[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20071005154209.24349.55451.stgit@ghaskins-t60p.haskins.net>
Date: Fri, 05 Oct 2007 11:42:09 -0400
From: Gregory Haskins <ghaskins@...ell.com>
To: mingo@...e.hu, tglx@...utronix.de, rostedt@...dmis.org
Cc: linux-rt-users@...r.kernel.org, linux-kernel@...r.kernel.org,
ghaskins@...ell.com
Subject: [PATCH 1/2] SERIAL_CONSOLE: Clean up some of the IO routines to
support locked and unlocked variants
This is a cleanup in preparation for the console-nodelay patch to follow
Signed-off-by: Gregory Haskins <ghaskins@...ell.com>
---
drivers/serial/8250.c | 459 ++++++++++++++++++++++++++-----------------------
1 files changed, 241 insertions(+), 218 deletions(-)
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index bec3cdf..e443098 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -351,7 +351,7 @@ static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
#endif
-static unsigned int serial_in(struct uart_8250_port *up, int offset)
+static unsigned int __serial_in(struct uart_8250_port *up, int offset)
{
unsigned int tmp;
offset = map_8250_in_reg(up, offset) << up->port.regshift;
@@ -386,8 +386,20 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset)
}
}
+static unsigned int serial_in(struct uart_8250_port *up, int offset)
+{
+ unsigned int ret;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ ret = __serial_in(up, offset);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ return ret;
+}
+
static void
-serial_out(struct uart_8250_port *up, int offset, int value)
+__serial_out(struct uart_8250_port *up, int offset, int value)
{
/* Save the offset before it's remapped */
int save_offset = offset;
@@ -427,7 +439,7 @@ serial_out(struct uart_8250_port *up, int offset, int value)
/* Read the IER to ensure any interrupt is cleared before
* returning from ISR. */
if (save_offset == UART_TX || save_offset == UART_IER)
- value = serial_in(up, UART_IER);
+ value = __serial_in(up, UART_IER);
break;
default:
@@ -435,6 +447,15 @@ serial_out(struct uart_8250_port *up, int offset, int value)
}
}
+static unsigned int serial_out(struct uart_8250_port *up, int offset, int value)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ __serial_out(up, offset, value);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
static void
serial_out_sync(struct uart_8250_port *up, int offset, int value)
{
@@ -445,11 +466,11 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value)
case UPIO_AU:
#endif
case UPIO_DWAPB:
- serial_out(up, offset, value);
- serial_in(up, UART_LCR); /* safe, no side-effects */
+ __serial_out(up, offset, value);
+ __serial_in(up, UART_LCR); /* safe, no side-effects */
break;
default:
- serial_out(up, offset, value);
+ __serial_out(up, offset, value);
}
}
@@ -459,20 +480,22 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value)
* needed for certain old 386 machines, I've left these #define's
* in....
*/
-#define serial_inp(up, offset) serial_in(up, offset)
-#define serial_outp(up, offset, value) serial_out(up, offset, value)
+#define __serial_inp(up, offset) __serial_in(up, offset)
+#define __serial_outp(up, offset, value) __serial_out(up, offset, value)
+#define serial_inp(up, offset) serial_in(up, offset)
+#define serial_outp(up, offset, value) serial_out(up, offset, value)
/* Uart divisor latch read */
static inline int _serial_dl_read(struct uart_8250_port *up)
{
- return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8;
+ return __serial_inp(up, UART_DLL) | __serial_inp(up, UART_DLM) << 8;
}
/* Uart divisor latch write */
static inline void _serial_dl_write(struct uart_8250_port *up, int value)
{
- serial_outp(up, UART_DLL, value & 0xff);
- serial_outp(up, UART_DLM, value >> 8 & 0xff);
+ __serial_outp(up, UART_DLL, value & 0xff);
+ __serial_outp(up, UART_DLM, value >> 8 & 0xff);
}
#if defined (CONFIG_SERIAL_8250_AU1X00)
@@ -520,8 +543,8 @@ static void serial_dl_write(struct uart_8250_port *up, int value)
*/
static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
{
- serial_out(up, UART_SCR, offset);
- serial_out(up, UART_ICR, value);
+ __serial_out(up, UART_SCR, offset);
+ __serial_out(up, UART_ICR, value);
}
static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
@@ -529,8 +552,8 @@ static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
unsigned int value;
serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
- serial_out(up, UART_SCR, offset);
- value = serial_in(up, UART_ICR);
+ __serial_out(up, UART_SCR, offset);
+ value = __serial_in(up, UART_ICR);
serial_icr_write(up, UART_ACR, up->acr);
return value;
@@ -542,10 +565,10 @@ static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
static inline void serial8250_clear_fifos(struct uart_8250_port *p)
{
if (p->capabilities & UART_CAP_FIFO) {
- serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO |
+ __serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO);
+ __serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
- serial_outp(p, UART_FCR, 0);
+ __serial_outp(p, UART_FCR, 0);
}
}
@@ -558,15 +581,15 @@ static inline void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
{
if (p->capabilities & UART_CAP_SLEEP) {
if (p->capabilities & UART_CAP_EFR) {
- serial_outp(p, UART_LCR, 0xBF);
- serial_outp(p, UART_EFR, UART_EFR_ECB);
- serial_outp(p, UART_LCR, 0);
+ __serial_outp(p, UART_LCR, 0xBF);
+ __serial_outp(p, UART_EFR, UART_EFR_ECB);
+ __serial_outp(p, UART_LCR, 0);
}
- serial_outp(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
+ __serial_outp(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
if (p->capabilities & UART_CAP_EFR) {
- serial_outp(p, UART_LCR, 0xBF);
- serial_outp(p, UART_EFR, 0);
- serial_outp(p, UART_LCR, 0);
+ __serial_outp(p, UART_LCR, 0xBF);
+ __serial_outp(p, UART_EFR, 0);
+ __serial_outp(p, UART_LCR, 0);
}
}
}
@@ -581,12 +604,12 @@ static int __enable_rsa(struct uart_8250_port *up)
unsigned char mode;
int result;
- mode = serial_inp(up, UART_RSA_MSR);
+ mode = __serial_inp(up, UART_RSA_MSR);
result = mode & UART_RSA_MSR_FIFO;
if (!result) {
- serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
- mode = serial_inp(up, UART_RSA_MSR);
+ __serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
+ mode = __serial_inp(up, UART_RSA_MSR);
result = mode & UART_RSA_MSR_FIFO;
}
@@ -605,7 +628,7 @@ static void enable_rsa(struct uart_8250_port *up)
spin_unlock_irq(&up->port.lock);
}
if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
- serial_outp(up, UART_RSA_FRR, 0);
+ __serial_outp(up, UART_RSA_FRR, 0);
}
}
@@ -624,12 +647,12 @@ static void disable_rsa(struct uart_8250_port *up)
up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
spin_lock_irq(&up->port.lock);
- mode = serial_inp(up, UART_RSA_MSR);
+ mode = __serial_inp(up, UART_RSA_MSR);
result = !(mode & UART_RSA_MSR_FIFO);
if (!result) {
- serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
- mode = serial_inp(up, UART_RSA_MSR);
+ __serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
+ mode = __serial_inp(up, UART_RSA_MSR);
result = !(mode & UART_RSA_MSR_FIFO);
}
@@ -650,28 +673,28 @@ static int size_fifo(struct uart_8250_port *up)
unsigned short old_dl;
int count;
- old_lcr = serial_inp(up, UART_LCR);
- serial_outp(up, UART_LCR, 0);
- old_fcr = serial_inp(up, UART_FCR);
- old_mcr = serial_inp(up, UART_MCR);
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+ old_lcr = __serial_inp(up, UART_LCR);
+ __serial_outp(up, UART_LCR, 0);
+ old_fcr = __serial_inp(up, UART_FCR);
+ old_mcr = __serial_inp(up, UART_MCR);
+ __serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
- serial_outp(up, UART_MCR, UART_MCR_LOOP);
- serial_outp(up, UART_LCR, UART_LCR_DLAB);
+ __serial_outp(up, UART_MCR, UART_MCR_LOOP);
+ __serial_outp(up, UART_LCR, UART_LCR_DLAB);
old_dl = serial_dl_read(up);
serial_dl_write(up, 0x0001);
- serial_outp(up, UART_LCR, 0x03);
+ __serial_outp(up, UART_LCR, 0x03);
for (count = 0; count < 256; count++)
- serial_outp(up, UART_TX, count);
+ __serial_outp(up, UART_TX, count);
mdelay(20);/* FIXME - schedule_timeout */
- for (count = 0; (serial_inp(up, UART_LSR) & UART_LSR_DR) &&
+ for (count = 0; (__serial_inp(up, UART_LSR) & UART_LSR_DR) &&
(count < 256); count++)
- serial_inp(up, UART_RX);
- serial_outp(up, UART_FCR, old_fcr);
- serial_outp(up, UART_MCR, old_mcr);
- serial_outp(up, UART_LCR, UART_LCR_DLAB);
+ __serial_inp(up, UART_RX);
+ __serial_outp(up, UART_FCR, old_fcr);
+ __serial_outp(up, UART_MCR, old_mcr);
+ __serial_outp(up, UART_LCR, UART_LCR_DLAB);
serial_dl_write(up, old_dl);
- serial_outp(up, UART_LCR, old_lcr);
+ __serial_outp(up, UART_LCR, old_lcr);
return count;
}
@@ -686,20 +709,20 @@ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
unsigned char old_dll, old_dlm, old_lcr;
unsigned int id;
- old_lcr = serial_inp(p, UART_LCR);
- serial_outp(p, UART_LCR, UART_LCR_DLAB);
+ old_lcr = __serial_inp(p, UART_LCR);
+ __serial_outp(p, UART_LCR, UART_LCR_DLAB);
- old_dll = serial_inp(p, UART_DLL);
- old_dlm = serial_inp(p, UART_DLM);
+ old_dll = __serial_inp(p, UART_DLL);
+ old_dlm = __serial_inp(p, UART_DLM);
- serial_outp(p, UART_DLL, 0);
- serial_outp(p, UART_DLM, 0);
+ __serial_outp(p, UART_DLL, 0);
+ __serial_outp(p, UART_DLM, 0);
- id = serial_inp(p, UART_DLL) | serial_inp(p, UART_DLM) << 8;
+ id = __serial_inp(p, UART_DLL) | __serial_inp(p, UART_DLM) << 8;
- serial_outp(p, UART_DLL, old_dll);
- serial_outp(p, UART_DLM, old_dlm);
- serial_outp(p, UART_LCR, old_lcr);
+ __serial_outp(p, UART_DLL, old_dll);
+ __serial_outp(p, UART_DLM, old_dlm);
+ __serial_outp(p, UART_LCR, old_lcr);
return id;
}
@@ -741,9 +764,9 @@ static void autoconfig_has_efr(struct uart_8250_port *up)
* recommended for new designs).
*/
up->acr = 0;
- serial_out(up, UART_LCR, 0xBF);
- serial_out(up, UART_EFR, UART_EFR_ECB);
- serial_out(up, UART_LCR, 0x00);
+ __serial_out(up, UART_LCR, 0xBF);
+ __serial_out(up, UART_EFR, UART_EFR_ECB);
+ __serial_out(up, UART_LCR, 0x00);
id1 = serial_icr_read(up, UART_ID1);
id2 = serial_icr_read(up, UART_ID2);
id3 = serial_icr_read(up, UART_ID3);
@@ -808,12 +831,12 @@ static void autoconfig_8250(struct uart_8250_port *up)
up->port.type = PORT_8250;
- scratch = serial_in(up, UART_SCR);
- serial_outp(up, UART_SCR, 0xa5);
- status1 = serial_in(up, UART_SCR);
- serial_outp(up, UART_SCR, 0x5a);
- status2 = serial_in(up, UART_SCR);
- serial_outp(up, UART_SCR, scratch);
+ scratch = __serial_in(up, UART_SCR);
+ __serial_outp(up, UART_SCR, 0xa5);
+ status1 = __serial_in(up, UART_SCR);
+ __serial_outp(up, UART_SCR, 0x5a);
+ status2 = __serial_in(up, UART_SCR);
+ __serial_outp(up, UART_SCR, scratch);
if (status1 == 0xa5 && status2 == 0x5a)
up->port.type = PORT_16450;
@@ -850,17 +873,17 @@ static void autoconfig_16550a(struct uart_8250_port *up)
* Check for presence of the EFR when DLAB is set.
* Only ST16C650V1 UARTs pass this test.
*/
- serial_outp(up, UART_LCR, UART_LCR_DLAB);
- if (serial_in(up, UART_EFR) == 0) {
- serial_outp(up, UART_EFR, 0xA8);
- if (serial_in(up, UART_EFR) != 0) {
+ __serial_outp(up, UART_LCR, UART_LCR_DLAB);
+ if (__serial_in(up, UART_EFR) == 0) {
+ __serial_outp(up, UART_EFR, 0xA8);
+ if (__serial_in(up, UART_EFR) != 0) {
DEBUG_AUTOCONF("EFRv1 ");
up->port.type = PORT_16650;
up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
} else {
DEBUG_AUTOCONF("Motorola 8xxx DUART ");
}
- serial_outp(up, UART_EFR, 0);
+ __serial_outp(up, UART_EFR, 0);
return;
}
@@ -868,8 +891,8 @@ static void autoconfig_16550a(struct uart_8250_port *up)
* Maybe it requires 0xbf to be written to the LCR.
* (other ST16C650V2 UARTs, TI16C752A, etc)
*/
- serial_outp(up, UART_LCR, 0xBF);
- if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
+ __serial_outp(up, UART_LCR, 0xBF);
+ if (__serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
DEBUG_AUTOCONF("EFRv2 ");
autoconfig_has_efr(up);
return;
@@ -882,35 +905,35 @@ static void autoconfig_16550a(struct uart_8250_port *up)
* switch back to bank 2, read it from EXCR1 again and check
* it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
*/
- serial_outp(up, UART_LCR, 0);
- status1 = serial_in(up, UART_MCR);
- serial_outp(up, UART_LCR, 0xE0);
- status2 = serial_in(up, 0x02); /* EXCR1 */
+ __serial_outp(up, UART_LCR, 0);
+ status1 = __serial_in(up, UART_MCR);
+ __serial_outp(up, UART_LCR, 0xE0);
+ status2 = __serial_in(up, 0x02); /* EXCR1 */
if (!((status2 ^ status1) & UART_MCR_LOOP)) {
- serial_outp(up, UART_LCR, 0);
- serial_outp(up, UART_MCR, status1 ^ UART_MCR_LOOP);
- serial_outp(up, UART_LCR, 0xE0);
- status2 = serial_in(up, 0x02); /* EXCR1 */
- serial_outp(up, UART_LCR, 0);
- serial_outp(up, UART_MCR, status1);
+ __serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_MCR, status1 ^ UART_MCR_LOOP);
+ __serial_outp(up, UART_LCR, 0xE0);
+ status2 = __serial_in(up, 0x02); /* EXCR1 */
+ __serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_MCR, status1);
if ((status2 ^ status1) & UART_MCR_LOOP) {
unsigned short quot;
- serial_outp(up, UART_LCR, 0xE0);
+ __serial_outp(up, UART_LCR, 0xE0);
quot = serial_dl_read(up);
quot <<= 3;
- status1 = serial_in(up, 0x04); /* EXCR2 */
+ status1 = __serial_in(up, 0x04); /* EXCR2 */
status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */
- serial_outp(up, 0x04, status1);
+ __serial_outp(up, 0x04, status1);
serial_dl_write(up, quot);
- serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_LCR, 0);
up->port.uartclk = 921600*16;
up->port.type = PORT_NS16550A;
@@ -925,15 +948,15 @@ static void autoconfig_16550a(struct uart_8250_port *up)
* Try setting it with and without DLAB set. Cheap clones
* set bit 5 without DLAB set.
*/
- serial_outp(up, UART_LCR, 0);
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
- status1 = serial_in(up, UART_IIR) >> 5;
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_outp(up, UART_LCR, UART_LCR_DLAB);
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
- status2 = serial_in(up, UART_IIR) >> 5;
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+ status1 = __serial_in(up, UART_IIR) >> 5;
+ __serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ __serial_outp(up, UART_LCR, UART_LCR_DLAB);
+ __serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+ status2 = __serial_in(up, UART_IIR) >> 5;
+ __serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ __serial_outp(up, UART_LCR, 0);
DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
@@ -951,15 +974,15 @@ static void autoconfig_16550a(struct uart_8250_port *up)
* trying to write and read a 1 just to make sure it's not
* already a 1 and maybe locked there before we even start start.
*/
- iersave = serial_in(up, UART_IER);
- serial_outp(up, UART_IER, iersave & ~UART_IER_UUE);
- if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
+ iersave = __serial_in(up, UART_IER);
+ __serial_outp(up, UART_IER, iersave & ~UART_IER_UUE);
+ if (!(__serial_in(up, UART_IER) & UART_IER_UUE)) {
/*
* OK it's in a known zero state, try writing and reading
* without disturbing the current state of the other bits.
*/
- serial_outp(up, UART_IER, iersave | UART_IER_UUE);
- if (serial_in(up, UART_IER) & UART_IER_UUE) {
+ __serial_outp(up, UART_IER, iersave | UART_IER_UUE);
+ if (__serial_in(up, UART_IER) & UART_IER_UUE) {
/*
* It's an Xscale.
* We'll leave the UART_IER_UUE bit set to 1 (enabled).
@@ -976,7 +999,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
*/
DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
}
- serial_outp(up, UART_IER, iersave);
+ __serial_outp(up, UART_IER, iersave);
}
/*
@@ -1021,8 +1044,8 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
* Note: this is safe as long as MCR bit 4 is clear
* and the device is in "PC" mode.
*/
- scratch = serial_inp(up, UART_IER);
- serial_outp(up, UART_IER, 0);
+ scratch = __serial_inp(up, UART_IER);
+ __serial_outp(up, UART_IER, 0);
#ifdef __i386__
outb(0xff, 0x080);
#endif
@@ -1030,13 +1053,13 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
* Mask out IER[7:4] bits for test as some UARTs (e.g. TL
* 16C754B) allow only to modify them if an EFR bit is set.
*/
- scratch2 = serial_inp(up, UART_IER) & 0x0f;
- serial_outp(up, UART_IER, 0x0F);
+ scratch2 = __serial_inp(up, UART_IER) & 0x0f;
+ __serial_outp(up, UART_IER, 0x0F);
#ifdef __i386__
outb(0, 0x080);
#endif
- scratch3 = serial_inp(up, UART_IER) & 0x0f;
- serial_outp(up, UART_IER, scratch);
+ scratch3 = __serial_inp(up, UART_IER) & 0x0f;
+ __serial_outp(up, UART_IER, scratch);
if (scratch2 != 0 || scratch3 != 0x0F) {
/*
* We failed; there's nothing here
@@ -1047,8 +1070,8 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
}
}
- save_mcr = serial_in(up, UART_MCR);
- save_lcr = serial_in(up, UART_LCR);
+ save_mcr = __serial_in(up, UART_MCR);
+ save_lcr = __serial_in(up, UART_LCR);
/*
* Check to see if a UART is really there. Certain broken
@@ -1060,9 +1083,9 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
* that conflicts with COM 1-4 --- we hope!
*/
if (!(up->port.flags & UPF_SKIP_TEST)) {
- serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
- status1 = serial_inp(up, UART_MSR) & 0xF0;
- serial_outp(up, UART_MCR, save_mcr);
+ __serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
+ status1 = __serial_inp(up, UART_MSR) & 0xF0;
+ __serial_outp(up, UART_MCR, save_mcr);
if (status1 != 0x90) {
DEBUG_AUTOCONF("LOOP test failed (%02x) ",
status1);
@@ -1079,12 +1102,12 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
* We also initialise the EFR (if any) to zero for later. The
* EFR occupies the same register location as the FCR and IIR.
*/
- serial_outp(up, UART_LCR, 0xBF);
- serial_outp(up, UART_EFR, 0);
- serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_LCR, 0xBF);
+ __serial_outp(up, UART_EFR, 0);
+ __serial_outp(up, UART_LCR, 0);
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- scratch = serial_in(up, UART_IIR) >> 6;
+ __serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ scratch = __serial_in(up, UART_IIR) >> 6;
DEBUG_AUTOCONF("iir=%d ", scratch);
@@ -1126,7 +1149,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
up->bugs |= UART_BUG_NOMSR;
#endif
- serial_outp(up, UART_LCR, save_lcr);
+ __serial_outp(up, UART_LCR, save_lcr);
if (up->capabilities != uart_config[up->port.type].flags) {
printk(KERN_WARNING
@@ -1147,15 +1170,15 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
*/
#ifdef CONFIG_SERIAL_8250_RSA
if (up->port.type == PORT_RSA)
- serial_outp(up, UART_RSA_FRR, 0);
+ __serial_outp(up, UART_RSA_FRR, 0);
#endif
- serial_outp(up, UART_MCR, save_mcr);
+ __serial_outp(up, UART_MCR, save_mcr);
serial8250_clear_fifos(up);
- serial_in(up, UART_RX);
+ __serial_in(up, UART_RX);
if (up->capabilities & UART_CAP_UUE)
- serial_outp(up, UART_IER, UART_IER_UUE);
+ __serial_outp(up, UART_IER, UART_IER_UUE);
else
- serial_outp(up, UART_IER, 0);
+ __serial_outp(up, UART_IER, 0);
out:
spin_unlock_irqrestore(&up->port.lock, flags);
@@ -1179,31 +1202,31 @@ static void autoconfig_irq(struct uart_8250_port *up)
/* forget possible initially masked and pending IRQ */
probe_irq_off(probe_irq_on());
- save_mcr = serial_inp(up, UART_MCR);
- save_ier = serial_inp(up, UART_IER);
- serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
+ save_mcr = __serial_inp(up, UART_MCR);
+ save_ier = __serial_inp(up, UART_IER);
+ __serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
irqs = probe_irq_on();
- serial_outp(up, UART_MCR, 0);
+ __serial_outp(up, UART_MCR, 0);
udelay (10);
if (up->port.flags & UPF_FOURPORT) {
- serial_outp(up, UART_MCR,
+ __serial_outp(up, UART_MCR,
UART_MCR_DTR | UART_MCR_RTS);
} else {
- serial_outp(up, UART_MCR,
+ __serial_outp(up, UART_MCR,
UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
}
- serial_outp(up, UART_IER, 0x0f); /* enable all intrs */
- (void)serial_inp(up, UART_LSR);
- (void)serial_inp(up, UART_RX);
- (void)serial_inp(up, UART_IIR);
- (void)serial_inp(up, UART_MSR);
- serial_outp(up, UART_TX, 0xFF);
+ __serial_outp(up, UART_IER, 0x0f); /* enable all intrs */
+ (void)__serial_inp(up, UART_LSR);
+ (void)__serial_inp(up, UART_RX);
+ (void)__serial_inp(up, UART_IIR);
+ (void)__serial_inp(up, UART_MSR);
+ __serial_outp(up, UART_TX, 0xFF);
udelay (20);
irq = probe_irq_off(irqs);
- serial_outp(up, UART_MCR, save_mcr);
- serial_outp(up, UART_IER, save_ier);
+ __serial_outp(up, UART_MCR, save_mcr);
+ __serial_outp(up, UART_IER, save_ier);
if (up->port.flags & UPF_FOURPORT)
outb_p(save_ICP, ICP);
@@ -1215,7 +1238,7 @@ static inline void __stop_tx(struct uart_8250_port *p)
{
if (p->ier & UART_IER_THRI) {
p->ier &= ~UART_IER_THRI;
- serial_out(p, UART_IER, p->ier);
+ __serial_out(p, UART_IER, p->ier);
}
}
@@ -1242,13 +1265,13 @@ static void serial8250_start_tx(struct uart_port *port)
if (!(up->ier & UART_IER_THRI)) {
up->ier |= UART_IER_THRI;
- serial_out(up, UART_IER, up->ier);
+ __serial_out(up, UART_IER, up->ier);
if (up->bugs & UART_BUG_TXEN) {
unsigned char lsr, iir;
- lsr = serial_in(up, UART_LSR);
+ lsr = __serial_in(up, UART_LSR);
up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
- iir = serial_in(up, UART_IIR) & 0x0f;
+ iir = __serial_in(up, UART_IIR) & 0x0f;
if ((up->port.type == PORT_RM9000) ?
(lsr & UART_LSR_THRE &&
(iir == UART_IIR_NO_INT || iir == UART_IIR_THRI)) :
@@ -1272,7 +1295,7 @@ static void serial8250_stop_rx(struct uart_port *port)
up->ier &= ~UART_IER_RLSI;
up->port.read_status_mask &= ~UART_LSR_DR;
- serial_out(up, UART_IER, up->ier);
+ __serial_out(up, UART_IER, up->ier);
}
static void serial8250_enable_ms(struct uart_port *port)
@@ -1284,7 +1307,7 @@ static void serial8250_enable_ms(struct uart_port *port)
return;
up->ier |= UART_IER_MSI;
- serial_out(up, UART_IER, up->ier);
+ __serial_out(up, UART_IER, up->ier);
}
static void
@@ -1296,7 +1319,7 @@ receive_chars(struct uart_8250_port *up, unsigned int *status)
char flag;
do {
- ch = serial_inp(up, UART_RX);
+ ch = __serial_inp(up, UART_RX);
flag = TTY_NORMAL;
up->port.icount.rx++;
@@ -1344,7 +1367,7 @@ receive_chars(struct uart_8250_port *up, unsigned int *status)
uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
ignore_char:
- lsr = serial_inp(up, UART_LSR);
+ lsr = __serial_inp(up, UART_LSR);
} while ((lsr & UART_LSR_DR) && (max_count-- > 0));
spin_unlock(&up->port.lock);
tty_flip_buffer_push(tty);
@@ -1358,7 +1381,7 @@ static void transmit_chars(struct uart_8250_port *up)
int count;
if (up->port.x_char) {
- serial_outp(up, UART_TX, up->port.x_char);
+ __serial_outp(up, UART_TX, up->port.x_char);
up->port.icount.tx++;
up->port.x_char = 0;
return;
@@ -1374,7 +1397,7 @@ static void transmit_chars(struct uart_8250_port *up)
count = up->tx_loadsz;
do {
- serial_out(up, UART_TX, xmit->buf[xmit->tail]);
+ __serial_out(up, UART_TX, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_empty(xmit))
@@ -1392,7 +1415,7 @@ static void transmit_chars(struct uart_8250_port *up)
static unsigned int check_modem_status(struct uart_8250_port *up)
{
- unsigned int status = serial_in(up, UART_MSR);
+ unsigned int status = __serial_in(up, UART_MSR);
status |= up->msr_saved_flags;
up->msr_saved_flags = 0;
@@ -1424,7 +1447,7 @@ serial8250_handle_port(struct uart_8250_port *up)
spin_lock_irqsave(&up->port.lock, flags);
- status = serial_inp(up, UART_LSR);
+ status = __serial_inp(up, UART_LSR);
DEBUG_INTR("status = %x...", status);
@@ -1471,7 +1494,7 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id)
up = list_entry(l, struct uart_8250_port, list);
- iir = serial_in(up, UART_IIR);
+ iir = __serial_in(up, UART_IIR);
if (!(iir & UART_IIR_NO_INT)) {
serial8250_handle_port(up);
@@ -1486,7 +1509,7 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id)
* the UART status register (USR) and the LCR re-written. */
unsigned int status;
status = *(volatile u32 *)up->port.private_data;
- serial_out(up, UART_LCR, up->lcr);
+ __serial_out(up, UART_LCR, up->lcr);
handled = 1;
@@ -1595,7 +1618,7 @@ static void serial8250_timeout(unsigned long data)
struct uart_8250_port *up = (struct uart_8250_port *)data;
unsigned int iir;
- iir = serial_in(up, UART_IIR);
+ iir = __serial_in(up, UART_IIR);
if (!(iir & UART_IIR_NO_INT))
serial8250_handle_port(up);
mod_timer(&up->timer, jiffies + poll_timeout(up->port.timeout));
@@ -1612,11 +1635,11 @@ static void serial8250_backup_timeout(unsigned long data)
* based handler.
*/
if (is_real_interrupt(up->port.irq)) {
- ier = serial_in(up, UART_IER);
- serial_out(up, UART_IER, 0);
+ ier = __serial_in(up, UART_IER);
+ __serial_out(up, UART_IER, 0);
}
- iir = serial_in(up, UART_IIR);
+ iir = __serial_in(up, UART_IIR);
/*
* This should be a safe test for anyone who doesn't trust the
@@ -1639,7 +1662,7 @@ static void serial8250_backup_timeout(unsigned long data)
serial8250_handle_port(up);
if (is_real_interrupt(up->port.irq))
- serial_out(up, UART_IER, ier);
+ __serial_out(up, UART_IER, ier);
/* Standard timer interval plus 0.2s to keep the port running */
mod_timer(&up->timer, jiffies + poll_timeout(up->port.timeout) + HZ/5);
@@ -1652,7 +1675,7 @@ static unsigned int serial8250_tx_empty(struct uart_port *port)
unsigned int lsr;
spin_lock_irqsave(&up->port.lock, flags);
- lsr = serial_in(up, UART_LSR);
+ lsr = __serial_in(up, UART_LSR);
up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
spin_unlock_irqrestore(&up->port.lock, flags);
@@ -1697,7 +1720,7 @@ static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
- serial_out(up, UART_MCR, mcr);
+ __serial_out(up, UART_MCR, mcr);
}
static void serial8250_break_ctl(struct uart_port *port, int break_state)
@@ -1710,7 +1733,7 @@ static void serial8250_break_ctl(struct uart_port *port, int break_state)
up->lcr |= UART_LCR_SBC;
else
up->lcr &= ~UART_LCR_SBC;
- serial_out(up, UART_LCR, up->lcr);
+ __serial_out(up, UART_LCR, up->lcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
@@ -1725,7 +1748,7 @@ static inline void wait_for_xmitr(struct uart_8250_port *up, int bits)
/* Wait up to 10ms for the character(s) to be sent. */
do {
- status = serial_in(up, UART_LSR);
+ status = __serial_in(up, UART_LSR);
up->lsr_saved_flags |= status & LSR_SAVE_FLAGS;
@@ -1738,7 +1761,7 @@ static inline void wait_for_xmitr(struct uart_8250_port *up, int bits)
if (up->port.flags & UPF_CONS_FLOW) {
unsigned int tmout;
for (tmout = 1000000; tmout; tmout--) {
- unsigned int msr = serial_in(up, UART_MSR);
+ unsigned int msr = __serial_in(up, UART_MSR);
up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
if (msr & UART_MSR_CTS)
break;
@@ -1761,14 +1784,14 @@ static int serial8250_startup(struct uart_port *port)
if (up->port.type == PORT_16C950) {
/* Wake up and initialize UART */
up->acr = 0;
- serial_outp(up, UART_LCR, 0xBF);
- serial_outp(up, UART_EFR, UART_EFR_ECB);
- serial_outp(up, UART_IER, 0);
- serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_LCR, 0xBF);
+ __serial_outp(up, UART_EFR, UART_EFR_ECB);
+ __serial_outp(up, UART_IER, 0);
+ __serial_outp(up, UART_LCR, 0);
serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
- serial_outp(up, UART_LCR, 0xBF);
- serial_outp(up, UART_EFR, UART_EFR_ECB);
- serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_LCR, 0xBF);
+ __serial_outp(up, UART_EFR, UART_EFR_ECB);
+ __serial_outp(up, UART_LCR, 0);
}
#ifdef CONFIG_SERIAL_8250_RSA
@@ -1788,10 +1811,10 @@ static int serial8250_startup(struct uart_port *port)
/*
* Clear the interrupt registers.
*/
- (void) serial_inp(up, UART_LSR);
- (void) serial_inp(up, UART_RX);
- (void) serial_inp(up, UART_IIR);
- (void) serial_inp(up, UART_MSR);
+ (void) __serial_inp(up, UART_LSR);
+ (void) __serial_inp(up, UART_RX);
+ (void) __serial_inp(up, UART_IIR);
+ (void) __serial_inp(up, UART_MSR);
/*
* At this point, there's no way the LSR could still be 0xff;
@@ -1799,7 +1822,7 @@ static int serial8250_startup(struct uart_port *port)
* here.
*/
if (!(up->port.flags & UPF_BUGGY_UART) &&
- (serial_inp(up, UART_LSR) == 0xff)) {
+ (__serial_inp(up, UART_LSR) == 0xff)) {
printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
return -ENODEV;
}
@@ -1810,15 +1833,15 @@ static int serial8250_startup(struct uart_port *port)
if (up->port.type == PORT_16850) {
unsigned char fctr;
- serial_outp(up, UART_LCR, 0xbf);
+ __serial_outp(up, UART_LCR, 0xbf);
- fctr = serial_inp(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
- serial_outp(up, UART_FCTR, fctr | UART_FCTR_TRGD | UART_FCTR_RX);
- serial_outp(up, UART_TRG, UART_TRG_96);
- serial_outp(up, UART_FCTR, fctr | UART_FCTR_TRGD | UART_FCTR_TX);
- serial_outp(up, UART_TRG, UART_TRG_96);
+ fctr = __serial_inp(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
+ __serial_outp(up, UART_FCTR, fctr | UART_FCTR_TRGD | UART_FCTR_RX);
+ __serial_outp(up, UART_TRG, UART_TRG_96);
+ __serial_outp(up, UART_FCTR, fctr | UART_FCTR_TRGD | UART_FCTR_TX);
+ __serial_outp(up, UART_TRG, UART_TRG_96);
- serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_LCR, 0);
}
if (is_real_interrupt(up->port.irq)) {
@@ -1835,12 +1858,12 @@ static int serial8250_startup(struct uart_port *port)
wait_for_xmitr(up, UART_LSR_THRE);
serial_out_sync(up, UART_IER, UART_IER_THRI);
udelay(1); /* allow THRE to set */
- serial_in(up, UART_IIR);
- serial_out(up, UART_IER, 0);
+ __serial_in(up, UART_IIR);
+ __serial_out(up, UART_IER, 0);
serial_out_sync(up, UART_IER, UART_IER_THRI);
udelay(1); /* allow a working UART time to re-assert THRE */
- iir = serial_in(up, UART_IIR);
- serial_out(up, UART_IER, 0);
+ iir = __serial_in(up, UART_IIR);
+ __serial_out(up, UART_IER, 0);
spin_unlock_irqrestore(&up->port.lock, flags);
@@ -1874,7 +1897,7 @@ static int serial8250_startup(struct uart_port *port)
/*
* Now, initialize the UART
*/
- serial_outp(up, UART_LCR, UART_LCR_WLEN8);
+ __serial_outp(up, UART_LCR, UART_LCR_WLEN8);
spin_lock_irqsave(&up->port.lock, flags);
if (up->port.flags & UPF_FOURPORT) {
@@ -1893,10 +1916,10 @@ static int serial8250_startup(struct uart_port *port)
* Do a quick test to see if we receive an
* interrupt when we enable the TX irq.
*/
- serial_outp(up, UART_IER, UART_IER_THRI);
- lsr = serial_in(up, UART_LSR);
- iir = serial_in(up, UART_IIR);
- serial_outp(up, UART_IER, 0);
+ __serial_outp(up, UART_IER, UART_IER_THRI);
+ lsr = __serial_in(up, UART_LSR);
+ iir = __serial_in(up, UART_IIR);
+ __serial_outp(up, UART_IER, 0);
if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) {
if (!(up->bugs & UART_BUG_TXEN)) {
@@ -1915,10 +1938,10 @@ static int serial8250_startup(struct uart_port *port)
* saved flags to avoid getting false values from polling
* routines or the previous session.
*/
- serial_inp(up, UART_LSR);
- serial_inp(up, UART_RX);
- serial_inp(up, UART_IIR);
- serial_inp(up, UART_MSR);
+ __serial_inp(up, UART_LSR);
+ __serial_inp(up, UART_RX);
+ __serial_inp(up, UART_IIR);
+ __serial_inp(up, UART_MSR);
up->lsr_saved_flags = 0;
up->msr_saved_flags = 0;
@@ -1928,7 +1951,7 @@ static int serial8250_startup(struct uart_port *port)
* anyway, so we don't enable them here.
*/
up->ier = UART_IER_RLSI | UART_IER_RDI;
- serial_outp(up, UART_IER, up->ier);
+ __serial_outp(up, UART_IER, up->ier);
if (up->port.flags & UPF_FOURPORT) {
unsigned int icp;
@@ -1952,7 +1975,7 @@ static void serial8250_shutdown(struct uart_port *port)
* Disable interrupts from this port
*/
up->ier = 0;
- serial_outp(up, UART_IER, 0);
+ __serial_outp(up, UART_IER, 0);
spin_lock_irqsave(&up->port.lock, flags);
if (up->port.flags & UPF_FOURPORT) {
@@ -1968,7 +1991,7 @@ static void serial8250_shutdown(struct uart_port *port)
/*
* Disable break condition and FIFOs
*/
- serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
+ __serial_out(up, UART_LCR, __serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
serial8250_clear_fifos(up);
#ifdef CONFIG_SERIAL_8250_RSA
@@ -1982,7 +2005,7 @@ static void serial8250_shutdown(struct uart_port *port)
* Read data port to reset things, and then unlink from
* the IRQ chain.
*/
- (void) serial_in(up, UART_RX);
+ (void) __serial_in(up, UART_RX);
del_timer_sync(&up->timer);
up->timer.function = serial8250_timeout;
@@ -2128,7 +2151,7 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
if (up->capabilities & UART_CAP_UUE)
up->ier |= UART_IER_UUE | UART_IER_RTOIE;
- serial_out(up, UART_IER, up->ier);
+ __serial_out(up, UART_IER, up->ier);
if (up->capabilities & UART_CAP_EFR) {
unsigned char efr = 0;
@@ -2140,8 +2163,8 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
if (termios->c_cflag & CRTSCTS)
efr |= UART_EFR_CTS;
- serial_outp(up, UART_LCR, 0xBF);
- serial_outp(up, UART_EFR, efr);
+ __serial_outp(up, UART_LCR, 0xBF);
+ __serial_outp(up, UART_EFR, efr);
}
#ifdef CONFIG_ARCH_OMAP15XX
@@ -2149,17 +2172,17 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
if (cpu_is_omap1510() && is_omap_port((unsigned int)up->port.membase)) {
if (baud == 115200) {
quot = 1;
- serial_out(up, UART_OMAP_OSC_12M_SEL, 1);
+ __serial_out(up, UART_OMAP_OSC_12M_SEL, 1);
} else
- serial_out(up, UART_OMAP_OSC_12M_SEL, 0);
+ __serial_out(up, UART_OMAP_OSC_12M_SEL, 0);
}
#endif
if (up->capabilities & UART_NATSEMI) {
/* Switch to bank 2 not bank 1, to avoid resetting EXCR2 */
- serial_outp(up, UART_LCR, 0xe0);
+ __serial_outp(up, UART_LCR, 0xe0);
} else {
- serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
+ __serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
}
serial_dl_write(up, quot);
@@ -2169,16 +2192,16 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
* is written without DLAB set, this mode will be disabled.
*/
if (up->port.type == PORT_16750)
- serial_outp(up, UART_FCR, fcr);
+ __serial_outp(up, UART_FCR, fcr);
- serial_outp(up, UART_LCR, cval); /* reset DLAB */
+ __serial_outp(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
if (up->port.type != PORT_16750) {
if (fcr & UART_FCR_ENABLE_FIFO) {
/* emulated UARTs (Lucent Venus 167x) need two steps */
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ __serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
}
- serial_outp(up, UART_FCR, fcr); /* set fcr */
+ __serial_outp(up, UART_FCR, fcr); /* set fcr */
}
serial8250_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
@@ -2463,7 +2486,7 @@ static void serial8250_console_putchar(struct uart_port *port, int ch)
struct uart_8250_port *up = (struct uart_8250_port *)port;
wait_for_xmitr(up, UART_LSR_THRE);
- serial_out(up, UART_TX, ch);
+ __serial_out(up, UART_TX, ch);
}
/*
@@ -2490,12 +2513,12 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count)
/*
* First save the IER then disable the interrupts
*/
- ier = serial_in(up, UART_IER);
+ ier = __serial_in(up, UART_IER);
if (up->capabilities & UART_CAP_UUE)
- serial_out(up, UART_IER, UART_IER_UUE);
+ __serial_out(up, UART_IER, UART_IER_UUE);
else
- serial_out(up, UART_IER, 0);
+ __serial_out(up, UART_IER, 0);
uart_console_write(&up->port, s, count, serial8250_console_putchar);
@@ -2504,7 +2527,7 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count)
* and restore the IER
*/
wait_for_xmitr(up, BOTH_EMPTY);
- serial_out(up, UART_IER, ier);
+ __serial_out(up, UART_IER, ier);
/*
* The receive handling will happen properly because the
@@ -2640,14 +2663,14 @@ void serial8250_resume_port(int line)
unsigned char tmp;
/* Ensure it's still in high speed mode */
- serial_outp(up, UART_LCR, 0xE0);
+ __serial_outp(up, UART_LCR, 0xE0);
- tmp = serial_in(up, 0x04); /* EXCR2 */
+ tmp = __serial_in(up, 0x04); /* EXCR2 */
tmp &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
tmp |= 0x10; /* 1.625 divisor for baud_base --> 921600 */
- serial_outp(up, 0x04, tmp);
+ __serial_outp(up, 0x04, tmp);
- serial_outp(up, UART_LCR, 0);
+ __serial_outp(up, UART_LCR, 0);
}
uart_resume_port(&serial8250_reg, &up->port);
}
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists