY CD-RW CRX830E JYK1 PQ: 0 ANSI: 5 scsi 1:0:0:0: Attached scsi generic sg1 type 5 PCI: Enabling device 0000:00:03.3 (0000 -> 0002) ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:00:03.3[D] -> Link [LNKH] -> GSI 9 (level, low) -> IRQ 9 ehci_hcd 0000:00:03.3: EHCI Host Controller ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1 PCI: cache line size of 128 is not supported by device 0000:00:03.3 ehci_hcd 0000:00:03.3: irq 9, io mem 0xec004000 ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11 ohci_hcd 0000:00:03.0: OHCI Host Controller ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:03.0: irq 11, io mem 0xec001000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 9 ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] -> GSI 9 (level, low) -> IRQ 9 ohci_hcd 0000:00:03.1: OHCI Host Controller ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:03.1: irq 9, io mem 0xec002000 usb 1-2: new high speed USB device using ehci_hcd and address 2 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 9 ACPI: PCI Interrupt 0000:00:03.2[C] -> Link [LNKG] -> GSI 9 (level, low) -> IRQ 9 ohci_hcd 0000:00:03.2: OHCI Host Controller ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:03.2: irq 9, io mem 0xec003000 usb 1-2: configuration #1 chosen from 1 choice usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usb 2-2: new full speed USB device using ohci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input4 Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC). PCI: Enabling device 0000:00:02.7 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 input: PS/2 Mouse as /class/input/input5 input: AlpsPS/2 ALPS GlidePoint as /class/input/input6 intel8x0_measure_ac97_clock: measured 50494 usecs intel8x0: clocking to 48000 ALSA device list: #0: SiS SI7012 with ALC200,200P at irq 5 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' Using IPI Shortcut mode VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 136k freed usb 1-2: reset high speed USB device using ehci_hcd and address 2 zd1211rw 1-2:1.0: firmware version 4725 zd1211rw 1-2:1.0: zd1211b chip 0586:3410 v4810 high 00-13-49 AL2230_RF pa0 g---S zd1211rw 1-2:1.0: eth1 usbcore: registered new interface driver zd1211rw Adding 497972k swap on /dev/sda8. Priority:1 extents:1 across:497972k NTFS volume version 3.1. SoftMAC: Open Authentication completed with 00:13:49:a0:1e:f9